- 04 6月, 2015 21 次提交
-
-
由 Bin Meng 提交于
The default weak version of pci_skip_dev() in drivers/pci/pci_common.c skips the host bridge (b.d.f = 0.0.0) which is actually the i440fx/q35 chipset for QEMU targets. Define CONFIG_PCI_CONFIG_HOST_BRIDGE to make it visible in the PCI configuration space. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Andrew Bradford 提交于
High mem starts at 4 GiB. Signed-off-by: NAndrew Bradford <andrew.bradford@kodakalaris.com> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
If pirq_routing_table points to NULL, that means U-Boot fails to generate the table before in create_pirq_routing_table(), so we test it against NULL before actually writing it. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
Intel Quark SoC has the same interrupt routing mechanism as the Queensbay platform, only the difference is that PCI devices' INTA/B/C/D are harcoded and cannot be changed freely. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
Describe all required properties needed by the irq router device tree. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
PIRQ routing is pretty much common in Intel chipset. It has several PIRQ links (normally 8) and corresponding registers (either in PCI configuration space or memory-mapped IBASE) to configure the legacy 8259 IRQ vector mapping. Refactor current Queensbay PIRQ routing support using device tree and move it to a common place, so that we can easily add PIRQ routing support on a new platform. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
Enable legacy IDE support on the pc target and AHCI support on the q35 target. Default configuration is to support the pc target. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
Enable CONFIG_LBA48 to support large disks. CONFIG_ATAPI is only needed by cmd_ide.c which is not common for modern x86 targets, hence remove it. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
Eliminate the following build warning in atapi_inquiry(): "warning: assignment from incompatible pointer type [enabled by default]" Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
The legacy IDE device has a BAR4 (Bus Master Interface BAR) which needs to be configured. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
Remove the '#undef DEBUG' in pci_auto.c so that we can enable debug message output via '-DDEBUG'. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
It turns out that QEMU x86 emulated graphic card has a built-in option ROM which can be run perfectly with native mode by U-Boot. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
CONFIG_FRAMEBUFFER_SET_VESA_MODE and CONFIG_FRAMEBUFFER_VESA_MODE are not x86-specific, so move them to drivers/video/Kconfig and make them depend on VIDEO_VESA driver. Some cosmetic fixes are applied to the Kconfig help text as well. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
There is no reason to prevent CONFIG_VIDEO_VESA driver working on non-x86 boards, so remove such limitation. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
gd is not referenced in those board files so DECLARE_GLOBAL_DATA_PTR should be removed. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
Document how to build and test U-Boot with QEMU. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
QEMU is much easier for us test booting U-Boot as a coreboot payload than having a real board like chromebook_link. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org> Tested-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
Some x86 boards set CONFIG_NR_DRAM_BANKS to 1, which causes incorrect DRAM size printed when booting from coreboot, like this: CPU: x86, vendor Intel, device 663h DRAM: 636 KiB Using default environment Change it to 8 which should be enough for both coreboot and bare cases, and move it to x86-common.h. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
Now that we have QEMU support, make it the default vendor in the 'make menuconfig' screen. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org> Tested-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
This commit introduces the initial U-Boot support for QEMU x86 targets. U-Boot can boot from coreboot as a payload, or directly without coreboot. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org> Tested-by: NSimon Glass <sjg@chromium.org> Merged in patch 'x86: qemu: Add CMD_NET to qemu-x86_defconfig https://patchwork.ozlabs.org/patch/479745/
-
由 Bin Meng 提交于
pci_hose_phys_to_bus() is needed by several drivers. Move it to pci_common.c to avoid a broken build when CONFIG_DM_PCI is on. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Acked-by: NSimon Glass <sjg@chromium.org>
-
- 03 6月, 2015 1 次提交
-
-
由 Hannes Schmelzer 提交于
netconsole had become defective over time and cleanups. Because the feature is used very rarely nobody did take notice about this defect. With this patch the resulting syntax error on call will be fixed. Signed-off-by: NHannes Schmelzer <oe5hpm@oevsv.at>
-
- 02 6月, 2015 4 次提交
-
-
由 Lars Poeschel 提交于
CONFIG_NET_MULTI is not used anywhere and thus can safely be removed from the configs. Acked-by: NMarek Vasut <marex@denx.de> Acked-by: NViresh Kumar <viresh.kumar@linaro.org> Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
-
由 Lars Poeschel 提交于
The config for pcm051 still undef'd CONFIG_USE_IRQ. This is not needed any more since it is not defined in the whole include path before. Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
-
git://git.denx.de/u-boot-net由 Tom Rini 提交于
Fixup include/configs/unipher.h to not set CONFIG_LIB_RAND Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Michal Simek 提交于
NET_RANDOM_ETHADDR depends on lib/rand.c. This patch adds dependency to Kconfig to ensure that library is also compiled. Remove the definitions from Blackfin boards' include/configs. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 01 6月, 2015 10 次提交
-
-
由 Joe Hershberger 提交于
This also selects CONFIG_NET for any CONFIG_CMD_NET board. Remove the imx default for CONFIG_NET. This moves the config that was defined by 60296a83 (commands: add more command entries in Kconfig). Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Another shell scripting command that has not been moved. Moved using tools/moveconfig.py using these settings: CMD_SETEXPR bool n y Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com> Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
Commit 76ec988b (net: Remove all calls to net_random_ethaddr()) accidentally deleted CONFIG_TARGET_BCT_BRETTL2=y, and since then bct-brettl2 would not build. Since commit a26cd049 (arch: Make board selection choices optional), Kconfig actually allows such a .config file in which no board is selected, but the build never succeeds. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Masahiro Yamada 提交于
Commit 92ac5208 (net: Remove all references to CONFIG_ETHADDR and friends) accidentally dropped #endif. Since then, gr_ep2s60 could not build. scripts/kconfig/conf --silentoldconfig Kconfig CHK include/config.h GEN include/autoconf.mk In file included from include/config.h:5:0, from ./include/common.h:18: include/configs/gr_ep2s60.h:15:0: error: unterminated #ifndef #ifndef __CONFIG_H__ ^ make[1]: *** [include/autoconf.mk] Error 1 Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
-
由 Nobuhiro Iwamatsu 提交于
This updates r8a7794 QoS to revision 0.31 for ES1 and revision 0.321 for ES2. Signed-off-by: NKouei Abe <kouei.abe.cp@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This updates r8a7793 QoS to revision 0.311. Signed-off-by: NKouei Abe <kouei.abe.cp@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This updates r8a7791 QoS to revision 0.411. Signed-off-by: NKouei Abe <kouei.abe.cp@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
This updates r8a7790 QoS to revision 0.973. This commit can changed from KConfig to fit contents of the QoS. Signed-off-by: NKouei Abe <kouei.abe.cp@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Mitsuhiro Kimura 提交于
Ethernet function of Alt board can select normal and B by DIP switch on board. But user need to set not only DIP switch but also pin function. This adds pin function of Ethernet function B. This can select from Kconfig. Signed-off-by: NMitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
- 31 5月, 2015 4 次提交
-
-
-
-
由 Masahiro Yamada 提交于
The chip select 1 of the NAND controller is available if you want to use, although the pins are shared with UART port 2. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-
由 Masahiro Yamada 提交于
The register value should be 1, not 4. Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
-