Signed-off-by: NStefan Kristiansson <stefan.kristiansson@saunalahti.fi>

This board is similar to our tuxx1 target. But on this board there
is only one application specific chip select configured.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Acked-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>

These boards are from a u-boot point of view identical. So collect
the two headerfiles to one, to decrease maintenance.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>

The Medcom is a 16:9 15" terminal that is used for patient infotainment
in hospitals.

Changes in v3:
  * Remove unused implementation of gpio_config_uart().
  * Implement MMC/SD card detection.
  * Drop board_mmc_getcd() which is now implemented by common Tegra2
    code.
  * Add MAINTAINERS entry.

Changes in v2:
  * No longer override the default CONFIG_SYS_TEXT_BASE setting.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Acked-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

The Plutux is a set-top box device based on the Tamonten processor
module. It can be connected to a display via an HDMI output.

Changes in v3:
  * Remove unused implementation of gpio_config_uart().
  * Implement MMC/SD card detection.
  * Drop board_mmc_getcd() which is now implemented by common Tegra2
    code.
  * Add MAINTAINERS entry.

Changes in v2:
  * No longer override the default CONFIG_SYS_TEXT_BASE setting.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Acked-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

The twister board is a development board using
the TAM3517 SOM.

Support for NAND, 2 Ethernet (EMAC and SMC911),
USB (EHCI_OMAP).
Signed-off-by: NStefano Babic <sbabic@denx.de>
CC: Tapani Utrianen <tapani@technexion.com>
CC: Tom Rini <tom.rini@gmail.com>
CC: Sandeep Paulraj <s-paulraj@ti.com>

Add the initial support for Freescale i.MX6Q Armadillo2 board
Support: MMC boot from slot 0/1, debug UART(UART4), usdhc.

There is two MMC slots on the boards:
mmc dev 0 -> connect USDHC3 -> the lower slot on the board,
mmc dev 1 -> connect USDHC4 -> the upper slot on the board,
Signed-off-by: NJason Liu <jason.hui@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: NDirk Behme <dirk.behme@de.bosch.com>

As per new naming convention for Samsung SoC's, all Cortex-A9 and Cortex-A15
based SoC's will be classified under the name Exynos. Cortex-A9 and Cortex-A15
based SoC's will be sub-classified as Exynos4 and Exynos5 respectively.

In order to better adapt and reuse code across various upcoming Samsung Exynos
based boards, all uses of s5pc210 prefix/suffix/directory-names are renamed in
this patch. s5pc210 is renamed as exynos4210 and S5PC210/s5pc210 suffix/prefix
are renamed as exynos4/EXYNOS4.
Signed-off-by: NChander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

Ventana is a board which is very similar to Seaboard. Support it by
re-using board/nvidia/seaboard/seaboard.c with minor run-time conditionals.

v5: Makefile: Use cmd_link_o_target, remove unused clean/distclean targets.
v6: Make gpio_config_uart_seaboard() static.
v7: Add MAINTAINERS entry for Ventana. Tom Warren doesn't have Ventana, so
    he asked me to add myself for this board.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Warren <twarren@nvidia.com>

The eXMeritus HWW-1U-1A unit is a DO-160-certified 13lb 1U chassis
with 3 independent TEMPEST zones.  Two independent P2020 computers may
be found inside each zone.  Complete hardware support is included.

High-level hardware overview:
  * DO-160 certified for passenger aircraft (noncritical)
  * TEMPEST ceritified for RED/BLACK separation
  * 3 zones per chassis, 2 computers per zone (total of 6)
  * Dual-core 1.066GHz P2020 per computer
  * One 2GB DDR2 SO-RDIMM module per computer (upgradable to 4GB)
  * Removable 80GB or 160GB Intel X18-M SSD per computer
  * Front-accessible dual-port E1000E per computer
  * Front-accessible serial console per computer
  * Front-accessible USB port per computer
  * Internal Gigabit crossover within each TEMPEST zone
  * Internal unidirectional fiber links across TEMPEST zones
  * Battery-backed DS1339 I2C RTC on each CPU.

Combined, each 13lb 1U chassis contains 12GB RAM, 12 cores @ 1.066GHz,
12 front-accessible Gigabit Ethernet ports and 960GB of solid-state
storage with a total power consumption of ~200W.

Additional notes:
  * SPD detection is only known to work with the DO-160-certified DIMMs

  * CPU reset is a little quirky due to hardware misfeature.  Proper
    support for the hardware reset mechanism has been left for a later
    patch series to address.
Signed-off-by: NKyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The "rmu" board has long been unmaintained, and is broken.
Remove it.
Signed-off-by: NWolfgang Denk <wd@denx.de>

The BAB7xx boards are almost deceased.  They cause build warnings, an
it's not worth the effort to fix these.  Remove the dead body.
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>

- booting from NOR Flash with direct boot method
- POST support
- LOGBUF support
Signed-off-by: NHeiko Schocher <hs@denx.de>
Cc: Paulraj Sandeep <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Christian Riesch <christian.riesch@omicron.at>

The board is unmaintained and maintainer doesn't respond.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>

The board is unmaintained and maintainer doesn't respond.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>

Add support for the Ethernut 5 open hardware design, based
on Atmel's AT91SAM9XE512 SoC.

V4
 - Fix several coding style issues.
 - Move machine type to config file.
 - Remove use of CONFIG_ATMEL_LEGACY.
Signed-off-by: NTim Schendekehl <tim.schendekehl@egnite.de>

This patch adds support for the LaCie 2Big Network v2 board, based on
the Marvell Kirkwood 6281 SoC.

Additional information is available at:
http://lacie-nas.org/doku.php?id=2big_network_v2Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org>

Signed-off-by: NThomas Weber <weber@corscience.de>

The ecovec board has SH7724, 256MB DDR2-SDRAM, USB,
Ethernet, and more.

This patch supports the following functions:
	- 256MB DDR2-SDRAM
	- USB
	- I2C
	- Ethernet
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

Board support for the Guntermann & Drunck Io64.
Signed-off-by: NDirk Eibach <eibach@gdsys.de>
Signed-off-by: NStefan Roese <sr@denx.de>

This adds support for the Freescale COM Express P2020 board. This board
is similar to the P1_P2_RDB, but has some extra (as well as missing)
peripherals.

Unlike all other mpc85xx boards, it uses a watchdog timeout to reset.
Using the HRESET_REQ register does not work.

This board has no NOR flash, and can only be booted via SD or SPI. This
procedure is documented in Freescale Document Number AN3659 "Booting
from On-Chip ROM (eSDHC or eSPI)." Some alternative documentation is
provided in Freescale Document Number P2020RM "P2020 QorIQ Integrated
Processor Reference Manual" (section 4.5).
Signed-off-by: NIra W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Change my old email address which is no longer valid.
Signed-off-by: NStelian Pop <stelian@popies.net>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

Change my old email address which is no longer valid.
Signed-off-by: NStelian Pop <stelian@popies.net>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

The last maintainer (Eran Man) cannot be reached any more.
Signed-off-by: NWolfgang Denk <wd@denx.de>

This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.

OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.

Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.
Signed-off-by: Nsricharan <r.sricharan@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Cc: Robert Schwebel <robert@schwebel.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>

This contains support for the following components:
- DUART
- MMC
- Both FEC interfaces
- NAND
- I2C (RTC, EEPROM)
- SPI (FLASH)
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>

Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NTom Rini <trini@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Add ADP-AG101P into MAINTAINERS list.
Add ADP-AG101P into boards.cfg.
Signed-off-by: NMacpaul Lin <macpaul@andestech.com>

Add support for the MATRIX VISION mvBlueLYNX-X, an OMAP3-based
intelligent camera.
Signed-off-by: NMichael Jones <michael.jones@matrix-vision.de>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

- DM368 SOC
- booting with spl not with UBL from TI
- before loading u-boot from NAND into RAM, test
  the RAM with the post memory test. If error
  is found, switch all LEDs on and halt system.
- SPI Flash
  Dataflash Typ: M25PE80
- Ethernet DM9161BI
- MMC
- USB
Signed-off-by: NHeiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

This adds basic board support for TT-01 based on
the Bluetechnix i.MX31 SOM. Currently only NOR-Flash
boot is implemented.
Signed-off-by: NHelmut Raiger <helmut.raiger@hale.at>
Acked-by: NStefano Babic <sbabic@denx.de>

The flea3 board is a custom board by CarMediaLab used
in automotive.
Network (FEC), NOR, NAND and SPI are supported.
Signed-off-by: NStefano Babic <sbabic@denx.de>

Add basic support for Calxeda Highbank platform. Only minimal support with
serial and SATA are included.
Signed-off-by: NJason Hobbs <jason.hobbs@calxeda.com>
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>

This patch adds basic support for booting the board.
This patch adds support for the UART necessary to
get to the u-boot prompt.
Signed-off-by: NChandan Nath <chandan.nath@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Copied wholeheartedly from board/Marvell/guruplug and modified to add support
for SPI NOR flash.

CONFIG_MACH_DREAMPLUG defined in include/configs/dreamplug.h until Linus's
kernel.org tree adds it to mach-types.h.  Once it trickles down, the definition
can be removed from include/configs/dreamplug.h.
Signed-off-by: NJason Cooper <u-boot@lakedaemon.net>

The board stopped building some time ago, and the board maintainer
agrtees to drop it - see
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/112674Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>

Add evaluation board "adp-ag101" configuration file adp-ag101.h.
Add adp-ag101.c board config and related settings.
Add board adp-ag101 into boards.cfg
Signed-off-by: NMacpaul Lin <macpaul@andestech.com>

Add support for the qi_lb60 (a.k.a QI Ben NanoNote) clamshell device
from Qi hardware:

http://en.qi-hardware.com/wiki/Ben_NanoNote
http://en.qi-hardware.com/wiki/Main_Page
http://en.wikipedia.org/wiki/Qi_hardware

This Jz4740-based clamshell device does not use NOR flash to boot.
The initial bring-up assumes that U-Boot is directly loaded into SDRAM
using USB boot tool, and starts from 0x80100000.

About USB boot tool
-------------------

Jz4740 is one of the XBurst processors with USB boot functionality
supported.  The CPU can boot from a small ROM in the LSI, initialize
CPU and USB module, then wait for USB commands from the USB host.
We can send 8 KB binary data to the CPU cache using USB boot tool.

USB boot tool is available to the public at Ingenic website.  Also
there is an alternative Debian package named xburst-tools.
Signed-off-by: NXiangfu Liu <xiangfu@openmobilefree.net>
Acked-by: NDaniel <zpxu@ingenic.cn>
Signed-off-by: NShinya Kuribayashi <skuribay@pobox.com>

The EST SBC8260 is over 10 years old, and the SBC8240 older than
that.  With the tiny amount of RAM (by today's standards), there
really isn't anyone interested in running the latest U-boot on
these EOL products anymore.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
CC: jon.diekema@smiths-aerospace.com