The SD loader binary is now downloadable at

https://wiki.linaro.org/Boards/MX6QSabreLite

under a open-source 3-clause BSD license. Update the README
for this.

The discussion shows that it's hard to change the hardware
regarding the default SPI NOR boot of the SabreLite boards.
I.e. this will stay the default boot. Therefore remove the
'early version of' statement.
Signed-off-by: NDirk Behme <dirk.behme@de.bosch.com>
CC: Stefano Babic <sbabic@denx.de>
CC: Jason Liu <liu.h.jason@gmail.com>

This patch replaces the use of magice numbers for scratch register
addresses with earlier defined register definitions.
Signed-off-by: NRobert Delien <robert@delien.nl>

This patch adds register definitions for the registers of the DIGCTL
IP-block.
Signed-off-by: NRobert Delien <robert@delien.nl>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Configuring for zipitz2 board...
zipitz2.c: In function ‘board_mmc_init’:
zipitz2.c:85:2: warning: implicit declaration of function ‘pxa_mmc_register’ [-Wimplicit-function-declaration]
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

This link script seems old and incompatible with relocation and its
own sa1000 start.S file. It isn't used because the CPU's link script
was picked up in preference to this.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Acked-by: NKristoffer Ericson <kristoffer.ericson@gmail.com>

Say good bye to some ancient, very broken and unused code.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>

CONFIG_SYS_INIT_SP_ADDR points to RAM, but it's used before
DRAM controller init. Fix it by setting CONFIG_SYS_INIT_SP_ADDR
to SRAM
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>

* 'master' of git://git.denx.de/u-boot-cfi-flash:
  cfi: fix the incomplete erased status check in buffer write

* 'master' of git://git.denx.de/u-boot-nds32:
  nds32/n1213: correct vector table in start.S
  nds32: fix ptrace and interrupt register overflow

This reverts commit 295d3942.

It turns that this really doesn't work very nicely. Instead we should
have a pre-console panic function so that we know that further execution
is impossible and we don't need to worry about trampling on UARTs, etc.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NWolfgang Denk <wd@denx.de>

Without the fix, flash_write_cfibuffer will terminate the erased
status check once an all-0xFF word has been found instead of
continuing the erased status check utill the first non-0xFF word.
Signed-off-by: NTao Hou <hotforest@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: NStefan Roese <sr@denx.de>

Recent bootstage commits made the code grow, which caused linker
errors.  Adjust the linker script to fix that.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Correct definition of vector table in start.S
Signed-off-by: NMacpaul Lin <macpaul@gmail.com>

Fix ptrace and interrupt register overflow warning.
Add missing P0 and P1 (r26 and r27) into register lists.
These register are usually used in OS.
Signed-off-by: NMacpaul Lin <macpaul@gmail.com>

This patch adds FAT and ext2 command support for marvell gplugD
Signed-off-by: NAjay Bhargav <ajay.bhargav@einfochips.com>

This patch adds support for USB commands and USB storage device for
Marvell gplugD
Signed-off-by: NAjay Bhargav <ajay.bhargav@einfochips.com>

This patch adds support for USB EHCI driver for Armada100 SOCs.
Signed-off-by: NAjay Bhargav <ajay.bhargav@einfochips.com>

This patch adds USB host controller's UTMI PHY interface driver for
Armada100 SOCs.
Signed-off-by: NAjay Bhargav <ajay.bhargav@einfochips.com>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The dev->req_config flag was indicating that the forwarded
request needs to perform the usb gadget delayed status.
This is however not needed anymore, so it can be removed.
Signed-off-by: NLukasz Majewski <l.majewski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>

While receiving packets from FIFO sometimes the buffer provided was
nonaligned. Fix this by taking a temporary aligned buffer and then
copying the content to nonaligned buffer.
Signed-off-by: NShiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: NAmit Virdi <amit.virdi@st.com>

Signed-off-by: NAmit Virdi <amit.virdi@st.com>

This patch adds the support for usb device high speed for designware peripheral.
Signed-off-by: NVipin Kumar <vipin.kumar@st.com>
Signed-off-by: NAmit Virdi <amit.virdi@st.com>

This patch fixes a few bugs in USB device controller driver.
The fixes are as follows
1. Adding error condition checks eg. NULL return
2. Endpoint other than endpoint 0 (control endpoint) are initialized
only if usb state machine reaches STATE_ADDRESSED or above
3. Zero length packet handling corrected
4. Dead code removed
5. Bulk out endpoint returns after servicing 1 interrupt and returns
back to service if more interrupts are pending
Signed-off-by: NVipin Kumar <vipin.kumar@st.com>
Signed-off-by: NAmit Virdi <amit.virdi@st.com>
Acked-by: NMarek Vasut <marex@denx.de>

The earlier usb device controller driver was specific to spear platforms. This
patch implements the usb device controller driver as a generic controller which
can be reused by other platforms using this peripheral.
Signed-off-by: NVipin Kumar <vipin.kumar@st.com>
Signed-off-by: NAmit Virdi <amit.virdi@st.com>
Acked-by: NMarek Vasut <marex@denx.de>

Common code has a mdelay() func, so use that instead of the usb-specific
wait_ms() func.  This also fixes the build errors:

ohci-hcd.c: In function 'submit_common_msg':
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1519:9: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1816:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1827:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1844:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1563:11: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1583:9: sorry, unimplemented: called from here
make[1]: *** [ohci-hcd.o] Error 1
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NMarek Vasut <marex@denx.de>

musb_hcd.c: In function 'musb_submit_rh_msg':
musb_hcd.c:827:2: warning: format '%d' expects type 'int',
	but argument 3 has type 'long unsigned int'
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Add calls to bootstage before and after relocation, and just
before jumping to the OS.

The idea here is you can call bootstage_report() to get a report.
Additionally, if you define CONFIG_BOOTSTAGE_REPORT then a report is
printed automatically by U-Boot just before jumping to the kernel.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This inserts bootstage calls into tftp, usb start and bootm. We
could go further, but this is a reasonable start to illustrate
the concept.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This defines the basics of a new boot time measurement feature. This allows
logging of very accurate time measurements as the boot proceeds, by using
an available microsecond counter.

To enable the feature, define CONFIG_BOOTSTAGE in your board config file.
Also available is CONFIG_BOOTSTAGE_REPORT which will cause a report to be
printed just before handing off to the OS.

Most IDs are not named at this stage. For that I would first like to
renumber them all.

Timer summary in microseconds:
       Mark    Elapsed  Stage
          0          0  reset
    205,000    205,000  board_init_f
  6,053,000  5,848,000  bootm_start
  6,053,000          0  id=1
  6,058,000      5,000  id=101
  6,058,000          0  id=100
  6,061,000      3,000  id=103
  6,064,000      3,000  id=104
  6,093,000     29,000  id=107
  6,093,000          0  id=106
  6,093,000          0  id=105
  6,093,000          0  id=108
  7,089,000    996,000  id=7
  7,089,000          0  id=15
  7,089,000          0  id=8
  7,097,000      8,000  start_kernel
Signed-off-by: NSimon Glass <sjg@chromium.org>

These calls should not be made directly any more, since bootstage
will call the show_boot_...() functions as needed.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Define timer_get_boot_us() which returns the number of microseconds
since boot. If undefined then we use get_timer() * 1000.

We can fit this in a 32-bit register which keeps everyone happy on
the efficiency side. It will wrap around after about an hour. If we
are still looking at it after an hour then we had better not be
timing the boot.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This changes over all the FIT image progress numbers to use enums
from bootstage.h.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This changes over the network-related progress numbers to use enums
from bootstage.h.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This changes over the NAND progress numbers to use enums from
bootstage.h.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This changes over the IDE progress numbers to use enums from bootstage.h.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NSimon Glass <sjg@chromium.org>
Acked-by: NMike Frysinger <vapier@gentoo.org>