This command is not more depending on fuse command, but have
direct access to BSEC misc driver, so the dependency with
can be removed CMD_FUSE
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Add support of RAM target in flashlayout to load kernel image
("system") and device tree ("filesystem") in DDR with DFU and
start these images.

The flashlayout.tsv is:

-	0x01	fsbl		Binary		none	0x00000000	tf-a.stm32
-	0x03	ssbl		Binary		none	0x00000000	u-boot.stm32
P	0x10	kernel		System		ram0	0xC2000000	uImage.bin
P	0x11	dtb		FileSystem	ram0	0xC4000000	dtb.bin
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Support an U-Boot script included in uimage instead of flashlayout file
(text file in tsv format).

This feature is used to execute this script directly when U-Boot is
loaded in DDR (for update without STM32CubeProgrammer for example).

A simple example with dfu-util only is:

$> echo "dfu 0" > script.cmd
$> mkimage -C none -A arm -T script -d script.cmd script.uimg
$> mkimage -T stm32image -a 0xC0000000 -e 0xC0000000 -d script.uimg \
  script.stm32

$> dfu-util -d 0483:df11 -a 1 -D tf-a.stm32
$> dfu-util -d 0483:df11 -a 0 -D script.stm32
$> dfu-util -d 0483:df11 -a 0 -D u-boot.stm32
$> dfu-util -d 0483:df11 -a 0 -e

Then you can used dfu-utils to update your device

To increase speed, you can also switch to fastboot protocol with:
  echo "fastboot 0" > script.cmd
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Enable the videoconsole during the stm32prog command execution
to have information without UART.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Add a support of UART, using the same protocol than MCU STM32.

See "AN5275: USB DFU/USART protocols used in STM32MP1 Series
bootloaders" for details.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Add a virtual partition to update the pmic non volatile memory.
(on ST board, STPMIC1).
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Add a virtual partition to update the STM32MP15x OTP based
on SMC service provided by TF-A.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Add support for delete option 'D' in flashlayout for
full device or for partitions
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

For reliability of boot from NAND/SPI-NAND (with read-disturb issue)
the SSBL can be present several time, when it is indicated in the
flashlayout with "Binary(X)".
The received binary is copied X times by U-Boot on the target.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Dynamically adapt the MTD partitions in NOR/NAND/SPI-NAND when stm32prog
command detects in the parsed flash layout files:
- a fsbl partition in NOR.
- a tee partition in NOR/NAND/SPI-NAND
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Add support of MTD device (DFU_MTD backend) for
NOR, NAND or SPI-NAND target.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Add support of partial update, update only some partitions,
and check the coherence of the layout with the existing GPT
partitions (offset and size).
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Add support of eMMC device boot partition with
part_id = -1 for offset="boot1"
     or = -2 for offset="boot2"

The stm32prog command configures the MMC DFU backend with "mmcpart"
and configure the eMMC (command "mmc bootbus" and "mmc partconf")
when the update is done.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Add support of MMC device (based on DFU_MMC backend)
for SD card and eMMC update.

Create a GPT partitioning on the device.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Build the list of device and of partition with
a tab separated value file with a stm32 header: the FlashLayout.tsv
(https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout)
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Add a specific command stm32prog for STM32MP soc family
witch allows to program the boot devices with the tool
STM32CubeProgrammer (http://www.st.com/STM32CubeProg).

This command uses the same UART STM32 protocol than MCU
STM32 with or USB with DFU protocol v1.1 (ithe MCU ST
extension are no supported).

The executed actions are based on a tab separated value file
with a stm32 header, the FlashLayout file
(https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout).

This file is parsed by the U-Boot command to:
- initialize the devices
- create the partition table on each device
- initialize the DFU backend to access to not volatile memory
  (NOR/NAND/SD/eMMC) or to virtual device (OTP/PMIC)

Up to STM32PROG_MAX_DEV (5) devices can be updated with a FlashLayout.

The communication between U-Boot and STM32CubeProgrammer is done with
the specific alternate configuration (see "AN5275: USB DFU/USART protocols
used in STM32MP1 Series bootloaders" for details).

The command stm32prog is executed when a boot from USB is detected
(selected with bootpins) and we can program the boot devices with
a simple command (on Windows or Linux):

PC $>  STM32_Programmer_CLI -c port=usb1 -w flaslayout.tsv

1/ the ROM code loads TF-A in embedded RAM (DFU or uart)
2/ TF-A loads flashlayout file and U-Boot in DDR (DFU or uart)
3/ U-Boot executes the stm32prog command (DFU or uart)
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Add a function get_cpu_dev to get the DEV_ID present
in DBGMCU_IDC register.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Add prototype for function dfu_transaction_initiate and
dfu_transaction_cleanup to avoid warning with W=1.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Add a function g_dnl_set_product to change the Product string used in USB
enumeration in any command based on download gadget.

If the function is called with NULL pointer, the product string is set to
the default value (product[] = "USB download gadget").
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Update stm32mp1 board documentation with new management of MMC and
MTD partitions and new PID df11.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Dynamically adapt the MTD partitions in NAND and SPI-NAND when boot from
NOR or NAND/SPI-NAND is detected.

This patch avoids to define the save MTD partition name for NOR and NAND
devices and issue with latest kernel: only the needed MTD partitions
are defined.

For boot from NOR
1/ bootloader (TF-A, U-Boot and OP-TE) in NOR
2/ one large UBI partition in NAND

For boot from NAND
1/ bootloader (TF-A, U-Boot and OP-TE) in MTD raw partition
2/ one large UBI partition
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Manage BOOT_FLASH_SPINAND, with boot_device="spi-nand"
and treat this value in bootcmd_stm32mp.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

As the op-tee presence is detected by U-boot, the stm32mp15_optee_defconfig
is identical to stm32mp15_trusted_defconfig and can be removed.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Save and use the FDT address provided by TF-A in r2 at boot time
(it is NT_FW_CONFIG = Non Trusted Firmware configuration file)

Address is saved in save_boot_params(), called by start.S
and the used DTB is gd->fdt_blob = board_fdt_blob_setup().

If dtb is not provided or invalid, U-Boot use as fallback
the builtin DTB.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Activate OP-TEE driver for trusted and optee defconfig.

This driver allows detection of TEE presence for boot from flash;
CONFIG_STM32MP1_OPTEE is also removed.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Add reserve memory for OP-TEE in U-Boot and in kernel device tree:
- no more reduce the DDR size in "memory" node:
  CONFIG_SYS_MEM_TOP_HIDE is no more used
- U-Boot device-tree defines the needed "reserved-memory" for OP-TEE
  and U-Boot should not use this reserved memory: board_get_usable_ram_top
  use lmb lib to found the first free region, the not reserved
  memory, enough to relocate U-Boot: the needed size of U-Boot
  is estimated with gd->mon_len + CONFIG_SYS_MALLOC_LEN.
- the optee node ("optee@...": firmware with compatible "linaro,optee-tz")
  and the associated "reserved-memory" are deactivated in kernel device
  tree when OP-TEE is not detected by U-Boot to prevent kernel issue
  (memory is reserved but not used, optee driver probe failed).
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

This patch reduces the stm32mp1 environment size and builds
dynamically the MTD partitions with information from defconfig
(CONFIG_MTDPARTS_...).
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

This patch reduces the stm32mp1 environment size and
builds dynamically the DFU board configuration with gpt
and mtd partitions and information from defconfig
(CONFIG_DFU_ALT_RAM0).
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Move the stm32mp1 common code set_dfu_alt_info() in common directory,
this patch reduce the maintenance effort on this generic part (not board
dependent).
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

Move the stm32mp1 common code board_get_mtdparts() in common directory,
this patch reduce the maintenance effort on this generic part (not board
dependent).
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>

The DHCOR board does exist in multiple variants with different DDR3
DRAM sizes. To cater for all of them, implement DDR3 code handling.
There are two GPIOs which code the DRAM size populated on the SoM,
read them out and use the value to pick the correct DDR3 config.
Reviewed-by: NPatrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>

Adjust the DDR configuration dtsi such that they only generate the
DRAM configuration node, the DDR controller node is moved into the
stm32mp157-u-boot.dtsi itself. This permits including multiple DDR
configuration dtsi files in board DT.
Reviewed-by: NPatrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>

Add support for multiple DRAM configuration subnodes, while retaining
the support for a single flat DRAM configuration node. This is useful
on systems which can be manufactured in multiple configurations and
where the DRAM configuration can be determined at runtime.

The code is augmented by a function which can be overridden on board
level, allowing a match on the configuration node name, very much like
the fitImage configuration node name matching works. The default match
is on the single top-level DRAM configuration, if matching on subnodes
is required, then this board_stm32mp1_ddr_config_name_match() must be
overridden.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>

The AV96 board does exist in multiple variants. To cater for all of
them, implement board code handling. There are two GPIOs which code
the type of the board, read them out and use the value to pick the
correct device tree from an fitImage.
Reviewed-by: NPatrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Change-Id: Iddb330b9a66500495885457cbe17edc0eacaaf43

Add weak implementation of board_early_init_f() hook into the
STM32MP1 SPL. This can be used to read out e.g. configuration
straps before initializing the DRAM.
Reviewed-by: NPatrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>

Add default U-Boot configuration for the DHCOR SoM on AV96 board.
Reviewed-by: NPatrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>

- Two DWC3 fixes

- Enable USB Host for Odroid-C2 board
- Add Open-Drain/Open-Source emulation in GPIO uclass

Xilinx Versal platform uses dwc3 and hence its compatible string
needs to be added to dwc3 glue ids.
Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.

Reference from below Linux commit,

commit <00fe081dc3a3> ("usb: dwc3: add dis_del_phy_power_chg_quirk")

Cc: Marek Vasut <marex@denx.de>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>