- 01 6月, 2007 4 次提交
-
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
This patch adds hardware ECC support to the NDFC driver. It also changes the register access from using the "simple" in32/out32 functions to the in_be32/out_be32 functions, which make sure that the access is correctly synced. This is the only recommended access to SoC registers in the current Linux kernel. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
This patch updates the nand_ecc code to the latest Linux version. The main reason for this is the more compact code. This makes it possible to include the ECC code into the NAND bootloader image (NAND_SPL) for PPC4xx. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
- 29 4月, 2007 2 次提交
-
-
由 Stefan Roese 提交于
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
- 24 4月, 2007 1 次提交
-
-
由 Matthias Fuchs 提交于
Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>
-
- 19 4月, 2007 1 次提交
-
-
由 Stefan Roese 提交于
Previous versions used full wait states for the chip select #1 which is connected to the Xilinix SystemACE controller on the AMCC Katmai evaluation board. This leads to really slow access and therefore low performance. This patch now sets up the chip select a lot faster resulting in much better read/write performance of the Linux driver. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 18 4月, 2007 4 次提交
-
-
-
由 Domen Puncer 提交于
Signed-off-by: NDomen Puncer <domen.puncer@telargo.com>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Now 405EZ ports also show upon bootup from which boot device they are configured to boot: U-Boot 1.2.0-gd3832e8f-dirty (Apr 18 2007 - 07:47:05) CPU: AMCC PowerPC 405EZ Rev. A at 199.999 MHz (PLB=133, OPB=66, EBC=66 MHz) Bootstrap Option E - Boot ROM Location EBC (32 bits) 16 kB I-Cache 16 kB D-Cache Board: Acadia - AMCC PPC405EZ Evaluation Board Signed-off-by: NStefan Roese <sr@denx.de>
-
- 16 4月, 2007 1 次提交
-
-
由 Domen Puncer 提交于
U-Boot part of Lite5200b low power mode support. Puts SDRAM out of self-refresh and transfers control to address saved at physical 0x0. Signed-off-by: NDomen Puncer <domen.puncer@telargo.com> Acked-by: NGrant Likely <grant.likely@secretlab.ca>
-
- 15 4月, 2007 1 次提交
-
-
由 Wolfgang Denk 提交于
-
- 14 4月, 2007 1 次提交
-
-
由 Heiko Schocher 提交于
clear the Display after reset. Signed-off-by: NHeiko Schocher <hs@denx.de>
-
- 13 4月, 2007 2 次提交
-
-
由 Denis Peter 提交于
Fix bug introduced by "Fix get_partition_info() parameter error in all other calls" from 2005-03-04 in cmd_ide.c and cmd_scsi.c, which prevented to use diskboot or scsiboot form another device than 0. Signed-off-by: NDenis Peter <d.peter@mpl.ch>
-
由 Greg Lopp 提交于
Signed-of-by: NGreg Lopp <lopp@pobox.com> Acked-by: NGrant Likely <grant.likely@secretlab.ca>
-
- 12 4月, 2007 2 次提交
-
-
由 Jeffrey Mann 提交于
This patch fixes changes the i2c_init(...) function to use the function get_OPB_freq() rather than calculating the OPB speed by sysInfo.freqPLB/sysInfo.pllOpbDiv. The get_OPB_freq() function is specific per processor. The prior method was not and so was calculating the wrong speed for some PPC4xx processors. Signed-off-by: NJeffrey Mann <mannj@embeddedplanet.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
-
- 11 4月, 2007 2 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
* Make IDE timeout configurable through ide_reset_timeout variable. * Use Newline as "password" string * Use just a single partition in NAND flash
-
- 04 4月, 2007 4 次提交
-
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
由 Wolfgang Denk 提交于
-
- 02 4月, 2007 1 次提交
-
-
由 Stefan Roese 提交于
With this new base address of the Xilinx SystemACE controller the Linux driver will be easier to adapt, since it can now be mapped via the "normal" ioremap() call. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 01 4月, 2007 6 次提交
-
-
由 Gerald Van Baren 提交于
-
由 Gerald Van Baren 提交于
Modifications to the existing code to support the new fdt command.
-
由 Gerald Van Baren 提交于
The fdt command uses David Gibson's libfdt library to manipulate as well as print the flattened device tree. This patch is the new command, the second part is the modifications to the existing code.
-
由 Gerald Van Baren 提交于
Enhanced the formerly private function _fdt_next_tag() to allow stepping through the tree, used to produce a human-readable dump, and made it part of the published interface. Also added some comments.
-
由 Gerald Van Baren 提交于
Changes to David Gibson's original source to fit into u-boot's environment. No functionality changes.
-
由 Gerald Van Baren 提交于
This adds the applicable libfdt source files (unmodified) and a README to explain where the source came from.
-
- 31 3月, 2007 8 次提交
-
-
由 Gerald Van Baren 提交于
This adds the applicable libfdt source files (unmodified) and a README to explain where the source came from.
-
-
由 Stefan Roese 提交于
Now the DDR2 frequency is also 2*PLB frequency when 166MHz PLB is selected. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Additional RAM information is now printed upon powerup, like DDR2 frequency and CAS latency. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
With the updated 44x DDR2 driver the Yucca board now supports ECC generation and checking. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
The board specific "bootstrap" command is now fixed and can be used for the AMCC Katmai board to configure different CPU/PLB/OPB frequencies. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Fix a bug in the auto calibration routine. This driver now runs more reliable with the tested modules. It's also tested with 167MHz PLB frequency (667MHz DDR2 frequency) on the Katmai. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Michal Simek 提交于
-