- 06 12月, 2014 1 次提交
-
-
由 Shengzhou Liu 提交于
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC. T1024RDB board Overview ----------------------- - T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz - CoreNet fabric supporting coherent and noncoherent transactions with prioritization and bandwidth allocation - 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support - Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC - Ethernet interfaces: - Two 10M/100M/1G RGMII ports on-board - one 10Gbps XFI interface - PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors. - SerDes: 4 lanes up to 10.3125GHz - IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD - eSPI: 64MB N25Q512 SPI flash. - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) - USB: Two Type-A USB2.0 ports with internal PHY - eSDHC: Support SD, SDHC, SDXC and MMC/eMMC - I2C: Four I2C controllers - UART: Two UART serial ports Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com> [York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT Fix Kconfig by adding SUPPORT_SPL] Reviewed-by: NYork Sun <yorksun@freescale.com>
-
- 23 4月, 2014 4 次提交
-
-
由 Shengzhou Liu 提交于
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework. PBL initializes the internal CPC-SRAM and copy SPL(160K) to it, SPL further initializes DDR using SPD and environment and copy u-boot(768K) from SPI/SD/NAND to DDR, finally SPL transfers control to u-boot. Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Shengzhou Liu 提交于
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework. PBL initializes the internal CPC-SRAM and copy SPL(160K) to it, SPL further initializes DDR using SPD and environment and copy u-boot(768 KB) from SPI/SD/NAND to DDR, finally SPL transfers control to u-boot. Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com> [York Sun: fix boards.cfg for T2081QDS_SDCARD and _SPIFLASH] Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Prabhakar Kushwaha 提交于
Add support of 2 stage NAND, SD, SPI boot loader using SPL framework. here, PBL initialise the internal SRAM and copy SPL(160KB). This further initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR. Finally SPL transer control to u-boot. Initialise/create followings required for SPL framework - Add spl.c which defines board_init_f, board_init_r - update tlb and ddr accordingly Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-
由 Prabhakar Kushwaha 提交于
Add support of 2 stage NAND boot loader using SPL framework. here, PBL initialise the internal SRAM and copy SPL(160KB). This further initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR. Finally SPL transer control to u-boot. Initialise/create followings required for SPL framework - Add spl.c which defines board_init_f, board_init_r - update tlb and ddr accordingly Signed-off-by: NPrabhakar Kushwaha <prabhakar@freescale.com> Reviewed-by: NYork Sun <yorksun@freescale.com>
-