Previously, dtoc could only process the top-level nodes which led to
device nodes in hierarchical trees to be ignored. E.g. the mmc0 node
in the following example would be ignored, as only the soc node was
processed:

  / {
	soc {
		mmc0 {
			/* ... */
		};
	};
  };

This introduces a recursive helper method ScanNode, which is used by
ScanTree to recursively parse the entire tree hierarchy.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

We used to get the address of the optionnal ctrl_mod_mmap register as the
third memory range of the "reg" property. the linux driver moved to use a
syscon instead. In order to keep the DTS as close as possible to that of
linux, we move to using a syscon as well.

If SYSCON is not supported, the driver reverts to the old way of getting
the address from the 3rd memory range
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

In the DTS, the addresses are defined relative to the parent bus. We need
to translate them to get the address as seen by the CPU core.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

commit 2f11cd91 ("dm: core: Handle global_data moving in SPL")
handles relocation of GD in SPL if spl_init() is called before
board_init_r(). So, uclass_root.next need not be initialized always
and accessing uclass_root.next->prev gives an abort. Update the
uclass_root only if it is available.
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

The Xenon SDHCI driver just missed the integration of this patch:

git ID 6d0e34bf
mmc: sdhci: Distinguish between base clock and maximum peripheral frequency

With this patch applied, the SDHCI subsystem complains now with this warning
while probing:

sdhci_setup_cfg: Hardware doesn't specify base clock frequency

This patch fixes this issue, by providing the missing host->max_clk
variable to the SDHCI subsystem.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Hu Ziji <huziji@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>

It's redundant to send cmd13 after cmd9 whose response is not R1b. The
card devices will not be busy w/ cmd9.
Signed-off-by: NZiyuan Xu <xzy.xu@rock-chips.com>

No need to flush cache for command without data.
Signed-off-by: NKevin Liu <kevinliu@asrmicro.com>

This patch adds Intel Tangier eMMC/SDHCI driver.

Intel Tangier SoC contains a hybrid of PCI and non-PCI devices. SDHCI
controller is one of the devices which are *not* on a PCI and, hence,
cannot be enumerated by standard PCI means. This driver, allows for
SDHCI controller on Tangier SoC to work in U-Boot.
Signed-off-by: NVincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

We don't want pci_mmc to compile every time x86 compiles, only when
there's a platform that needs it. For that reason, we're adding a new
CONFIG_MMC_PCI which platforms can choose to enable.
Suggested-by: NJaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>

Enable SPL_DM on all AM43xx based platforms
Reviewed-by: NTom Rini <trini@konsulko.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Enable DM_I2C/SPI/ETH for all AM43XX based boards.
Enable it using imply keyword so that a user can
disable this when not needed.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Add u-boot specific dtsi for am43xx-gp-evm so
that it will be used for SPL.
Reviewed-by: NTom Rini <trini@konsulko.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Enable SPL_DM on all DRA7 based platforms.
Reviewed-by: NTom Rini <trini@konsulko.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Enable SPL_DM on all AM57xx based platforms.
Reviewed-by: NTom Rini <trini@konsulko.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Add u-boot specific dtsi so that this will be
included automatically while building dts.
Reviewed-by: NTom Rini <trini@konsulko.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

To make SPL_OF_CONTROL work on OMAP2+ SoCs, _image_binary_end must be
defined in the linker script along with CONFIG_SPL_SEPARATE_BSS.
Reviewed-by: NTom Rini <trini@konsulko.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>

Calls to IS_ENABLED() on a non-y/n option will always be false, even
when set.  We can correct this by adding a new bool value that is set
based on the conditions required for SPL_STACK_R_MALLOC_SIMPLE_LEN to be
set instead.

Fixes: 340f418a ("spl: Add spl_early_init()")
Reported-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
---
Changes in v2:
- Fix thinko pointed out by Lokesh

Add support for the Broadcom Northstar2 SoC and SVK (bcm958712k).  The
BCM5871X is a series of quad-core 64-bit 2GHz ARMv8 Cortex-A57
processors targeting a broad range of networking applications.
Signed-off-by: NJon Mason <jon.mason@broadcom.com>

Add instructions to write an AIS image to NAND
by using the u-boot nand tools.
Signed-off-by: NAxel Haslam <ahaslam@baylibre.com>

When building u-boot tools in cross-build environment CFLAGS environment
variable set up for target is taken into an account when building code
for host. Make it empty on invocation of python.

This fixes the following build errors when cross-compiling for xtensa:

  cc1: error: unrecognized command line option "-mlongcalls"
  cc1: error: unrecognized command line option "-mauto-litpools"
Signed-off-by: NMax Filippov <jcmvbkbc@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NTom Rini <trini@konsulko.com>

The CAAM in IMX parts doesn't support public key hardware acceleration
(PKHA), so don't use RSA_FREESCALE_EXP. If you try to use it on IMX
(assuming you have the clocks enabled first) you will get back an
"Invalid KEY Command" error since PKHA isn't a valid key destination for
these parts.
Signed-off-by: NGeorge McCollister <george.mccollister@gmail.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Currently, AM43xx just re-uses the version strings from AM33xx which is
wrong; the actual values for AM43xx are different. Fix this by adding
a separate version string array for AM43xx and use this instead.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Reported-by: NSekhar Nori <nsekhar@ti.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>
Reviewed-by: NTom Rini <trini@konsulko.com>

* Add note that execution needs Python development package installed
* Standardize on upper case "FIT", "FDT" as necessary for clarity
* Fix "tempoerary", "linex" typos
Signed-off-by: NRobert P. J. Day <rpjday@crashcourse.ca>

This adds documentation on the u-boot,efi-partition-entries-offset
property (which overrides CONFIG_EFI_PARTITION_ENTRIES_OFF, if
present).
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This moves the description of the /config node from README.fdt-control
into a separate file doc/device-tree-bindings/config.txt.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Some architectures require their SPL loader at a fixed address within
the first 16KB of the disk. To avoid an overlap with the partition
entries of the EFI partition table, the first safe offset (in bytes,
from the start of the device) for the entries can be set through
CONFIG_EFI_PARTITION_ENTRIES_OFF (via Kconfig)

When formatting a device with an EFI partition table, we may need to
leave a gap between the GPT header (always in LBA 1) and the partition
entries. The GPT header already contains a field to specify the
on-disk location, which has so far always been set to LBA 2. With this
change, a configurable offset will be translated into a LBA address
indicating where to put the entries.

Now also allows an override via device-tree using a config-node (see
doc/device-tree-bindings/config.txt for documentation).

Tested (exporting an internal MMC formatted with this) against Linux,
MacOS X and Windows.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
[trini: __maybe_unused on config_offset to avoid warning]
Signed-off-by: NTom Rini <trini@konsulko.com>

If the ethernet address environment is set with a valid
ethernet address prevent overriding it as it is most likely
set by the user and he/she doesn't want board code to
automatically override it whatsoever.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

PRU ethernet MAC address range is present in the
board EEPROM. Parse it and setup eth?addr
environment variables.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

In stead of defining the board EEPROM address in the board headers
let's define them in the board config files and make them
configurable by Kconfig.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

AM571x IDK and AM572x IDK have optional LCD Kits that can be purchased.
These can be one of OSD101T2045 or the newer OSD101T2587. The LCD panel
itself has no registers that can be used to identify the panel, however,
the touchscreen controllers on the panels are different.

Hence to ease user experience, we can use the touch screen controller's
ID information to detect what kind of panel we use and select the
appropriate kernel dtb for the platform configuration.

NOTE: AM572x IDK default configuration is for LCD Connectivity, however
the AM571x IDK has a jumper (J51) that needs to be mounted for the IDK
to operate with LCD (Vs two PRUSS ethernet port option).

Touchscreen ID information is documented in:
http://www.osddisplays.com/TI/OSD101T2587-53TS_A.1.pdfAcked-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Use the same convention that was used for ICSS1 Ethernet
- If pin is output, set as PIN_OUTPUT
- If pin is input and external pull resistor present set as PIN_INPUT
- If pin is input and external pull resistor absent, set pull to same
as that of the external PHY's internall pull.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>

The board can support either ICSS1 Ethernet ports or LCD
based on J51 jumper. Factory default is ICSS1 Ethernet ports
(i.e. Jumper not populated).

Use the GPIO to detect the jumper setting and configure the
pinmux accordingly. Also select the right DT blob based on
the chosen configuration.

J51 absent -> ICSS1 Ethernet, no LCD on VOUT -> am571x-idk.dtb
J51 present -> LCD on VOUT, no ICSS1 Ethernet -> am571x-idk-lcd-osd.dtb

At present we only support the assume it is the Legacy LCD.
LCD detection mechanism needs to be added later to differentiate
between legacy vs new LCD.

For ICSS1 Ethernet pins use the following convention to set the pinmux
as PMT data is not yet finalized.

- If pin is output, set as PIN_OUTPUT
- If pin is input and external pull resistor present set as PIN_INPUT
- If pin is input and external pull resistor absent, set pull to same
as that of the external PHY's internall pull.
- Do not use SLEW_CONTROLon any pin.

Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>

Keystone and OMAP platforms will need this to set ethernet
MAC addresses from board EEPROM.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Scratch space can be used for features such as board detection. Define
an area within SRAM that can be used for this purpose.

[rogerq@ti.com] Rename EEPROM macro
Signed-off-by: NFranklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>

Non OMAP platforms i.e. Keystone will also need to use the board
EEPROM helpers so let's make the macro platform independent.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

GPIO_TO_PIN(bank, bank_gpio) returns the GPIO index
from the GPIO bank number and bank's GPIO offset number.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>

- The catch-all i.MX6 job has been exceeding the time limit again so
  split this up further.  We now have an i.MX6 job and an
  everything-else job.
- The logic we use to say "Freescale and AArch64" can be more clearly
  expressed with '&' rather than excluding various other things, so
  clear that up.
Signed-off-by: NTom Rini <trini@konsulko.com>

To keep a consistent MMC device mapping in SPL and in u-boot, let's
register the MMC controllers the same way in u-boot and in the SPL.
In terms of boot time, it doesn't hurt to register more controllers than
needed because the MMC device is initialized only prior being accessed for
the first time.
Having the same device mapping in SPL and u-boot allows us to use the
environment in SPL whatever the MMC boot device.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

Signed-off-by: NTom Rini <trini@konsulko.com>

Conflicts:
	configs/bk4r1_defconfig
	configs/colibri_vf_defconfig
	configs/pcm052_defconfig
	include/configs/colibri_vf.h
	include/configs/pcm052.h

Move this in to Kconfig with a default of 115200.
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
[trini: Run moveconfig.py, reword commit slightly]
Signed-off-by: NTom Rini <trini@konsulko.com>