- 29 4月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 29 2月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 23 1月, 2020 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 05 12月, 2019 3 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Miquel Raynal 提交于
MTD support must be enabled when using mtdparts. Indeed, functions like get_mtd_info(), get_mtd_device() and put_mtd_device() are in drivers/mtd/mtd_uboot.c and are built only with CONFIG_MTD. Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: NBoris Brezillon <boris.brezillon@bootlin.com>
-
由 Miquel Raynal 提交于
Both symbols must be enabled when there is a raw NAND driver selected. Also enable them when CONFIG_CMD_NAND is selected to avoid breaking things when we'll further rework the MTD dependency description. Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com> Reviewed-by: NBoris Brezillon <boris.brezillon@bootlin.com> [trini: Rebase and migrate a few more boards here] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 04 12月, 2019 1 次提交
-
-
由 Miquel Raynal 提交于
Add more clarity by changing the Kconfig entry name. Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com> [trini: Re-run migration, update a few more cases] Signed-off-by: NTom Rini <trini@konsulko.com> Reviewed-by: NBoris Brezillon <boris.brezillon@bootlin.com>
-
- 21 11月, 2019 2 次提交
-
-
由 Tom Rini 提交于
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
-
由 Tom Rini 提交于
Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 13 11月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Move this symbol to Kconfig. As part of this we can drop a UBI-specific symbol that was a stop-gap for not having this particular symbol in Kconfig. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 23 9月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 27 5月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 21 5月, 2019 9 次提交
-
-
由 Mario Six 提交于
Migrate the CONFIG_LCRR_* settings to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Migrate the arbiter configuration to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Mirate the HID configuration settings to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Migrate the BR/OR settings to Kconfig. These must be known at compile time, so cannot be configured via DT. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
The LBLAW_* values determine the window configuration of the memory controller. Hence, they must be known at compile time, and cannot be implemented in the DT mechanism. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
The BATs (block address translation registers) determine the initial memory window mappings. Hence, they must be known at compile time and cannot be implemented in the DT mechanism. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Migrate the CONFIG_HIGH_BATS variable to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
The HRCW (hardware reset configuration word) is a constant that must be hard-coded into the boot loader image. So, it must be available at compile time, and cannot be migrated to the DT mechanism, but has to be kept in Kconfig. Configuration of this crucial variable should still be somewhat comfortable. Hence, make its fields configurable in Kconfig, and assemble the final value from these. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
MPC83xx uses CONFIG_83XX_CLKIN instead of CONFIG_SYS_CLK_FREQ to set the system clock. To migrate the architecture, we can replace CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ. To do this * replace all occurrences of CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ * set CONFIG_SYS_CLK_FREQ to the old value of CONFIG_83XX_CLKIN in all MPC83xx config files Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
- 20 5月, 2019 1 次提交
-
-
由 Mario Six 提交于
MPC8313ERDB has the option of either enabling NOR or NAND boot in its config file (by commenting out certain #ifdefs). To keep this ability after migrating options to Kconfig, we introduce two MPC8313ERDB configs: one for NOR, and one for NAND. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
- 30 4月, 2019 1 次提交
-
-
由 Simon Goldschmidt 提交于
Moved CONFIG_SPL_TEXT_BASE to common/spl/Kconfig and migrate existing values. Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com> [trini: Re-run migration] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 20 10月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_FLASH_CFI_DRIVER CONFIG_SYS_FLASH_USE_BUFFER_WRITE CONFIG_FLASH_CFI_MTD CONFIG_SYS_FLASH_PROTECTION CONFIG_SYS_FLASH_CFI Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Re-migrate] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 18 8月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 04 6月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 15 5月, 2018 1 次提交
-
-
由 Mario Six 提交于
The CONFIG_PHY_MARVELL has already been migrated to Kconfig (some boards already had it in their Kconfig), but had not been moved for older boards. Move it to the defconfigs for all boards. Signed-off-by: NMario Six <mario.six@gdsys.cc> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 17 4月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 4月, 2018 2 次提交
-
-
由 Mario Six 提交于
Migrate the CONFIG_TSEC_ENET option to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
由 Mario Six 提交于
Migrate the CONFIG_BOARD_EARLY_INIT_R option to Kconfig. Signed-off-by: NMario Six <mario.six@gdsys.cc>
-
- 08 4月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 24 2月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Re-run the migration] Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 15 2月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the current set of options we have in Kconfig. We will need to have some options available for SPL and !SPL_FRAMEWORK so this is important. In a few cases we re-order existing options so that we have less escapes from the SPL_FRAMEWORK guard. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 11 2月, 2018 1 次提交
-
-
由 Tom Rini 提交于
On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 27 1月, 2018 1 次提交
-
-
由 Maxime Ripard 提交于
Now that we have everything in place in the code, let's allow to build multiple environments backend through Kconfig. Reviewed-by: NAndre Przywara <andre.przywara@arm.com> Reviewed-by: NLukasz Majewski <lukma@denx.de> Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
- 06 11月, 2017 1 次提交
-
-
由 Tom Rini 提交于
We move all instances of CONFIG_MTDIDS_DEFAULT and CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files. There's a few cases here where we need to expand upon what was in the header file. Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 11 10月, 2017 1 次提交
-
-
由 Tuomas Tynkkynen 提交于
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
-
- 28 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 15 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 12 8月, 2017 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_NAND Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Sync up a few more, add imply's] Signed-off-by: NTom Rini <trini@konsulko.com>
-