Signed-off-by: NLuca Ceresoli <luca.ceresoli@comelit.it>

Currently, some linker scripts are found by common code in config.mk.
Some are found using CONFIG_SYS_LDSCRIPT, but the code for that is
sometimes in arch config.mk and sometimes in board config.mk.  Some
are found using an arch-specific rule for looking in CPUDIR, etc.

Further, the powerpc config.mk rule relied on CONFIG_NAND_SPL
when it really wanted CONFIG_NAND_U_BOOT -- which covered up the fact
that not all NAND_U_BOOT builds actually wanted CPUDIR/u-boot-nand.lds.

Replace all of this -- except for a handful of boards that are actually
selecting a linker script in a unique way -- with centralized ldscript
finding.

If board code specifies LDSCRIPT, that will be used.
Otherwise, if CONFIG_SYS_LDSCRIPT is specified, that will be used.

If neither of these are specified, then the central config.mk will
check for the existence of the following, in order:

$(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/$(CPUDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/board/$(BOARDDIR)/u-boot.lds
$(TOPDIR)/$(CPUDIR)/u-boot.lds

Some boards (sc3, cm5200, munices) provided their own u-boot.lds that
were dead code, because they were overridden by a CPUDIR u-boot.lds under
the old powerpc rules.  These boards' own u-boot.lds have bitrotted and
no longer work -- these lds files have been removed.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Tested-by: NGraeme Russ <graeme.russ@gmail.com>

Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>

In order to support boardId / hwkey lists, the u-boot default
environment has been updated: Added a script checkboardidlist
which checks the list of boardId / hwkey if the boadrId / hwkey
of the IVM is included in that list. This feature is used if you
got different HW variants but you only want to create one boot
package. E.g. supx5 board series.
Signed-off-by: NThomas Herzmann <thomas.herzmann@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>

Add:
  - introduce "bootrunner" environment variable
    This allows to execute consecutive different commands
    specified in the list "subbootcmd". If one command fails
    the command serie will stop.
  - introduce environment variable "develop", "ramfs" and "release"
    Each variable is one way to boot our linux. "develop" is for
    development purpose and boots the SW via NFS. "release" is for
    booting the linux image from flash, "ramfs" allows to load an SW
    image via tftp into ram and executes from there
  - introduce "addmem" variable, this command adds the used memory
    for linux to the bootargs
  - introduce "addvar" variable, this command adress for the /var
    directory to the kernel command line
  - introduce "setramfspram" and "setrootfsaddr" these calculation
    were done if "ramfs" was used (only for debugging)
  - introduce "tftpramfs" used for "ramfs" to load the image into
    RAM (only for debugging)
Remove unneeded stuff:
   - CONFIG_IO_MUXING is obsolete for keymile boards
   - CONFIG_KM_DEF_ENV_PRIVATE is also obsolete
   - define CONFIG_SYS_TEXT_BASE in board configs only
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>

This patch adds last_stage_init to all keymile boards. And
in the last stage init some environment variables for u-boot
were set. Currently these are pnvramaddr, pram and var address.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>

Normaly the PIGGY_MAC_ADRESS can be read directly from the
IVM on keymile boards. On mgcoge3 it differs. Because there
are two piggy boards deployed the second MAC adress must be
calculated with the IVM mac adress and an offset. This patch
allows to set such a offset in the board config.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Heiko Schocher <hs@denx.de>

define KM_IVM_BUS and KM_ENV_BUS macros
 KM_IVM_BUS is used to define the EEprom_ivm environment variable.
 These macros allow the reuse of these I2C addresses in other code
 locations.

remove unneeded code
  On first HW versions the BOCO FPGA was behind a MUX device. These
  HW versions are not supported anymore. And therefore this code can
  be removed.

added LED initialization for SUEN3
  The bootstat LED required to be initialized so to have a green
  colour after start-up.

define CONFIG_SYS_TEXT_BASE
  This is needed by the relocation code and is not the same for
  our ARM BEC and thus needs to be defined.

remove memsize variable
  An environment variable for memsize is not needed.
  this can be get via the board info struct.

remove unneeded double access to bi_dram[i].size field
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NLuca Haab <luca.haab@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

This patch fix the i2c deblocking facility with the i2c HW-Controller.
The required delays for byte reading, the enhanced criteria for stop
the dummy read and required 5 start/stop sequences are added.

Add i2c deblocking before ivm eeprom read.

Improve i2c deblocking sequence by respecting stop hold time.

Cleaned function for deblocking. Have now one function i2c_make_abort()
available for bitbang, mpc82xx and mpc83xx harware controller.
Signed-off-by: NStefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

For the kmsupx5 a new header file was introduced km8321-common.h.
Now the common stuff from tuxa1, tuda1 and suvd3 was removed and
the new header file included.

The defines CONFIG_SYS_PIGGY_BASE and CONFIG_SYS_PIGGY_SIZE are
confusing. Because they actually describe the KMBEC FPGA values.
The KMBEC FPGA can be PRIO on kmeter1 or upio on mgcoge. Therefore
all the defines were renamed.

remove unneeded variable CONFIG_KM_DEF_NETDEV, as it is
already declared in keymile-common.h
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

These new values are:
- enables UART0 and UART1 pins in MPP
- define some L2 cache settings
- changes a SDRAM timing to better fit the hardware
- removed three writes that were the same as the reset values
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>

This patch renames the suen3 defines and functions to KM_KIRKWOOD
which is more generic and more precise, because these values
and functions where used by all suenX boards and not only suen3.
Signed-off-by: NLukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

The Keymile SUPx5 board series is based on a PBEC8321 but
contains an additional PBUS FPGA (LPXF) on local bus CS2.
Signed-off-by: NThomas Reufer <thomas.reufer@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>

First step for a cleanup of all header files for km8321 boards.
Signed-off-by: NThomas Reufer <thomas.reufer@keymile.com>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>

The mgcoge2 board from keymile deploys two different processors.
An ARM based Kirkwood for the "unit" part of the SW and a PPC for
the "ne" part of the SW. Therefore in Linux and U-Boot the names
for the board are mgcoge2un and mgcoge2ne. This patch adds the
mgcoge2ne part of the board. The ppc part of mgboge2 is quite
similar to mgcoge, therefore a generic header km82xx-common.h
was introduced to collect all similiarities. Currently the only
difference is that mgcoge2ne has a 64 MB numonyx NOR flash with
a single die. The mgcoge has a dual die flash 2*32MB from spansion.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

The Kirwood based SUEN8 board from Keymile is at this stage
the same than the suen3 board. This patch adds the board
support for the suen8.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

This board is similar to keymile suen3.
Signed-off-by: NClive Stubbings <clive.stubbings@xentech.co.uk>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: NLukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: NLukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

- serial console on UART1
- Ethernet RMII over UCC4
- PHY SMSC LAN8700
- 64MB Flash
- 128 MB DDR2 RAM
- I2C
- bootcount

This board is similiar to the kmeter1 (8360) board,
so common config options are extracted into the
include/configs/km83xx-common.h file.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

This patch reworks all headerfiles for keymile boards. Furthermore
the environment variables are refactored.

Changes:
  - introduce km-powerpc.h file and extract ppc specific parts to it
  - move ARM specific options and vaiables to km_arm.h
  - sort the environment variables to logical groups
  - enhance the description of the environment variables
  - remove KM specific HW key and board id from kernel command line
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

- adapt copyright string
- change bootdelay to 2 seconds
- set max number of command args to 32
- set I/O buffer size to 512
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

- use I/O accessors
  -> For accessing the FPGA therefore a struct km_bec_fpga
     is introduced.
- no longer externs needed
- to defines, that only select functions, don;t assign a
  numeric value
- Codingstyle changes to prevent checkpatch errors/warnings
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>

The MACH_TYPE SUEN3 is now to specific for keymile boards, because
other boards similar to suen3 will follow. So the MACH_SUEN3 was renamed
to MACH_KM_KIRKWOOD.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>

add following functions to common.h, to prevent
extern declarations:

void disable_addr_trans(void);
void enable_addr_trans(void);
void ddr_enable_ecc(unsigned int dram_size);
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

Signed-off-by: NThomas Chou <thomas@wytron.com.tw>

For freescale i.MX53 eSDHCv2, when using CMD12, cmdtype need
to be set to ABORT, otherwise, next read command will hang.

This is a software Software Restrictions in i.MX53 reference manual:

29.7.8 Multi-block Read
For pre-defined multi-block read operation, that is,the number of blocks
to read has been defined by previous CMD23 for MMC, or pre-defined number
of blocks in CMD53 for SDIO/SDCombo,or whatever multi-block read without
abort command at card side, an abort command, either automatic or manual
CMD12/CMD52, is still required by ESDHC after the pre-defined number of
blocks are done, to drive the internal state machine to idle mode. In this
case, the card may not respond to this extra abort command and ESDHC will
get Response Timeout.  It is recommended to manually send an abort command
with RSPTYP[1:0] both bits cleared.
Signed-off-by: NJason Liu <jason.hui@linaro.org>

Signed-off-by: NJohn Rigby <john.rigby@linaro.org>

Make existing field b_max field in struct mmc unconditional
and use it instead of CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_bread
and mmc_bwrite.

Initialize b_max to CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_register
if it has not been initialized by the hw driver.

Initialize b_max to 0 in all callers to mmc_register.
Signed-off-by: NJohn Rigby <john.rigby@linaro.org>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

As Andy Fleming suggested, we can call mmc_init() in mmc_spi command.
So that we don't need to run mmcinfo command next.
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>

Added the board specific definitions to use the MMCI device.
Signed-off-by: NMatt Waddel <matt.waddel@linaro.org>

Add support for the ARM PrimeCell MultiMedia Interface - PL180.
Ported from original device driver written by ST-Ericsson.
Signed-off-by: NMatt Waddel <matt.waddel@linaro.org>

Use the 'video-mode' environment variable (for Freescale chips that have a
DIU display controller) to designate the full video configuration.  Previously,
the DIU driver used the 'monitor' variable, and it was used only to determine
the output video port.

The old definition of the "monitor" environment variable only determines
which video port to use for output.  This variable was set to a number (0,
1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port.  The
resolution was hard-coded into board-specific code.  The Linux command-line
arguments needed to be hard-coded to the proper video definition string.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

Add function video_get_video_mode(), which parses the "video-mode" environment
variable and returns each of its components.  The format matches the video=
command-line option used for Linux:

	video-mode=<driver>:<xres>x<yres>-<depth>@<freq><,option=string>

	<driver> The video driver, ignored by U-Boot
	<xres> The X resolution (in pixels) to use.
	<yres> The Y resolution (in pixels) to use.
	<depth> The color depth (in bits) to use.
	<freq> The frequency (in Hz) to use.
	<options> A comma-separated list of device-specific options
Signed-off-by: NTimur Tabi <timur@freescale.com>

There seems to be tools producing incorrect 'end of bitmap data'
markers '0100' in a RLE bitmap. Drawing such bitmaps can result
in overwriting memory above the frame buffer. E.g. on MPC5121e
based boards this memory can contain U-Boot environment.

We may not rely on the correct end of bitmap data marker 0001
only, but also have to check whether we are going to draw a
valid frame buffer scan line.

The patch provides a fix by maintaining a pixel counter
which is incremented by the amount of pixels we are going
to draw. If the counter exceeds frame buffer pixels limit
we stop the drawing with the error message.
Reported-by: NMichael Weiss <michael.weiss@ifm.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Tested-by: NAnatolij Gustschin <agust@denx.de>

The following boards gain device tree support with this patch:

ca9x4_ct_vxp - Versatile Express

i.mx5 boards:
efikamx
mx51evk
mx53evk

OMAP boards:
devkit8000
igep0020
igep0030
omap3_overo
omap3_pandora
omap4_sdp3430
omap3_zoom1
omap3_zoom2
omap4_panda
omap4_sdp4430

Tegra boards:
Harmony
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

Deblock i2c bus when switching to another i2c bus, if using
i2c_set_bus_num().
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>