- 25 1月, 2008 7 次提交
-
-
由 Becky Bruce 提交于
Signed-off-by: NBecky Bruce <becky.bruce@freescale.com>
-
由 Becky Bruce 提交于
This can be used for debug, and will be used by board code to help implement reginfo. Signed-off-by: NBecky Bruce <becky.bruce@freescale.com>
-
由 Becky Bruce 提交于
This includes mpc8610hpcd, mpc8641hpcn, and sbc8641d. Signed-off-by: NBecky Bruce <becky.bruce@freescale.com>
-
由 Becky Bruce 提交于
Signed-off-by: NBecky Bruce <becky.bruce@freescale.com>
-
由 Becky Bruce 提交于
Signed-off-by: NBecky Bruce <becky.bruce@freescale.com>
-
由 Becky Bruce 提交于
Adds the support code in cpu/mpc86xx for the new law setup code recently created fsl_law.c, and changes the MPC8641HPCN config to use this code. Signed-off-by: NBecky Bruce <becky.bruce@freescale.com>
-
由 Becky Bruce 提交于
* split the BAT initialization so that only 2 BATs (for the boot page and stack) are programmed very early on. The rest are initialized later. * Move other BAT setup, ccsrbar setup, and law setup later in the code after translation has been enabled. These changes will facilitate the moving of law and BAT initialization to C code, and will aid with 36-bit physical addressing support. Signed-off-by: NBecky Bruce <becky.bruce@freescale.com>
-
- 23 1月, 2008 15 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Wolfgang Denk 提交于
-
-
由 Wolfgang Denk 提交于
-
-
由 Wolfgang Denk 提交于
-
-
由 Wolfgang Denk 提交于
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
-
-
-
-
-
- 19 1月, 2008 1 次提交
-
-
由 Dave Liu 提交于
The commit 04a9e118 cause the 83xx immap broken, so the DMA and PCI will be failed. The patch fix the struct spi8xxx and rm struct spi83xx. Signed-off-by: NDave Liu <daveliu@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 18 1月, 2008 17 次提交
-
-
-
由 Haavard Skinnemoen 提交于
Add support for the ATNGW100 Network Gateway reference design, including flash, ethernet and MMC support. Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
-
由 Haavard Skinnemoen 提交于
I don't know why the relevant layers can't do this by itself, but this is what ppc does. Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
-
由 Michael Schwingen 提交于
Hi, The patch adds 4 boards, called AcTux-1 .. AcTux-4. This patch contains the files that contain changes for multiple boards, the board-specific files follow as separate patches. Signed-off-by: NMichael Schwingen <michael@schwingen.org>
-
由 Michael Schwingen 提交于
Signed-off-by: NMichael Schwingen <michael@schwingen.org>
-
由 Michael Schwingen 提交于
Signed-off-by: NMichael Schwingen <michael@schwingen.org>
-
由 Michael Schwingen 提交于
Signed-off-by: NMichael Schwingen <michael@schwingen.org>
-
由 Michael Schwingen 提交于
Signed-off-by: NMichael Schwingen <michael@schwingen.org>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
由 Michael Schwingen 提交于
enables the RTS signal with CONFIG_SERIAL_RTS_ACTIVE. No handshaking is done, but the active RTS signal allows to connect to the target using a PC which is using RTS/CTS handshake, and does no harm if the PC is set to ignore RTS. Signed-off-by: NMichael Schwingen <michael@schwingen.org>
-
allow to load the microde from flash or ram by download it through the serial or other. Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NStefan Roese <sr@denx.de>
-
由 Michael Schwingen 提交于
Hi, the following patch adds support to move the IXP42X NPE firmware to a separate flash block, whose start address is defined in CONFIG_IXP4XX_NPE_EXT_UCODE_BASE. Using that, it is possible to build NPE-enabled u-boot without copyright problems due to the NPE firmware. I hope the patch applies, I get whitespace-related differences in the NPE files due to trailing whitespace in the original versions. Signed-off-by: NMichael Schwingen <michael@schwingen.org> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
由 Andy Fleming 提交于
-
由 TsiChungLiew 提交于
Signed-off-by: NTsiChungLiew <Tsi-Chung.Liew@freescale.com> Signed-off by: John Rigby <jrigby@freescale.com>
-
由 TsiChungLiew 提交于
Signed-off-by: NTsiChungLiew <Tsi-Chung.Liew@freescale.com> Signed-off by: John Rigby <jrigby@freescale.com>
-
由 TsiChungLiew 提交于
Signed-off-by: NTsiChungLiew <Tsi-Chung.Liew@freescale.com> Signed-off-by: NBen Warren <biggerbadderben@gmail.com> Signed-off by: John Rigby <jrigby@freescale.com>
-
由 TsiChungLiew 提交于
Signed-off-by: NTsiChungLiew <Tsi-Chung.Liew@freescale.com> Signed-off by: John Rigby <jrigby@freescale.com>
-