- 07 2月, 2019 1 次提交
-
-
由 Vignesh R 提交于
Now that new SPI NOR layer uses stateless 4 byte opcodes by default, don't enable SPI_FLASH_BAR. For SPI controllers that cannot support 4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c, renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to not break functionality. Signed-off-by: NVignesh R <vigneshr@ti.com> Tested-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com> Tested-by: NStefan Roese <sr@denx.de> Tested-by: NHoratiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: NJagan Teki <jagan@openedev.com> Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed
-
- 08 1月, 2019 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 10 12月, 2018 2 次提交
-
-
由 Jean-Jacques Hiblot 提交于
The DRA7 platforms requires that the dtb used in the SPL really matches the platform to have the best MMC performances. To detect the board type/version an I2C EEPROM is read. This requires that DM is initialized before the detection. As a consequence we must reset the DM after the board detection is a new dtb would better match the platform. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
由 Jean-Jacques Hiblot 提交于
This is required to take advantage of MULTI_DTB_FIT before relocation. If it is too low, DM will be initialized only after relocation has taken place. That is too late for the DRA7 because I2C DM is used before the relocation to setup the voltages required, among other things, to properly initialize the DRAM. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com> Reviewed-by: NHeiko Schocher <hs@denx.de>
-
- 07 12月, 2018 1 次提交
-
-
由 Jean-Jacques Hiblot 提交于
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
- 14 11月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 04 9月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 18 8月, 2018 2 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: NAdam Ford <aford173@gmail.com> [trini: Update the defaults logic slightly] Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: NAdam Ford <aford173@gmail.com> Acked-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 17 8月, 2018 1 次提交
-
-
由 Tom Rini 提交于
We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 04 6月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 30 5月, 2018 2 次提交
-
-
由 Alex Kiernan 提交于
Convert USB fastboot code to use shared fastboot protocol. Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Alex Kiernan 提交于
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to drivers/fastboot. Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing behaviour. Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 28 4月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: NAdam Ford <aford173@gmail.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 14 4月, 2018 1 次提交
-
-
由 Jean-Jacques Hiblot 提交于
Those options are required to enable support for SATA on DRA7 platforms. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
-
- 12 4月, 2018 1 次提交
-
-
由 Marek Vasut 提交于
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all configurations using it to Kconfig. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Tom Rini <trini@konsulko.com>
-
- 09 4月, 2018 2 次提交
-
-
由 Alex Kiernan 提交于
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com> Reviewed-by: NLukasz Majewski <lukma@denx.de> Reviewed-by: NPetr Vorel <petr.vorel@gmail.com> Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
-
由 Alex Kiernan 提交于
This converts CONFIG_DRIVER_TI_CPSW to Kconfig Signed-off-by: NAlex Kiernan <alex.kiernan@gmail.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 08 4月, 2018 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 14 3月, 2018 1 次提交
-
-
由 Jean-Jacques Hiblot 提交于
Beside enabling the support for HS200 in mmc core, enabling the HS200 support in the SPL requires multi-dtb support in the SPL because pinctrl and IOdelays vary across SOCs. Also we need to make sure that the pinctrl properties arenot removed from the dts by setting CONFIG_OF_SPL_REMOVE_PROPS to remove only clocks and interrupts properties. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
-
- 23 2月, 2018 1 次提交
-
-
由 Tom Rini 提交于
A number of platforms include config_distro_defaults.h but do not enable CONFIG_DISTRO_DEFAULTS. As they plainly intended to, set that flag and re-sync config files. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 19 2月, 2018 1 次提交
-
-
由 Jean-Jacques Hiblot 提交于
By default UHS and HS200 are not enabled. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
-
- 23 1月, 2018 1 次提交
-
-
由 Adam Ford 提交于
This converts the following to Kconfig: CONFIG_OMAP_USB_PHY Signed-off-by: NAdam Ford <aford173@gmail.com>
-
- 17 10月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 11 10月, 2017 1 次提交
-
-
由 Tuomas Tynkkynen 提交于
Having this as a 'default y' is rather annoying because it doesn't actually compile unless other options are defined in the board header: ../cmd/bootm.c: In function 'do_imls_nor': ../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'? i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) { Make it 'default n' so people who develop new boards that start from a blank defconfig have one less compilation failure to debug. Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
-
- 04 10月, 2017 2 次提交
-
-
由 Maxime Ripard 提交于
Fastboot need a bunch of options to be operating properly, such as the g_dnl gadget, the fastboot command, and some options that make sense. Since fastboot is now part of Kconfig, make sure we have them right. That will also reduce the boilerplate in the defconfigs. Reviewed-by: NŁukasz Majewski <lukma@denx.de> Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
由 Maxime Ripard 提交于
The g_dnl USB settings for the vendor ID, product ID and manufacturer are actually common settings that can and should be shared by all the gadgets. Make them common by renaming them, and convert all the users. Reviewed-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NLukasz Majewski <lukma@denx.de> Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
-
- 30 9月, 2017 1 次提交
-
-
由 Tom Rini 提交于
On ARCH_OMAP2PLUS platforms we know what the DDR layout is going to be, and that it is safe to use SPL_STACK_R and provide a default value for it. select this and re-sync the defconfigs. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 12 9月, 2017 1 次提交
-
-
由 Lokesh Vutla 提交于
Add support for selecting proper dtb for dra76x u-boot from FIT. Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com> Reviewed-by: NTom Rini <trini@konsulko.com>
-
- 02 9月, 2017 1 次提交
-
-
由 Tom Rini 提交于
- Move ANDROID_IMAGE_SUPPORT to top level Kconfig under images as it's not strictly part of fastboot. - Add some defaults for the fastboot buffer location and size - Migrate all options listed in cmd/fastboot/Kconfig - Cleanup the README Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 28 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 27 8月, 2017 1 次提交
-
-
由 Semen Protsenko 提交于
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>
-
- 12 8月, 2017 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_SPL Note that trats does not actually use SPL, so this option can no-longer be set. Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
- 11 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 09 8月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Reviewed-by: NJoe Hershberger <joe.hershberger@ni.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 08 8月, 2017 1 次提交
-
-
由 Alexandru Gagniuc 提交于
Signed-off-by: NAlexandru Gagniuc <alex.g@adaptrum.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
- 01 8月, 2017 2 次提交
-
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
When we have MMC available we assume that we want to put the env as a file on FAT. Cc: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 26 7月, 2017 1 次提交
-
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_ENV_IS_IN_MMC CONFIG_ENV_IS_IN_NAND CONFIG_ENV_IS_IN_UBI CONFIG_ENV_IS_NOWHERE In fact this already exists for sunxi as a 'choice' config. However not all the choices are available in Kconfig yet so we cannot use that. It would lead to more than one option being set. In addition, one purpose of this series is to allow the environment to be stored in more than one place. So the existing choice is converted to a normal config allowing each option to be set independently. There are not many opportunities for Kconfig updates to reduce the size of this patch. This was tested with ./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC And then manual updates. This is because for CHAIN_OF_TRUST boards they can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic now. Signed-off-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 19 6月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-