- 16 11月, 2017 1 次提交
-
-
由 VlaoMao 提交于
Increase size PCI memory mapping from 32MiB to 128MiB. Signed-off-by: NVlaoMao <vlaomao@gmail.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
- 14 11月, 2017 1 次提交
-
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 13 11月, 2017 3 次提交
-
-
由 Soeren Moch 提交于
This reverts commit c61d0009. A tbs2910 board user reported a very slow console frambuffer as regression in current u-boot. I could bisect this down to the above mentioned commit. This revert brings back the fast framebuffer console (one cache flush per string in puts(), not after each char). Reported-by: NUwe Scheffler <scheffler.u@web.de> Signed-off-by: NSoeren Moch <smoch@web.de> Tested-by: NUwe Scheffler <scheffler.u@web.de> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Angelo Dureghello 提交于
Signed-off-by: NAngelo Dureghello <angelo@sysam.it>
-
由 Marek Vasut 提交于
The eMMC is 1V8 device only and the signaling is always 1V8, fix the DT for Salvator-X/XS to describe the hardware correctly. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
- 10 11月, 2017 7 次提交
-
-
-
由 Werner Böllmann 提交于
After updating u-boot from v2016.01 to 2017.09, issue with "SATA link 0 timeout." on my Cubietruck board. mdelay milled after moving satapwr code to board. "sunxi: Turn satapwr on from board_init" (sha1: 9fbb0c3a) After adding the "mdelay(500);" line that was lost in the path the error is gone. Signed-off-by: NWerner Böllmann <Werner.Boellmann@fh-dortmund.de> [Rebased and updated change and commit message] Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Chen-Yu Tsai 提交于
Only the H3/H5 SoCs have an internal PHY and its related clock and reset controls. Use an #ifdef to guard the internal PHY control code block so it can be built for other SoCs, such as the A83T or A64. Signed-off-by: NChen-Yu Tsai <wens@csie.org> Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: NJoe Hershberger <joe.hershberger@ni.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
-
由 Jagan Teki 提交于
Update the falcon offsets for args to 16MB and kernel to 17MB Since the below commit updated U-Boot proper location along with rockchip boot image offsets "spl: set SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR to 0x4000 for rockchip" (sha1: 8f4d62b4) Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Jagan Teki 提交于
This patch fixed U-Boot proper location has been missed to update in bewlo commit "rockchip: doc: update U-Boot location info" (sha1: 73e6dbe8) Signed-off-by: NJagan Teki <jagan@amarulasolutions.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Goldschmidt Simon 提交于
The U-Boot location has been moved to block 16384. This is 8MB, not 4MB. Signed-off-by: NSimon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com> Reviewed-by: NJagan Teki <jagan@openedev.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
- 09 11月, 2017 10 次提交
-
-
-
-
由 Lukasz Majewski 提交于
Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
This commit provides support for LWN's IMX6Q based DISPLAY5 board. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
This commit provides generic function to set the RGMII/HSIC IO voltage level on iMX6 devices. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Lukasz Majewski 提交于
The sys_proto.h file has been included earlier in this file. Signed-off-by: NLukasz Majewski <lukma@denx.de>
-
由 Artturi Alm 提交于
due misnaming of CONFIG_SUN4I_EMAC in include/configs/sunxi-common.h, likely missed in: commit 3146f0c0 ("Move PHYLIB to Kconfig") Signed-off-by: NArtturi Alm <artturi.alm@gmail.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Artturi Alm 提交于
fixes CONFIG_SUNXI_EMAC references from drivers/net/Makefile and include/configs/sunxi-common.h likely forgotten in: commit abc3e4df ("sunxi: Convert SUNXI_EMAC to Kconfig") Signed-off-by: NArtturi Alm <artturi.alm@gmail.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
- 07 11月, 2017 18 次提交
-
-
由 Benoît Thébaudeau 提交于
The following error has been observed on i.MX25 with a high-speed SDSC card: Data Write Failed in PIO Mode. It was caused by the timeout set on PRSSTAT.BWEN, which was triggered because this bit takes 15 ms to be set after writing the first block to DATPORT with this card. Without this timeout, all the blocks are properly written. This timeout was implemented by decrementing a variable, so it was depending on the CPU frequency. Fix this issue by setting this timeout to a long enough absolute duration (500 ms). Signed-off-by: NBenoît Thébaudeau <benoit.thebaudeau.dev@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
由 Jagan Teki 提交于
- Update newly added include/configs file in MAINTAINERS - Update newly added defconfig file in README Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
-
由 Fabio Estevam 提交于
When a high speed card is connected to mx51evk the following error is seen: U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200) CPU: Freescale i.MX51 rev3.0 at 800 MHz Reset cause: POR Board: MX51EVK DRAM: 512 MiB MMC: FSL_SDHC: 0, FSL_SDHC: 1 *** Warning - read failed, using default environment In: serial Out: serial Err: serial Net: FEC Hit any key to stop autoboot: 0 => saveenv Saving Environment to MMC... Writing to MMC(0)... failed The root cause for the failure is the eSDHC-A001 erratum: "eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 0x4,0x8, and 0xC" that is listed on some PowerArchitecture chips: https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf Even though eSDHC-A001 is not documented on the i.MX51 errata document, I have confirmed with the NXP design team that this erratum does affect i.MX51, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001 at SoC level. The i.MX51 ts4800 board already selects this option, but it is better to move this selection to the i.MX51 SoC level instead. Successfully tested with a high speed SD card on a mx51evk board. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com> Acked-by: NSebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
-
由 Fabio Estevam 提交于
When a high speed card is connected to mx25 the following error is seen: U-Boot 2017.11-rc2-00104-gb79372ae (Oct 31 2017 - 11:02:22 -0200) CPU: Freescale i.MX25 rev1.2 at 399 MHz Reset cause: POR Board: MX25PDK I2C: ready DRAM: 64 MiB No arch specific invalidate_icache_all available! MMC: FSL_SDHC: 0 *** Warning - read failed, using default environment In: serial Out: serial Err: serial Net: FEC Hit any key to stop autoboot: 0 => saveenv Saving Environment to MMC... Writing to MMC(0)... failed , which prevents any usage of the SD card. The root cause for the failure is the eSDHC-A001 erratum: "eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 0x4,0x8, and 0xC" that is listed on some PowerArchitecture chips: https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf Even though eSDHC-A001 is not documented on the i.MX25 errata document, I have confirmed with the NXP design team that this erratum does affect i.MX25, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001 at SoC level. Successfully tested with a high speed SD card on a mx25pdk board. Suggested-by: NBenoît Thébaudeau <benoit@wsystem.com> Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com> Acked-by: NSebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Acked-by: NOtavio Salvador <otavio@ossystems.com.br> Tested-by: Otavio Salvador <otavio@ossystems.com.br> # mx25pdk
-
由 Fabio Estevam 提交于
The motivation for moving MX25 selection to Kconfig is to be able to better handle MX25 specific errata, so that an errata option can be selected at SoC level instead of board level. This selection method also aligns with the way other i.MX SoCs are selected in U-Boot. Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com> Acked-by: NSebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com> Reviewed-by: NBenoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
-
由 Kever Yang 提交于
Use default value 0x4000 for SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR instead of define a new one. Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Kever Yang 提交于
Update rockchip U-Boot location to 0x4000/16384. Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Kever Yang 提交于
Rockchip use a 'loader2' partition for U-Boot, so u-boot.bin or u-boot.itb load by SPL need to locate at0x4000. Detail here: http://opensource.rock-chips.com/wiki_Boot_optionSigned-off-by: NKever Yang <kever.yang@rock-chips.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Klaus Goger 提交于
The environment storage location is selectable via Kconfig. We support eMMC, SD and SPI-NOR as location for U-Boot. This adds support to store the environment in the SPI-NOR additional to the default eMMC location. Signed-off-by: NKlaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Klaus Goger 提交于
The VCC_SD and VCC_SDIO rail should only be powered up to 3.0V on RK3399 platforms. Signed-off-by: NKlaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Klaus Goger 提交于
pinctrl/rockchip.h provides defines that map pin numbers to pin names. Use them to make the dts more human readable. Signed-off-by: NKlaus Goger <klaus.goger@theobroma-systems.com> Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Philipp Tomsich 提交于
This change updates the USB configuration for the RK3399-Q7 in the DTS: * fixes the OTG board configuration by enabling it ('okay') * improves the speed of 'usb start' by disabling the unused EHCI/OHCI controllers Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: NKlaus Goger <klaus.goger@theobroma-systems.com>
-
由 Philipp Tomsich 提交于
To correctly model the usbhub_enable regulator for U-Boot, we need to change the settings to: * the GPIO polarity is GPIO_ACTIVE_LOW * should be set to inactive (enable-active-low) when boot-on settings are applied * it can be changed at runtime (i.e. remove the always-on) Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: NKlaus Goger <klaus.goger@theobroma-systems.com>
-
由 Philipp Tomsich 提交于
The fixed regulator for overriding BIOS_DISABLE had been modelling backwards (i.e. the GPIO polarity and the enable-active-low/high property had both been inverted), causing the 'regulator' command to always print/expect 'disabled'/'enabled' backwards. This fixes the mix-up and models it correctly: * the GPIO is low-active * the regulator should be enabled (enable-active-high) during boot-on initialisation Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Tested-by: NKlaus Goger <klaus.goger@theobroma-systems.com>
-
由 Kever Yang 提交于
All Rockchip SoCs use 32KB as CONFIG_ENV_SIZE. Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Kever Yang 提交于
Using the ENV offset from rockchip legacy U-Boot for all SoCs, the offset is 4MB-32KB Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Kever Yang 提交于
We use the same default ENV setting in rockchip_common.h for all SoC. Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@konsulko.com>
-