AM4372 uses PL310 L2 Cache. Enable the configs for the same.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Use ti_armv7_common.h config file to inclde the common
configs.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Patch f33b9bd3
[arm: omap3: Enable clocks for peripherals only if they are used]
breaks SPL booting on Beagleboard. Since some gpio input's are
read to detect the board revision. But with this patch above, the
clocks to the GPIO subsystems are not enabled per default any more.
The GPIO banks need to be configured specifically now.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>

The PXA incorrectly uses CONFIG_SYS_HZ, which should be 1000 across
U-Boot. Fix this.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>

Add support for the new Tamonten™ NG platform from Avionic Design.
Currently only I2C, MMC, USB and ethernet have been tested.
Signed-off-by: NAlban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTom Warren <twarren@nvidia.com>

Fix the timeout issue after running "bootp" command in u-boot
console. For example you see "EHCI timed out on TD- token=0x...".
TXFIFOTHRES bits of TXFILLTUNING register should be set to 0x10
after a controller reset and before RUN bit is set
(per technical reference manual).
Signed-off-by: NJim Lin <jilin@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NTom Warren <twarren@nvidia.com>

DT kernel requires CONFIG_OF_LIBFDT. 'bootm' needs to know DT location.
In addition, fix kernel console device and enable U-Boot long help.
Signed-off-by: NSergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>

Initial configuration has worng address of the second chip.
There is an alias for the 1st chip at 0x02000000 in earlier
verions of LP-8x4x, so the boot normally.

However, new LP-8x4xs have a bigger 1st flash chip, and hang on
boot without this patch.
Signed-off-by: NSergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>

Signed-off-by: NSergei Ianovich <ynvich@gmail.com>
CC: Marek Vasut <marex@denx.de>

Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

This supports sh_i2c on koelsch board.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

The koelsch board has one sh-ether device.
This supports sh-ether.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

The lager board uses I2C for reset.
ned-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

The lager board has I2C for rcar.
This supports I2C for rcar on lager board.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

The lager board has one sh-ether device.
This supports sh-ether.
Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, move the
CONFIG_SYS_NO_FLASH to proper position, then we don't need to undef
these two commands.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

remove unneeded #undef for at91sam9x5ek board.
Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

This patch makes the following updates to the cm_t35 config file:
- Replace "ttyS" in default environment kernel bootargs with the new "ttyO"
  notation.
- Remove "omapfb.debug=y" from default environment kernel bootargs.
- Define a minimal power-on delay for USB hub ports so that slow-to-power-on USB
  sticks will have enough time to become responsive.
- Add support for bootz command
- ulpi_reset is not necessary and always fails with the following error message:
  "ULPI: ulpi_reset: failed writing reset bit"
  So, remove it.

Cc: Tom Rini <trini@ti.com>
Signed-off-by: NNikita Kiryanov <nikita@compulab.co.il>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
Acked-by: NStefan Roese <sr@denx.de>

Pin 30 is connected to PHY's RESET# signal, so it must be
put to high. Otherwise PHY won't be found via MDIO interface.
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>

commit 16297cfb
Author: Mateusz Zalega <m.zalega@samsung.com>
Date:   Fri Oct 4 19:22:26 2013 +0200

    usb: new board-specific USB init interface

introduced a new parameter to the dfu command. Adapt the default environment
for the siemens boards.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>

To make managing the environment easier, add DFUARGS to
CONFIG_EXTRA_ENV_SETTINGS.  Then we set DFUARGS down in the DFU part of
the file, and include (or not) the NAND part, based on if NAND is set.
Signed-off-by: NTom Rini <trini@ti.com>

Add SPL U-Boot support to replace x-loader on the Compulab cm_t35
board. Currently only the 256MiB SDRAM board versions are supported.

Tested by booting via MMC and NAND.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: NIgor Grinberg <grinberg@compulab.co.il>

The memory size is autodetected and is passed to the Linux kernel
either via ATAGs or device-tree (dtb). So there is no need to
pass it via the bootargs.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>

Add SPL support for the Technexion TAO3530 SOM to replace
x-loader. Tested with the Thunder baseboard. Currently this is
only tested with the TAO3530 SOM revision (Ax/Bx).

Tested by booting via MMC and NAND.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>

Add support for TechNexion TAO3530 SoM

This patch has been posted quite a long time ago. I ported it to
the latest mainline U-Boot version. With some additional cleanup
and enhancements.
Signed-off-by: NTapani Utriainen <tapani@technexion.com>
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>

With the current scenario SPL size is being overlapped with the public
stack and not allowing any OMAP4 device to boot. So the suggestion came
up was to move the TEXT_BASE down to non-HS limit. Fixing the same and
also moving the SRAM_SCRATCH_SPACE_ADDR up to the end of image
downloadable area.
Discussion on this can be seen here:
https://www.mail-archive.com/u-boot@lists.denx.de/msg127147.html

Tested on OMAP4460 PANDA.
Reported-by: NChao Xu <caesarxuchao@gmail.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Signed-off-by: NIan Campbell <ijc@hellion.org.uk>
Cc: albert.u.boot@aribaud.net

We want to test SPI flash code in the sandbox, so enable the new drivers and
the 'sf test' command.

This command is used to validate the sandbox SPI / SPI flash implementation,
so enable it.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NSimon Glass <sjg@chromium.org>

This allows us to put the SPI flash chip inside the SPI interface node,
with U-Boot finding the correct bus and chip select automatically.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Add support for USB-A9263 board manufactured by Calao Systems
(http://www.calao-systems.com/).
Code is based on old U-Boot sources (2010.09) released by Calao.
Signed-off-by: NMateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

enable support for the siemens AT91SAM9G20 based board corvus.
Signed-off-by: NBoris Schmidt <boris.schmidt@siemens.com>
Reviewed-by: NHeiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

enable support for the siemens AT91SAM9G20 based boards taurus
and axm.
Signed-off-by: NRoger Meier <r.meier@siemens.com>
Reviewed-by: NHeiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Jens Scharsig (BuS Elektronik)<esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik)<esw@bus-elektronik.de>
Acked-by: NScott Wood <scottwood@freescale.com>

Faraday FTSDC021 is a controller which is compliant with
SDHCI v3.0, SDIO v2.0 and MMC v4.3.

However this driver is only verified with SD memory cards.
Signed-off-by: NKuo-Jung Su <dantesu@faraday-tech.com>
Acked-by: NPantelis Antoniou <panto@antoniou-consulting.com>
CC: Andy Fleming <afleming@gmail.com>

dw-mmc.c is the general driver file.
So, remove the exynos specific code at dw-mmc.c.
Instead, exynos specific cod can be move into exynos-dw_mmc.c.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NAlexey Brodkin <abrodkin@synopsys.com>
Acked-by: NPantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: NMinkyu Kang <mk7.kang@samsung.com>

Signed-off-by: NTom Rini <trini@ti.com>

Fixes this error message when USB is started.
"ULPI: ulpi_reset: failed writing reset bit"

It is pointless to manually reset the ULPI as the USB Host
Reset and PHY RESET line should take care of that.
Reported-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NStefan Roese <sr@denx.de>
Signed-off-by: NRoger Quadros <rogerq@ti.com>

Fixes this error message when USB is started.
"ULPI: ulpi_reset: failed writing reset bit"

It is pointless to manually reset the ULPI as the USB Host
Reset and PHY RESET line should take care of that.
Reported-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NStefan Roese <sr@denx.de>
Signed-off-by: NRoger Quadros <rogerq@ti.com>

arndale board is booted from mmc
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Inderpal Singh <inderpal.singh@linaro.org>