- 04 1月, 2008 2 次提交
-
-
由 Shinya Kuribayashi 提交于
Assigning the output of simple_strtoul(CB:A9:87:65:43:21) to `char', we are warned as below: U-Boot 1.2.0 (Aug 30 2007 - 08:27:37) DRAM: 256 MB Flash: 32 MB In: serial Out: serial Err: serial Net: NEC-Candy Warning: NEC-Candy MAC addresses don't match: Address in SROM is 00:00:4C:80:92:A2 Address in environment is FFFFFFCB:FFFFFFA9:FFFFFF87:65:43:21 This patch changes env_enetaddr type from `char' to `unsigned char'. Cc: Masaki Ishikawa <ishikawa-masaki@cnt.mxe.nes.nec.co.jp> Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
由 Rafal Jaworowski 提交于
The purpose of this routine is receiving a single network frame, outside of U-Boot's NetLoop(). Exporting it to standalone programs that run on top of U-Boot will let them utilise networking facilities. For sending a raw frame the already existing eth_send() can be used. The direct consumer of this routine is the newly introduced API layer for external applications (enabled with CONFIG_API). Signed-off-by: NRafal Jaworowski <raj@semihalf.com> Signed-off-by: NPiotr Kruszynski <ppk@semihalf.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com>
-
- 06 11月, 2007 1 次提交
-
-
由 Roy Zang 提交于
This patch implements general ULi 526x Ethernet driver. Until now, it is the only native Ethernet port on MPC8610HPCD board, but it could be used on other boards with ULi 526x Ethernet port as well. Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com> Signed-off-by: NZhang Wei <wei.zhang@freescale.com> Acked-by: NJon Loeliger <jdl@freescale.com> Signed-off-by: NBen Warren <bwarren@qstreams.com>
-
- 14 8月, 2007 2 次提交
-
-
由 Wolfgang Denk 提交于
-
由 David Updegraff 提交于
Implemented IETF RFC2090, Multicast TFTP. Initial implementation on Realtek RTL8139 and Freescale TSEC. Signed-off-by: NDavid Updegraff <dave@cray.com> Signed-off-by: NBen Warren <bwarren@qstreams.com>
-
- 11 8月, 2007 1 次提交
-
-
由 Sergey Kubushyn 提交于
Add support for the following DaVinci boards: - DV_EVM - SCHMOOGIE - SONATA Changes: - Split into separate board directories - Removed changes to MTD_DEBUG (or whatever it's called) - New CONFIG_CMD party line followed - Some cosmetic fixes, cleanup etc. - Patches against the latest U-Boot tree as of now. - Fixed CONFIG_CMD_NET in net files. - Fixed CONFIG_CMD_EEPROM for schmoogie. - Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and DV_EVM. Can't check if it works on SONATA, don't have a board any more, but it at least compiles. Here is an excerpt from session log on SCHMOOGIE... U-Boot 1.2.0-g6c33c785-dirty (Aug 7 2007 - 13:07:17) DRAM: 128 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock : 297MHz DDR Clock : 162MHz ETH PHY : DP83848 @ 0x01 U-Boot > iprobe Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F U-Boot > ping 192.168.253.10 host 192.168.253.10 is alive U-Boot > Signed-off-by: NSergey Kubushyn <ksi@koi8.net> Acked-by: NDirk Behme <dirk.behme@gmail.com> Acked-by: NZach Sadecki <Zach.Sadecki@ripcode.com> Acked-by: NStefan Roese <sr@denx.de>
-
- 27 7月, 2007 1 次提交
-
-
由 Rafal Jaworowski 提交于
The following MPC5121e subsystems are supported: - low-level CPU init - NOR Boot Flash (common CFI driver) - DDR SDRAM - FEC - I2C - Watchdog Signed-off-by: NGrzegorz Bernacki <gjb@semihalf.com> Signed-off-by: NRafal Jaworowski <raj@semihalf.com> Signed-off-by: NJan Wrobel <wrr@semihalf.com>
-
- 13 7月, 2007 1 次提交
-
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
- 11 7月, 2007 1 次提交
-
-
由 TsiChungLiew 提交于
Added mcffec_initialize() in eth_initialize() Signed-off-by: NTsiChungLiew <Tsi-Chung.Liew@freescale.com>
-
- 10 7月, 2007 1 次提交
-
-
由 Jon Loeliger 提交于
Signed-off-by: NJon Loeliger <jdl@freescale.com>
-
- 04 7月, 2007 1 次提交
-
-
由 Jon Loeliger 提交于
This is a compatibility step that allows both the older form and the new form to co-exist for a while until the older can be removed entirely. All transformations are of the form: Before: #if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) After: #if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT) Signed-off-by: NJon Loeliger <jdl@freescale.com>
-
- 23 6月, 2007 1 次提交
-
-
由 Heiko Schocher 提交于
- Show on the Status LEDs, some States of the board. - Get the MAC addresses from the EEProm - use PREBOOT - use the CF on the board. - check the U-Boot image in the Flash with a SHA1 checksum. - use dynamic TLB entries generation for the SDRAM Signed-off-by: NHeiko Schocher <hs@denx.de>
-
- 19 6月, 2007 1 次提交
-
-
由 TsiChung Liew 提交于
Added board/freescale/m5329evb, cpu/mcf532x, drivers/net, drivers/serial, immap_5329.h, m5329.h, mcfrtc.h, include/configs/M5329EVB.h, lib_m68k/interrupts.c, and rtc/mcfrtc.c Modified CREDITS, MAKEFILE, Makefile, README, common/cmd_bdinfo.c, common/cmd_mii.c, include/asm-m68k/byteorder.h, include/asm-m68k/fec.h, include/asm-m68k/io.h, include/asm-m68k/mcftimer.h, include/asm-m68k/mcfuart.h, include/asm-m68k/ptrace.h, include/asm-m68k/u-boot.h, lib_m68k/Makefile, lib_m68k/board.c, lib_m68k/time.c, net/eth.c and rtc/Makefile Signed-off-by: NTsiChung Liew <Tsi-Chung.Liew@freescale.com>
-
- 17 5月, 2007 1 次提交
-
-
由 Kim Phillips 提交于
For all practical u-boot purposes, TSECs don't differ throughout the mpc8[356]xx families; reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECx. Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 14 4月, 2007 1 次提交
-
-
由 Haavard Skinnemoen 提交于
Implement MACB initialization for AVR32 and ATSTK1000, and turn everything on, including the MACB driver. Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
-
- 05 4月, 2007 1 次提交
-
-
由 Aubrey Li 提交于
-
- 29 11月, 2006 1 次提交
-
-
由 Stefan Roese 提交于
This patch adds support for the Prodrive P3M750 (PPC750 & MV64460) and the P3M7448 (MPC7448 & MV64460) PMC modules. Both modules are quite similar and share the same board directory "prodrive/p3mx" and the same config file "p3mx.h". Signed-off-by: NStefan Roese <sr@denx.de>
-
- 04 11月, 2006 1 次提交
-
-
由 Dave Liu 提交于
this patch adds support for the QUICC Engine based UCC gigabit ethernet device.
-
- 02 11月, 2006 1 次提交
-
-
由 roy zang 提交于
The following is a brief description of the Ethernet controller: The Tsi108/9 Ethernet Controller connects Switch Fabric to two independent Gigabit Ethernet ports,E0 and E1. It uses a single Management interface to manage the two physical connection devices (PHYs). Each Ethernet port has its own statistics monitor that tracks and reports key interface statistics. Each port supports a 256-entry hash table for address filtering. In addition, each port is bridged to the Switch Fabric through a 2-Kbyte transmit FIFO and a 4-Kbyte Receive FIFO. Each Ethernet port also has a pair of internal Ethernet DMA channels to support the transmit and receive data flows. The Ethernet DMA channels use descriptors set up in memory, the memory map of the device, and access via the Switch Fabric. The Ethernet Controller?s DMA arbiter handles arbitration for the Switch Fabric. The Controller also has a register businterface for register accesses and status monitor control. The PMD (Physical Media Device) interface operates in MII, GMII, or TBI modes. The MII mode is used for connecting with 10 or 100 Mbit/s PMDs. The GMII and TBI modes are used to connect with Gigabit PMDs. Internal data flows to and from the Ethernet Controller through the Switch Fabric. Each Ethernet port uses its transmit and receive DMA channels to manage data flows through buffer descriptors that are predefined by the system (the descriptors can exist anywhere in the system memory map). These descriptors are data structures that point to buffers filled with data ready to transmit over Ethernet, or they point to empty buffers ready to receive data from Ethernet. Signed-off-by: NAlexandre Bounine <alexandreb@tundra.com> Signed-off-by: NRoy Zang <tie-fei.zang@freescale.com>
-
- 30 5月, 2006 1 次提交
-
-
由 Wolfgang Denk 提交于
- Add IXP4xx NPE ethernet MAC support - Add support for Intel IXDPG425 board - Add support for Prodrive PDNB3 board - Add IRQ support Patch by Stefan Roese, 23 May 2006 [This patch does not include cpu/ixp/npe/IxNpeMicrocode.c which still sufferes from licensing issues. Blame Intel.]
-
- 27 4月, 2006 1 次提交
-
-
由 Jon Loeliger 提交于
-
- 01 12月, 2005 1 次提交
-
-
由 Marian Balakowicz 提交于
ethaddr is assigned). Initialization moved from miiphy_register() to eth_initialize(). Based on initial patch for 4xx platform by Matthias Fuchs.
-
- 30 11月, 2005 1 次提交
-
-
由 Stefan Roese 提交于
- Support for TQM8541/8555 boards added. - Complete rework of TQM8540/8560 support. - Common TQM85xx code now supports all current TQM85xx platforms (TQM8540/8541/8555/8560). - DDR SDRAM size detection added. - CAS latency default values can be overwritten by setting "serial#" to e.g. "ABC0001 casl=25" -> CAS latency 2.5 will be used. If problems are detected with this non default CAS latency, the defualt values will be used instead. - FLASH size detection added. - Moved FCC ethernet driver initialization behind TSEC driver init -> TSEC is first device. Patch by Stefan Roese, 30 Nov 2005
-
- 29 10月, 2005 1 次提交
-
-
由 Marian Balakowicz 提交于
-
- 13 10月, 2005 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 09 10月, 2005 1 次提交
-
-
由 Wolfgang Denk 提交于
Patch by James MacAulay, 07 Oct 2005
-
- 25 9月, 2005 1 次提交
-
-
由 Wolfgang Denk 提交于
Patch by Ara Avanesyan, 24 Feb 2005
-
- 17 8月, 2005 1 次提交
-
-
由 Stefan Roese 提交于
now handling all 4xx cpu's. Patch by Stefan Roese, 16 Aug 2005
-
- 28 7月, 2005 1 次提交
-
-
由 Eran Liberty 提交于
Add support for the Freescale MPC8349ADS board.
-
- 26 7月, 2005 1 次提交
-
-
由 Jon Loeliger 提交于
Implemented support for MPC8548CDS board. Added DDR II support based on SPD values for MPC85xx boards. This roll-up patch also includes bugfies for the previously published patches: DDRII CPO, pre eTSEC, 8548 LBIU, Andy's TSEC, eTSEC 3&4 I/O
-
- 16 5月, 2005 1 次提交
-
-
由 wdenk 提交于
Code cleanup (especially Sorcery / Alaska / Yukon serial driver).
-
- 17 12月, 2004 1 次提交
-
-
由 stroese 提交于
-
- 28 10月, 2004 1 次提交
-
-
由 wdenk 提交于
- add support for MPC8220 CPU - Add support for Alaska and Yukon boards
-
- 10 7月, 2004 1 次提交
-
-
由 wdenk 提交于
Completion of the 8540ADS/8560ADS updates: Fix some PCI and Rapid I/O memory maps, Initialize both TSEC 1 and 2, Initialize SDRAM Update MAINTAINER for 85xx boards and README.mpc85xxads
-
- 09 5月, 2004 1 次提交
-
-
由 wdenk 提交于
on-chip interfaces before external cards.
-
- 19 4月, 2004 1 次提交
-
-
由 wdenk 提交于
Update max RAM size for debris board * Patch by Travis Sawyer, 08 Apr 2004: Add TLB entry for second DIMM slot on ocotea * Patch by Masami Komiya, 08 Apr 2004: add RTL8169 network driver
-
- 16 4月, 2004 1 次提交
-
-
由 wdenk 提交于
add networking support for VLANs (802.1q), and CDP (Cisco Discovery Protocol)
-
- 24 2月, 2004 1 次提交
-
-
由 wdenk 提交于
Add support for NFS for file download * Minor code cleanup
-
- 07 2月, 2004 1 次提交
-
-
由 wdenk 提交于
Add support for IBM PPC440GX. Multiple EMAC Ethernet devices, select MDI port based on enabled EMAC device. Add support for XES Inc <http://www.xes-inc.com> XPedite1000 440GX base PrPMC board.
-
- 03 1月, 2004 1 次提交
-
-
由 wdenk 提交于
Add support for the Marvell DB64360 / DB64460 development boards * Patch by Detlev Zundel, 10 Dec 2003: fix dependency problem in examples/Makefile
-