- 31 8月, 2021 2 次提交
-
-
由 Tom Rini 提交于
- Rename usages of CONFIG_SYS_DEF_EEPROM_ADDR to CONFIG_SYS_I2C_EEPROM_ADDR based on current usage. - Convert CONFIG_SYS_I2C_EEPROM_ADDR, CONFIG_SYS_I2C_EEPROM_ADDR_LEN, CONFIG_SYS_I2C_EEPROM_BUS, CONFIG_CONFIG_SYS_EEPROM_SIZE CONFIG_SYS_EEPROM_PAGE_WRITE_BITS and CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS to Kconfig. We move these symbols around a bit and add appropriate dependencies to them. In some cases, we now add a correct default value as well. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
This converts the following to Kconfig: CONFIG_ID_EEPROM Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 29 7月, 2021 2 次提交
-
-
由 Simon Glass 提交于
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
由 Simon Glass 提交于
Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
- 27 7月, 2021 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 08 7月, 2021 1 次提交
-
-
由 Tom Rini 提交于
The following boards no longer need CONFIG_DM_PCI_COMPAT enabled, so remove that. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 28 6月, 2021 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 12 5月, 2021 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 01 12月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 06 10月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 24 9月, 2020 2 次提交
-
-
由 Ran Wang 提交于
commit 0cfccb54 ("configs: Resync with savedefconfig") removed CONFIG_USB_STORAGE from some powerpc platforms' defconfig files, whicih would block the use case of system loading rootfs from USB drives, add them back. Signed-off-by: NRan Wang <ran.wang_1@nxp.com> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Xiaowei Bao 提交于
Enable the DM ESPI driver in T1024RDB defconfig. Signed-off-by: NXiaowei Bao <xiaowei.bao@nxp.com> Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com> [Rebased] Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 29 7月, 2020 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 28 7月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 11 7月, 2020 1 次提交
-
-
由 Marek Szyprowski 提交于
Move ADDR_MAP related config options from include/configs/*.h to the proper place in lib/Kconfig. This has been done using ./tools/moveconfig.py and manual inspection of the generated changes. This is a preparation to use ADDR_MAP helper on ARM 32bit Raspberry Pi4 board for mapping the PCIe XHCI MMIO, which is above the 4GiB identity mapping limit. Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
- 07 7月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 23 6月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 12 6月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 04 6月, 2020 1 次提交
-
-
由 Madalin Bucur 提交于
Enable DM_ETH on all the defconfigs for the T1024RDB board. Signed-off-by: NMadalin Bucur <madalin.bucur@oss.nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 09 5月, 2020 1 次提交
-
-
由 Ashok Reddy Soma 提交于
Move below defines which are used by mtest utility to Kconfig. CONFIG_SYS_MEMTEST_START CONFIG_SYS_MEMTEST_END Signed-off-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> [trini: Fix kmcoge5ne board, re-run migration as well] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 08 5月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 04 5月, 2020 1 次提交
-
-
由 Biwen Li 提交于
This enables DM_I2C and DM_RTC in T1024RDB defconfigs, except T1024RDB SECURE_BOOT defconfig Signed-off-by: NBiwen Li <biwen.li@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 29 4月, 2020 2 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
This converts the following to Kconfig: CONFIG_PHYLIB CONFIG_BITBANGMII CONFIG_MV88E6352_SWITCH CONFIG_MV88E61XX_SWITCH CONFIG_PHYLIB_10G CONFIG_PHY_AQUANTIA CONFIG_PHY_ATHEROS CONFIG_PHY_BROADCOM CONFIG_PHY_CORTINA CONFIG_PHY_DAVICOM CONFIG_PHY_ET1011C CONFIG_PHY_LXT CONFIG_PHY_MARVELL CONFIG_PHY_MICREL CONFIG_PHY_NATSEMI CONFIG_PHY_REALTEK CONFIG_RTL8211X_PHY_FORCE_MASTER CONFIG_PHY_SMSC CONFIG_PHY_TERANETICS CONFIG_PHY_TI CONFIG_PHY_VITESSE CONFIG_PHY_XILINX Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 23 1月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 23 12月, 2019 1 次提交
-
-
由 Ran Wang 提交于
Signed-off-by: NRan Wang <ran.wang_1@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 05 12月, 2019 2 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Miquel Raynal 提交于
Both symbols must be enabled when there is a raw NAND driver selected. Also enable them when CONFIG_CMD_NAND is selected to avoid breaking things when we'll further rework the MTD dependency description. Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: NBoris Brezillon <boris.brezillon@bootlin.com> [trini: Rebase and migrate a few more boards here] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 25 11月, 2019 1 次提交
-
-
由 Yinbo Zhu 提交于
Enable eSDHC device module for T1024RDB board Signed-off-by: NYinbo Zhu <yinbo.zhu@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 21 11月, 2019 1 次提交
-
-
由 Tom Rini 提交于
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
-
- 23 9月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 28 8月, 2019 1 次提交
-
-
由 Hou Zhiqiang 提交于
Enable the DM PCIe driver in T1024RDB defconfig. Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
- 26 8月, 2019 1 次提交
-
-
由 Hou Zhiqiang 提交于
Add device tree for T1024RDB board and enable CONFIG_OF_CONTROL so that device tree can be compiled. Update board README for device tree usage. Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
-
- 15 6月, 2019 1 次提交
-
-
由 Tom Rini 提交于
The non-CONFIG_SPL_FRAMEWORK SPL used on some PowerPC platforms have a choice between CONFIG_SPL_NAND_BOOT, CONFIG_SPL_MMC_BOOT and CONFIG_SPL_SPI_BOOT. Migrate this to Kconfig Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 27 5月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Move the main symbol for Freescale Fman Ethernet controller option to Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and rename the SPIFLASH one to follow the same format as all of the others. To do this fully we need to migrate CONFIG_QC, do so. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 30 4月, 2019 1 次提交
-
-
由 Simon Goldschmidt 提交于
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com> [trini: Re-run migration] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 26 3月, 2019 1 次提交
-
-
由 Patrick Delaunay 提交于
This converts the following to Kconfig: CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_MODE CONFIG_SF_DEFAULT_SPEED I use moveconfig script and then manual check on generated u-boot.cfg to solve the remaining issue. Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
-
- 14 11月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms that had been enabling it turn it on by hand. This exposed that we had not yet migrated CMD_MTDPARTS fully, so do so now. Fixes: 86dfa556 ("cmd: ubi: Remove useless call to mtdparts_init()") Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 25 10月, 2018 1 次提交
-
-
由 Jeremy Gebben 提交于
The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G. Signed-off-by: NJeremy Gebben <jgebben@sweptlaser.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 20 10月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: NTom Rini <trini@konsulko.com>
-