- 17 8月, 2007 3 次提交
-
-
由 Kim Phillips 提交于
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Kim Phillips 提交于
add board_add_ram_info, to make memory diagnostic output more consistent. u-boot banner output now looks like: DRAM: 256 MB (DDR1, 64-bit, ECC on) and for boards with SDRAM on the local bus, a line such as this is added: SDRAM: 64 MB (local bus) also replaced some magic numbers with their equivalent define names. Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Tony Li 提交于
The patch split the PIB init code from pci.c to a single file board/freescale/common/pq-mds-pib.c And add Qoc3 ATM card support for MPC8360EMDS and MPC832XEMDS board. Signed-off-by Tony Li <tony.li@freescale.com>
-
- 16 8月, 2007 10 次提交
-
-
由 Kim Phillips 提交于
this enables libfdt code by default for the freescale mpc8313erdb, mpc832xemds, mpc8349emds, mpc8349itx and gp boards. Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Kim Phillips 提交于
this adds libfdt support code for the freescale mpc8313erdb, mpc832xemds, mpc8349emds, mpc8349itx, and gp boards. Boards remain compatible with OF_FLAT_TREE. Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Kim Phillips 提交于
also adds common prototypes to include/common.h. Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Kim Phillips 提交于
PCI clocks and QE frequencies weren't being updated, and the core clock was being updated incorrectly. This patch also adds a /memory node if it doesn't already exist prior to update. plus some cosmetic trimming to single line comments. Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Kim Phillips 提交于
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Kim Phillips 提交于
and reorder the existing 83xx maintainers alpha. Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Wolfgang Denk 提交于
-
由 Jon Loeliger 提交于
Remove a leftover in net/tftp.c while we're at it. Signed-off-by: NJon Loeliger <jdl@freescale.com>
-
由 Jon Loeliger 提交于
Minor path corrections needed to ensure buildability. Signed-off-by: NJon Loeliger <jdl@freescale.com>
-
由 Jon Loeliger 提交于
Remove a leftover in net/tftp.c while we're at it. Signed-off-by: NJon Loeliger <jdl@freescale.com>
-
- 15 8月, 2007 6 次提交
-
-
由 Jerry Van Baren 提交于
Commit 073e1b50 "Fix initrd/dtb interaction" put the new code outside of the #if defined(CONFIG_OF_LIBFDT) when it should have gone inside of the conditional. As a result, it broke non-LIBFDT board builds. Also added a missing "not." to the comment. Signed-off-by: NGerald Van Baren <vanbaren@cideas.com>
-
由 Ed Swarthout 提交于
Typically this causes scsi init to corrupt the devlist and break the coninfo command. Fix a compiler size warning. Signed-off-by: NJason Jin <jason.jin@freescale.com> Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com> Acked-by: NAndy Fleming <afleming@freescale.com>
-
由 ksi@koi8.net 提交于
Signed-off-by: NSergey Kubushyn <ksi@koi8.net>
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
-
- 14 8月, 2007 21 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Andy Fleming 提交于
The original code would wrongly relocate the blob to be right before the initrd if it existed. The blob *must* be within CFG_BOOTMAPSZ, if it is defined. So we make two changes: 1) flag the blob for relocation whenever its address is above BOOTMAPSZ 2) If the blob is being relocated, relocate it before kbd, not initrd Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
由 Peter Pearse 提交于
-
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
When CFG_POST_ETHER_EXT_LOOPBACK is defined, the ethernet POST is not done using an internal loopback connection, but by assuming that an external loopback connector is plugged into the board. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Peter Pearse 提交于
-
由 Peter Pearse 提交于
-
由 Peter Pearse 提交于
-
由 Peter Pearse 提交于
-
由 Peter Pearse 提交于
Merge to two at45.c files into a common file, split to at45.c and spi.c Fix spelling error in DM9161 PHY Support. Initialize at91rm9200 board (and set LED). Add PIO control for at91rm9200dk LEDs and Mux. Change dataflash partition boundaries to be compatible with Linux 2.6. Signed-off-by: NPeter Pearse <peter.pearse@arm.com> Signed-off-by: NUlf Samuelsson <ulf@atmel.com>
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Randy Vinson 提交于
The PCI ID select values on the Arcadia main board differ depending on the version of the hardware. The standard configuration supports Rev 3.1. The legacy target supports Rev 2.x. Signed-off-by Randy Vinson <rvinson@mvista.com>
-
由 Andy Fleming 提交于
Author: Randy Vinson <rvinson@linuxbox.(none)> Enable the PCI-to-ISA bridge in the VIA Southbridge located on the Arcadia main board. Signed-off-by: NRandy Vinson <rvinson@mvista.com> Signed-off-by: NYork Sun <yorksun@freescale.com>
-
由 Andy Fleming 提交于
Signed-off-by: NHaiying Wang <Haiying.Wang@freescale.com> Signed-off-by: NAndy Fleming <afleming@freescale.com>
-