Move file ocelot_switch to mscc_eswitch to prepare to add
new net drivers for other MSCC SoCs.
Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com>

Testing has shown that the timer on the MT7688 platforms does not run
correctly (too fast timeout). This patch changes
CONFIG_SYS_MIPS_TIMER_FREQ from 200MHz to 290MHz which is the correct
value, as its also used in Linux.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>

When power cycle the Jaguar2 boards, it couldn't read the
phys, therefore it always deduce that the board type is
pcb111.

Add a small delay after setting the gpio pins, fix the
issue.
Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com>

Enable debug uart for Jaguar2 SoC family.
Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com>

- Add features and fixups to support video on Amlogic GX SoCs
- Add video support for Amlogic GX SoC
- Add DT fixups
- Enable Video and USB Console for libretech-cc board

libretech-cc being the main device tested with CONFIG_VIDEO_MESON, let's
enable it by default.

Also enable:
 - CONFIG_SYS_WHITE_ON_BLACK for prettiness
 - CONFIG_VIDEO_DT_SIMPLEFB for framebuffer sharing with kernel
Signed-off-by: NMaxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NAnatolij Gustschin <agust@denx.de>

With the recent addition of the meson VPU driver, enable the following
config entries by default for meson-64 targets: CONFIG_CONSOLE_MUX,
CONFIG_SYS_CONSOLE_IS_IN_ENV.

This allows outputting the console via video if CONFIG_VIDEO_MESON is
selected.
Signed-off-by: NMaxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NAnatolij Gustschin <agust@denx.de>

Allows displaying the console via video and using a USB keyboard.

Also enables CONFIG_SPLASH_SCREEN if using video.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NMaxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: NAnatolij Gustschin <agust@denx.de>

If VIDEO_MESON is enabled, we need to setup the fdt for the framebuffer.

Call meson_vpu_rsv_fb() which reserves the framebuffer memory region for
EFI, and sets up simple-framebuffer nodes if simplefb support is
enabled.
Signed-off-by: NMaxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NAnatolij Gustschin <agust@denx.de>

There's no reliable way to reuse the hhi entry from the vpu as is done
in the linux kernel, so we duplicate it here.

We will be able to sync against kernel DTS in the future when the VPU
gets based on the clock framework rather than the HHI reg.
Signed-off-by: NMaxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

The hdmi_5v regulator must be enabled to provide power to the physical HDMI
PHY and enables the HDMI 5V presence loopback for the monitor.

Fixes: b409f625a6d5 ("ARM64: dts: meson-gx: Add HDMI_5V regulator on selected boards")
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NKevin Hilman <khilman@baylibre.com>
[backport of linux commit e1f2163deac059ad39f07aba9e314ebe605d5a7a]

Flag the appropriate nodes with u-boot,dm-pre-reloc
Signed-off-by: NMaxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

This adds video output support for Amlogic GXBB/GXL/GXM chips.
The supported ports are CVBS and HDMI (based on DW_HDMI).

When using HDMI, only DMT modes are supported.

There is support for simple-framebuffer (CONFIG_VIDEO_DT_SIMPLEFB)
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NJorge Ramire-Ortiz <jramirez@baylibre.com>
Signed-off-by: NMaxime Jourdan <mjourdan@baylibre.com>
[narmstrong: fixed defines alignment in meson_canvas.c]
Reviewed-by: NAnatolij Gustschin <agust@denx.de>

Some IPs like the meson VPU can only feed a particular pixel format to
dw_hdmi. As of now, the driver is hardcoded to use RGB888 as input.

This commit enables different pixel format inputs, with the appropriate
CSC configuration.
Signed-off-by: NJorge Ramire-Ortiz <jramirez@baylibre.com>
Signed-off-by: NMaxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NAnatolij Gustschin <agust@denx.de>

Some IPs like the meson VPU have a specific way to write to dw_hdmi
registers. Make it configurable.
Signed-off-by: NJorge Ramirez-Ortiz <jramirez@baylibre.com>
[added commit description]
Signed-off-by: NMaxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NAnatolij Gustschin <agust@denx.de>

MESON_GX_VPU_POWER_DOMAIN should depend on POWER_DOMAIN.
Signed-off-by: NMaxime Jourdan <mjourdan@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NAnatolij Gustschin <agust@denx.de>

Add entry for Amlogic SoC maintained files and the freshly
created mailing-list.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>

If `make mrproper` does not delete the generated drivers/video/fonts/*.S
files a following `make tests` fails.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NAnatolij Gustschin <agust@denx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This unbreaks dfu mmc_file_op which is currently broken since using the
load cmd on a buffer from heap is not allowed - added with
commit aa3c609e ("fs: prevent overwriting reserved memory")

Fixes: commit aa3c609e ("fs: prevent overwriting reserved memory")
Reported-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLukasz Majewski <lukma@denx.de>

- Enable DM_MMC support

Enable DM_MMC for all Allwinner SoCs, this will eventually
enable BLK.

Also removed DM_MMC enablement in few parts of sunxi
configurations.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

Like other Allwinner A64 boards, pinebook also need altering
auto-numbering of mmc2 to mmc1 which is available in common
sunxi dsti file, sunxi-u-boot.dtsi

Pinebook has a separate sun50i-a64-pinebook-u-boot.dtsi which
takes more precedence for u-boot.dtsi inclusion and it eventually
failed to include the sunxi-u-boot.dtsi.

So, this patch add support to include the sunxi-u-boot.dtsi in the
sun50i-a64-pinebook-u-boot.dtsi
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Tested-by: Vasily Khoruzhick <anarsoul@gmail.com> # Pinebook

Environment and fastboot mmc devices are configured based on the number
of mmc slots defined on particular board configs, MMC_SUNXI_SLOT_EXTRA.

If MMC_SUNXI_SLOT_EXTRA is more than 1, the default env and fastboot
mmc devices is mmc1 by assuming mmc0 is SD and mmc1 is emmc device.

But with DM_MMC the mmc devices are numbered as per the dts node
enablement. If there is a chance of having enabling all mmc nodes
in dts say mmc0, mmc1, mmc2 then the default env and fastboot devices
will failed to assign proper emmc device since mmc2 is emmc in most
of the Allwinner platforms.

So, we need to alter the auto-numbering by aliasing mmc2 to mmc1 since
aliases take precedence over auto-numbering.

If the dts enables mmc0, mmc1, mmc2, then all the nodes will probe
sequentially and auto-numbered as it is. but when aliases mmc1 with mmc2
the resulting number should be that mmc0 is till mmc0, mmc2 become mmc1
and mmc2 become mmc1

Without aliases of mmc1 = &mmc2;
-------------------------------
MMC:   mmc@1c0f000: 0, mmc@1c10000: 1, mmc@1c11000: 2

With aliases of mmc1 = &mmc2;
----------------------------
MMC:   Device 'mmc@1c11000': seq 1 is in use by 'mmc@1c10000'
mmc@1c0f000: 0, mmc@1c10000: 2, mmc@1c11000: 1
Loading Environment from FAT... OK

Some platforms like A20 has mmc0...mmc3, but there is no usecases now
for enabling all mmc controllers in any of A20 board dts files.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Some Allwinner clock devices have parent clocks and reset gates itself,
which need to be activated for them to work.

Add some code to just assert all resets and enable all clocks given.
This should enable the A80 MMC config clock, which requires both to be
activated. The full CCU devices typically don't require resets, and have
just fixed clocks as their parents. Since we treat both as optional and
enabling fixed clocks is a NOP, this works for all cases, without the need
to differentiate between those clock types.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Acked-by: NJagan Teki <jagan@openedev.com>

For 2019.04

If a board DT describes a cd-gpios property, but also marks the storage
as non-removable, we must ignore the GPIO (as Linux does).

Teach the DM_MMC part of the Allwinner MMC driver about the
non-removable DT property, to fix DM_MMC access on the SoPine and
Pine64-LTS board.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Acked-by: NJagan Teki <jagan@openedev.com>

Enabling DM_MMC skips the call to mmc_pinmux_setup() in board.c, as this
is supposed to be handled by the MMC driver, using DT information.

However we don't have a pinctrl driver yet, but would still like to keep
the working pinmux setup for our MMC devices. So bring this particular
call back to the DM_MMC code flow.

When booting from either SD card or eMMC, the SPL does the setup for us,
but when booting from SPI or USB we must not skip this part.

Fixes, boot via FEL or SPI flash, where the SPL won't setup the pinmux
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Acked-by: NJagan Teki <jagan@openedev.com>
[jagan: add Fix details on commit message]
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Now that we have the gate clocks and the reset gates in our new
Allwinner clock driver, let's make use of them in the MMC driver, when
DM_MMC is defined.
We treat the reset device as optional now, as the older SoCs don't
implement it.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NJagan Teki <jagan@openedev.com>

A80 gates clock already be part of CLK framework, so just
add mod_clk offset with A80 compatible string.

Cc: Rask Ingemann Lambertsen <rask@formelder.dk>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>

Unlike other Allwinner SoC's, H6 uses a different MMC mod clock offset.
Connect that with the respective compatible string.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

Add MMC compatible strings for A83T, A64, H5.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>

The A80 handles resets and clock gates for the MMC devices differently,
outside of the CCU IP block. Consequently we have a separate clock
device with a separate binding for that.

Implement that with the respective clock gates and resets to allow the
A80 taking part in the DM_MMC game.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
[jagan: fix a80 mmc clock config compatible]
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NJagan Teki <jagan@openedev.com>

Add the MMC clock gates and reset bits for all the Allwinner SoCs.
This allows them to be used by the MMC driver.

We don't advertise the mod clock yet, as this is still handled by the
MMC driver.
Signed-off-by: NAndre Przywara <andre.przywara@arm.com>
[jagan: add V3S, A80 gates/resets]
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Reviewed-by: NJagan Teki <jagan@openedev.com>

Enable USB host controllers for Amarula A64-Relic board,
the respective nodes are already present in DTS.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Update generation of spl binaries
- continue to generate all SPL files in spl sub-directory
- copy in root folder the needed file for user (YOCTO, buildroot):
  u-boot-spl.stm32
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>

Adds pinconf support for the Amlogic pinctrl driver (fixed)

Adding pinconf support is necessary to enable boot from SPI
without breaking the eMMC. When booting from SPI, the ROM code
leave pull downs on the eMMC pad.

We need to set pinconf provided in DT to solve this
Signed-off-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
[narmstrong: added missing comma in pinctrl-meson-axg-pmx.c]

This patch enables Falcon Mode by default and updates the README
file to show instructions on how to run from the micro SD card
or eMMC.  This patch also enables fatwrite to help assist with
writing the 'args' to the microSD card.
Signed-off-by: NAdam Ford <aford173@gmail.com>

With the updated device trees in place, this patch enables
DM_USB which uses several regulators also enabled with this patch.
Signed-off-by: NAdam Ford <aford173@gmail.com>

The i.MX6 SOM and development kits have undergone significant
updates and changes over the past few months.  This re-sync's
the U-Boot with Logic PD's BSP.
Signed-off-by: NAdam Ford <aford173@gmail.com>