- 06 12月, 2013 2 次提交
-
-
由 Minkyu Kang 提交于
arndale board is booted from mmc Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net> Cc: Inderpal Singh <inderpal.singh@linaro.org>
-
由 Minkyu Kang 提交于
This patch fix following errors and warnings spl_boot.c: In function 'exynos_spi_copy': spl_boot.c:111:49: error: 'CONFIG_ENV_SPI_BASE' undeclared (first use in this function) spl_boot.c:111:49: note: each undeclared identifier is reported only once for each function it appears in spl_boot.c:142:2: error: 'SPI_FLASH_UBOOT_POS' undeclared (first use in this function) spl_boot.c: In function 'copy_uboot_to_ram': spl_boot.c:189:28: warning: unused variable 'param' [-Wunused-variable] spl_boot.c: At top level: spl_boot.c:107:13: warning: 'exynos_spi_copy' defined but not used [-Wunused-function] Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com> Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
-
- 05 12月, 2013 2 次提交
-
-
由 Jaehoon Chung 提交于
These defines didn't use anywhere. Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com> Acked-by: NAlexey Brodkin <abrodkin@synopsys.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Jaehoon Chung 提交于
The "int" type is right. Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
- 03 12月, 2013 8 次提交
-
-
由 Piotr Wilczek 提交于
This patch updates Tizen partions layout. Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Piotr Wilczek 提交于
This patch use 'samsung_get_base' common functions to access registers. Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Piotr Wilczek 提交于
In this patch variable names are used instead of hardcoded names Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Piotr Wilczek 提交于
Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Rajeshwari Shinde 提交于
This patch implements a custom spi_copy funtion to copy u-boot from SF to RAM. This is faster then iROM spi_copy funtion as this runs spi at 50Mhz and also in WORD mode of operation. Changed a printf in pinmux.c to debug just to avoid the compilation error in SPL. Signed-off-by: NAlim Akhtar <alim.akhtar@samsung.com> Signed-off-by: NTom Wai-Hong Tam <waihong@chromium.org> Signed-off-by: NRajeshwari S Shinde <rajeshwari.s@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Minkyu Kang 提交于
res3 should be 4bytes Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com> Cc: Dominik Klein <dominik.klein@gmx.com>
-
由 Jaehoon Chung 提交于
Fix the set_mmc_clk() for exnos4x12. If board is exynos4x12, mmc clock should be set to wrong value. Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Przemyslaw Marczak 提交于
Signed-off-by: NPrzemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
- 02 12月, 2013 3 次提交
-
-
由 Piotr Wilczek 提交于
Trats2 config is updated to support DFU mode. Malloc pool must be increased for DFU buffer allocation. Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Piotr Wilczek 提交于
This patch adds support for USB and enables 'ums' command on Trats2 board. Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Acked-by: NJaehoon Chung <jh80.chung@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Piotr Wilczek 提交于
This patch add new defines for usb phy for Exynos4x12. Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
- 29 11月, 2013 1 次提交
-
-
由 Luka Perkov 提交于
The SPI section is already defined in this file (lines 268-288) so we can remove the duplicate definitions. While at it, also fix one tiny whitespace typo. Signed-off-by: NLuka Perkov <luka@openwrt.org> Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>
-
- 22 11月, 2013 1 次提交
-
-
由 Albert ARIBAUD 提交于
-
- 12 11月, 2013 9 次提交
-
-
由 Samuel Egli 提交于
- dxr2: define unused pins as input - do not enable RTC32K OSC on dxr2 board - update default environment - add splashpos=m,m to default environment, so splash screen is always centered. - adapt environment for bootcount feature - add altbootcmd to default environment - rut: SPL add early reset pulse for eth-phy, maXTouch and display - rut: display timing aenderungen - siemens boards: adapt for background color = white - add boutcount feature for the siemens boards store the bootcount in the environment, as we have no softreset save registers on this hardware. Use therefore the CONFIG_BOOTCOUNT_ENV bootcount driver. - change spi mode from 3 to 0 for the lcd init - add gpio pin for lcd reset with state 0 and add mdelay - siemens boards: use own USB id's - add dfu serial and device number for siemens boards Add for the siemens boards the possibility to define in dfu mode, the iSerialNumber and the bcdDevice fields in the USB Device descriptor. - fix upgrade mechanism based on bootcount Correct location of saveenv and remove not active variable. Add CONFIG_BOOT_RETRY_TIME and CONFIG_RESET_TO_RETRY to reboot board in case of empty kernel partition. Without these defines an empty kernel partition leads to an abort of boot process and one remains in u-boot prompt. - general cleanup of dxr2, pxm2 and rut boards all: * Remove net boot from bootcmd Ping can cause a crash on boards without ethernet phy. net_nfs command is used only for development * Add reset at the end of bootcmd In order to have an immediate reset of the boot when bootcmd fails, add reset at the end of bootcmd. rut: * add nand_img_size dxr2: * update nand_img_size * ddr3 timings updated with iocontrol property that can be modified via eeprom. New default parameters from software leveling with draco ES2. Signed-off-by: NSamuel Egli <samuel.egli@siemens.com> Signed-off-by: NPascal Bach <pascal.bach@siemens.com> Signed-off-by: NRoger Meier <r.meier@siemens.com> Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Matthias Michel <matthias.michel@siemens.com> Cc: Tom Rini <trini@ti.com>
-
由 Heiko Schocher 提交于
add the possibility to set the bcdDevice number board specific. Therefore the weak function g_dnl_get_board_bcd_device_number() is introduced. Used on the siemens boards. Signed-off-by: NHeiko Schocher <hs@denx.de> Acked-by: NLukasz Majewski <l.majewski@samsung.com> Cc: Marek Vasut <marek.vasut@gmail.com> Cc: Kyungmin Park <kyungmin.park@samsung.com>
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@ti.com>
-
由 Tom Rini 提交于
Some am33xx boards may not use the RTC block for bootcount (as it may not be wired up for the board) and use some other facility. So add another symbol for the bootcount driver for the IP block. Acked-by: NHeiko Schocher <hs@denx.de> Signed-off-by: NTom Rini <trini@ti.com>
-
由 Igor Grinberg 提交于
Switch to using the generic gpio_led driver instead of the private to cm_t35 board led implementation. Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Tested-by: NNikita Kiryanov <nikita@compulab.co.il>
-
由 Andrew Bradford 提交于
Commit f6d1f6e4 broke selection of UARTs other than UART0 for am335x_evm configurations by setting CONS_INDEX to 1 for all configurations. Revert the CONS_INDEX changes. Signed-off-by: NAndrew Bradford <andrew@bradfordembedded.com>
-
由 Matt Porter 提交于
Update my email address as ti814x_evm maintainer to save people some frustrating bounces and non-response. Signed-off-by: NMatt Porter <matt.porter@linaro.org>
-
由 Heiko Schocher 提交于
As http://www.denx.de/wiki/view/U-Boot/DesignPrinciples#2_Keep_it_Fast states: "Initialize devices only when they are needed within U-Boot" enable the RTC32K OSC only, if CONFIG_SPL_AM33XX_ENABLE_RTC32K_OSC is enabled. Enable this in ti_am335x_common.h, so all boards in mainline should work as before. Signed-off-by: NHeiko Schocher <hs@denx.de> Cc: Tom Rini <trini@ti.com>
-
由 Heiko Schocher 提交于
If no softreset save registers are found on the hardware "bootcount" is stored in the environment. To prevent a saveenv on all reboots, the environment variable "upgrade_available" is introduced. If "upgrade_available" is 0, "bootcount" is always 0 therefore no need to save the environment on u-boot boot, if "upgrade_available" is 1 "bootcount" is incremented in the environment and environment gets written on u-boot start. So the Userspace Applikation must set the "upgrade_available" and "bootcount" variable to 0 (for example with fw_setenv), if a boot was successfully. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
- 10 11月, 2013 1 次提交
-
-
由 Albert ARIBAUD 提交于
Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
-
- 09 11月, 2013 13 次提交
-
-
-
由 Rob Herring 提交于
Convert sandbox to use common time functions. Signed-off-by: NRob Herring <rob.herring@calxeda.com>
-
由 Rob Herring 提交于
A weak annotation is needed in order to prevent link errors when get_ticks is overridden. This fixes sandbox build. Signed-off-by: NRob Herring <rob.herring@calxeda.com>
-
由 Suriyan Ramasami 提交于
Netconsole loses the second character when used as input by either setenv stdin nc or setenv stdin serial,nc if using CONSOLE_CONSOLE_MUX Before a nc_send_packet() to echo the input, a check is done to see if nc_ether is valid. If its not, it waits for an arp request and then sends the packet (which contains the first character of line to be displayed as output). As part of reaping the arp request, the second character is consumed. We protect this by making the call to NetLoop(NETCONS) between input_recursion. Signed-off-by: NSuriyan Ramasami <suriyan.r@gmail.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Axel Lin 提交于
Staticize local functions in s5p serial driver. Signed-off-by: NAxel Lin <axel.lin@ingics.com> Acked-by: NMinkyu Kang <mk7.kang@samsung.com>
-
由 Pierre Aubert 提交于
The env export command doesn't export the first variable of the list since commit 5a31ea04 "env grep" - reimplement command using hexport_r() Signed-off-by: NPierre Aubert <p.aubert@staubli.com>
-
由 Mark Langsdorf 提交于
Let highbank users break into the autoboot script with ctrl-c. Signed-off-by: NMark Langsdorf <mark.langsdorf@calxeda.com>
-
由 Mark Langsdorf 提交于
As originally implemented, setting the AUTOBOOT_KEYED config option will prevent users from breaking into the autoboot script with ctrl-c. Restore that option with a new config symbol. Signed-off-by: NMark Langsdorf <mark.langsdorf@calxeda.com>
-
由 Axel Lin 提交于
Staticize local functions in xuartlite driver. Signed-off-by: NAxel Lin <axel.lin@ingics.com> Acked-by: NStefan Roese <sr@denx.de> Tested-by: NMichal Simek <monstr@monstr.eu>
-
由 Axel Lin 提交于
Staticize local functions in mxs_auart driver. Signed-off-by: NAxel Lin <axel.lin@ingics.com> Acked-by: NMarek Vasut <marex@denx.de>
-
由 Piotr Wilczek 提交于
Curently memcpy copies string without null terminating char because function strlen returns only number of characters excluding null terminating character. Replace memcpy with strcpy. Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> CC: Tom Rini <trini@ti.com>
-
由 Luka Perkov 提交于
Signed-off-by: NLuka Perkov <luka@openwrt.org>
-
由 Luka Perkov 提交于
Signed-off-by: NLuka Perkov <luka@openwrt.org>
-