Skip to content

U
U-Boot.Mirror

OS / U-Boot.Mirror

通知 1
Star 0
Fork 0
U
U-Boot.Mirror

前往新版Gitcode，体验更适合开发者的 AI 搜索 >>

切换分支/标签
  1. 29 4月, 2020 1 次提交
  3. 23 1月, 2020 1 次提交
  5. 05 12月, 2019 2 次提交
  7. 04 12月, 2019 1 次提交
  9. 21 11月, 2019 2 次提交
    • T
      env: Finish migration of common ENV options · a09fea1d
      由 Tom Rini 提交于 
      - In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
      a09fea1d
    • T
      env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol · 8d8ee47e
      由 Tom Rini 提交于 
      Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
      8d8ee47e
  11. 08 11月, 2019 1 次提交
  13. 30 4月, 2019 1 次提交
  15. 20 10月, 2018 1 次提交
  17. 04 9月, 2018 1 次提交
  19. 17 8月, 2018 1 次提交
    • T
      configs: Migrate CONFIG_NR_DRAM_BANKS · 86cf1c82
      由 Tom Rini 提交于 
      We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.
Signed-off-by: NTom Rini <trini@konsulko.com>
      86cf1c82
  21. 28 4月, 2018 1 次提交
    • A
      Convert CONFIG_SPI to Kconfig · f1b1f770
      由 Adam Ford 提交于 
      This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
      f1b1f770
  23. 30 3月, 2018 2 次提交
  25. 24 2月, 2018 1 次提交
  27. 15 2月, 2018 2 次提交
  29. 11 2月, 2018 2 次提交
  31. 27 12月, 2017 1 次提交
  33. 30 11月, 2017 3 次提交
  35. 11 10月, 2017 1 次提交
    • T
      cmd: Toggle the default value of CONFIG_CMD_IMLS · ad12dc18
      由 Tuomas Tynkkynen 提交于 
      Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
   i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
      ad12dc18
  37. 21 9月, 2017 1 次提交
  39. 26 7月, 2017 1 次提交
  41. 19 6月, 2017 1 次提交
  43. 23 5月, 2017 1 次提交
    • R
      nds32: eth: Support ftmac100 DM. · be71a179
      由 rick 提交于 
      Support Andestech eth ftmac100 device tree flow on AG101P/AE3XX platform.
Verification:
 Boot linux kernel via dhcp and bootm ok.

 NDS32 # setenv bootm_size 0x2000000;setenv fdt_high 0x1f00000;
 NDS32 # dhcp 0x600000 10.0.4.97:boomimage-310y-ae300-spi.bin
 BOOTP broadcast 1
 BOOTP broadcast 2
 BOOTP broadcast 3
 BOOTP broadcast 4
 DHCP client bound to address 10.0.4.178 (4899 ms)
	Using mac@e0100000 device
	TFTP from server 10.0.4.97; our IP address is 10.0.4.178
	Filename 'boomimage-310y-ae300-spi.bin'.
	Load address: 0x600000
	Loading: #################################################################
	         #################################################################
	         #################################################################
...
...
	         ###################################
	         233.4 KiB/s
					 done
					 Bytes transferred = 13872076 (d3abcc hex)
	NDS32 # dhcp 0x2000000 10.0.4.97:ae300.dtb
	BOOTP broadcast 1
	BOOTP broadcast 2
	BOOTP broadcast 3
	BOOTP broadcast 4
	DHCP client bound to address 10.0.4.178 (4592 ms)
	Using mac@e0100000 device
	TFTP from server 10.0.4.97; our IP address is 10.0.4.178
	Filename 'ae300.dtb'.
	Load address: 0x2000000
	Loading: #
	         82 KiB/s
					 done
					 Bytes transferred = 2378 (94a hex)
	NDS32 # bootm 0x600000 - 0x2000000
	 Image Name:
	 Created:      2017-03-22   6:52:03 UTC
	 Image Type:   NDS32 Linux Kernel Image (uncompressed)
	 Data Size:    13872012 Bytes = 13.2 MiB
	 Load Address: 0000c000
	 Entry Point:  0000c000
	 Verifying Checksum ... OK
	 Booting using the fdt blob at 0x2000000
	 Loading Kernel Image ... OK
	 Loading Device Tree to 01efc000, end 01eff949 ... OK
	 Linux version 3.10.102-20375-gb0034c1-dirty (rick@app09)
	(gcc version 4.9.3 (2016-07-06_nds32le-linux-glibc-v3_experimental) )
  #293 PREEMPT Wed Mar 22 14:49:28 CST 2017
	CPU: NDS32 N13, AndesCore ID(wb), CPU_VER 0x0d11103f(id 13, rev 17, cfg 4159)
...
...
Signed-off-by: Nrick <rick@andestech.com>
      be71a179
  45. 22 5月, 2017 3 次提交
  47. 01 5月, 2017 1 次提交
  49. 20 3月, 2017 1 次提交
  51. 14 3月, 2017 1 次提交
  53. 13 2月, 2017 1 次提交
    • M
      flash: complete CONFIG_SYS_NO_FLASH move with renaming · e856bdcf
      由 Masahiro Yamada 提交于 
      We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH".  Flipping the logic will
make the code more readable.  Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
    common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
  find . -path './configs/*_defconfig' | xargs sed -i \
  -e '/CONFIG_SYS_NO_FLASH=y/d' \
  -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
  find . -name '*.[ch]' | xargs sed -i \
  -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
  -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
  -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
  -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
  - Rename the rest of instances
  - Remove the description from README
  - Create the new Kconfig entry in drivers/mtd/Kconfig
  - Remove the old Kconfig entry from common/Kconfig
  - Remove the garbage comments from include/configs/*.h
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
      e856bdcf
  55. 30 12月, 2016 1 次提交
    • M
      mmc: complete unfinished move of CONFIG_MMC · c2726995
      由 Masahiro Yamada 提交于 
      Commit 7a777f6d ("mmc: Add generic Kconfig option") created
a Kconfig entry for this option without any actual moves, then
commit 44c79879 ("sunxi: Use Kconfig CONFIG_MMC") moved
instances only for SUNXI.

We generally do not like such partial moves.  This kind of work
is automated by tools/moveconfig.py, so it is pretty easy to
complete this move.

I am adding "default ARM || PPC || SANDBOX" (suggested by Tom).
This shortens the configs and will ease new board porting.

This commit was created as follows:

[1] Edit Kconfig (remove the "depends on", add the "default",
    copy the prompt and help message from Linux)

[2] Run 'tools/moveconfig.py -y -s -r HEAD MMC'
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NJaehoon Chung <jh80.chung@samsung.com>
      c2726995
  57. 10 6月, 2016 1 次提交
  59. 26 4月, 2016 2 次提交