Signed-off-by: NTom Rini <trini@konsulko.com>

- micrel, ti PHY fixes
- rtl8169, mtk-eth fixes

STM32 MCUs update:
_ Add MPU region for SPI NOR memory mapped region
_ Add missing QSPI flash compatible for STM32 F7 boards
_ Update spi-tx-bus-width and spi-rx-bus-width properties
_ Add QSPI support for STM32F469 Discovery board

In mt7629-rfb.dts, the phy-handle is a reference to the node phy0, not the
node itself:

	phy-handle = <&phy0>;

	phy0: ethernet-phy@0 {
		reg = <0>;
	}

However the driver used ofnode_find_subnode("phy-handle") to read the node.
It will always fail.

This patch replaces ofnode_find_subnode with dev_read_phandle_with_args to
make sure the node can be read correctly.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NWeijie Gao <weijie.gao@mediatek.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

This version of the RTL-8168 is present on some development boards and
is compatible with this driver. Add support for identifying this version
of the chip so that U-Boot won't complain about it being unknown.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

Implement this callback that allows the MAC address to be set for the
Ethernet card. This is necessary in order for the device to be able to
receive packets for the MAC address that U-Boot advertises.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

There is a need to fill node before clk_output_sel is setup.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Acked-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: <hannes.schmelzer@br-automation.com>

Commit d397f7c4 ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.

This commit contains the following changes:

- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.
Signed-off-by: NJames Byrne <james.byrne@origamienergy.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

Pull request for UEFI sub-system for v2019.07-rc3

The development target for the UEFI sub-system is EBBR compliance. We have
already implemented some further protocols to enable running the UEFI Shell
and the UEFI SCT test suite.

As some boards are severely memory constrained make some of these extras
customizable.

Provide bug fixes. The most prominent ones let us pass the UEFI SCT memory
allocation tests.

- A10 FPGA programming support, Gen5 livetree conversion

- SH2, SH3 removal

Describe that efi_install_fdt() defaults to using the device tree
indicated by environment variable fdtcontroladdr.

ACPI tables and device trees are mutually exclusive.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Move duplicate initialization code to single instance.

Adjust comments of concerned functions.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

The device path to text protocol renders ACPI device nodes incorrectly.

Use capital hexadecimal numbers as shown in the UEFI spec examples.

Always output the optional UID. This matches what UEFI SCT expects and
saves us an `if`.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

UEFI SCT uses this call sequence to determine the current TPL level inside
notification functions:

    OldTpl = BS->RaiseTPL(TPL_HIGH_LEVEL);
    BS->RestoreTPL(OldTpl);

In RestoreTPL() we trigger the notification function of queued events. If
we do not mark the event as non-queued before calling the notification
function, this results in an infinite recursive call sequence.

Mark the event as non-queued before entering the notification function.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Replace unnecessary control structures by using return statements.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

If AllocatePages() is called with AllocateAddress, the UEFI spec requires
to return EFI_NOT_FOUND in case the memory page does not exist.

The UEFI SCT II 2017 spec additionally requires to return EFI_NOT_FOUND if
the page is already allocated.

Check that *Memory refers to an unallocated page.

UEFI SCT II (2017): AllocatePages(), 5.1.2.1.9 - 5.1.2.1.10
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

According to the UEFI AllocatePages() has to return EFI_OUT_OF_RESOURCES if
sufficient memory is not available.

Change the return value.

UEFI SCT II (2017): 3.2.1 AllocatePages(), 5.1.2.1.8
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

When we call FreePages() we essentially add memory to our memory map. We
shouldn't do this for memory that does not exit.

Check if the memory that is to be freed via FreePages() or FreePool() is in
our memory map and is not EFI_CONVENTIONAL_MEMORY.

This check is mandated by the UEFI specification.

Cf. UEFI SCT  II (2017), 3.2.2 FreePages(), 5.1.2.1 - 5.1.2.2
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

According to the UEFI specification UninstallProtocolInteface() has to
return EFI_NOT_FOUND if the interface is not found.

Correct the return value.

Cf. UEFI SCT II spec (2017), 3.3.2 UninstallProtocolInterface(), 5.1.3.2.4
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

efi_search_protocol() already checks that the GUID matches. Don't check
a second time.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

A parameter check in LocateDevicePath() does not match the requirements of
the UEFI spec.

If device is NULL, only return EFI_INVALID_PARAMETER if a matching handle
is found.

Cf. UEFI SCT II specification (2017)3.3.7 LocateDevicePath(), 5.1.3.7.3
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

%s/not buffer/no buffer/
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

The device path to text protocol is not needed for EBBR compliance. So
let's make it a customizable option.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

The Unicode collation protocol is not needed for EBBR compliance. So let's
make it a customizable option.

The Unicode capitalization table is only needed by this protocol. So let it
depend on the Unicode collation protocol.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

No need to mention U-Boot in brief description.
Fix several typos, mention iPXE.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Use if/endif for dependencies to give structure to the configuration menu.

Sort important settings to the top.

Abbreviate the short description of EFI_LOADER_HII.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

If EFI_LOADER_HII is not set, do not unnecessarily compile files for HII
protocols.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Assign include/charset.h to EFI PAYLOAD.

The functions defined in this include are used by the UEFI sub-system.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Correct the description of utf8_utf16_strnlen() and utf8_utf16_strlen() to
reflect that they return u16 count and not byte count.

For these functions and utf16_utf8_strnlen() describe the handling of
invalid code sequences.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Convert 'gpio_dwapb_bind' to iterate over subnodes using livetree
functions (inspired from mt7621_gpio.c).
Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Convert 'socfpga_reset_probe' to use 'dev_read_u32_default'
instead of 'fdtdec_get_int'.
Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Convert 'altera_uart_ofdata_to_platdata' to use 'dev_read_u32_default'
instead of 'fdtdec_get_int' and get rid of DECLARE_GLOBAL_DATA_PTR.
Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Convert 'dw_spi_ofdata_to_platdata' to use 'dev_read_u32_default'
instead of 'fdtdec_get_int' and get rid of DECLARE_GLOBAL_DATA_PTR.
Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Convert 'cadence_spi_ofdata_to_platdata' to use dev_read_* functions to
read driver parameters and 'dev_read_first_subnode'/'ofnode_read_*' to
read flash (child node) parameters.

Tested on socfpga_socrates (socfpga gen5).
Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

The dw-apb timer does not use 'gd', so remove its declaration.
Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Fix SPI flash environment erase size error.

CONFIG_ENV_SECT_SIZE is set to 4KB. Enable CONFIG_SPI_FLASH_USE_4K_SECTORS
to allow erase one environment sector.

Fix error below:

SOCFPGA_STRATIX10 # saveenv
Saving Environment to SPI Flash...
SF: Detected mt25qu02g with page size 256 Bytes, erase size 64 KiB, total 256 MiB
Erasing SPI flash...SF: Erase offset/length not multiple of erase size
Failed (-22)
Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>

Increasing Malloc pool size up to 0x15000 is required to support FAT in SPL
. The result of calculation is come from default max cluster(0x10000) +
others(0x2000) + additional memory for headroom(0x3000).
Signed-off-by: NTien Fong Chee <tien.fong.chee@intel.com>

Update the default configuration file to enable the necessary functionality
the get the kit working.
Signed-off-by: NTien Fong Chee <tien.fong.chee@intel.com>

Add support for loading FPGA bitstream to get DDR up running before
U-Boot is loaded into DDR. Boot device initialization, generic firmware
loader and SPL FAT support are required for this whole mechanism to work.
Signed-off-by: NTien Fong Chee <tien.fong.chee@intel.com>