- 28 11月, 2009 2 次提交
-
-
由 Po-Yu Chuang 提交于
This patch adds support for A320 evaluation board from Faraday. This board uses FA526 processor by default and has 512kB and 32MB NOR flash, 64M RAM. FA526 is an ARMv4 processor and uses the ARM920T source in this patch. Signed-off-by: NPo-Yu Chuang <ratbert@faraday-tech.com>
-
由 Sekhar Nori 提交于
Integrate DA830 EVM support into U-Boot. Provides initial support for TI OMAP-L137/DA830 SoC devices on a Spectrum Digital EVM board. See http://www.spectrumdigital.com/Signed-off-by: NNick Thompson <nick.thompson@gefanuc.com>
-
- 31 10月, 2009 1 次提交
-
-
由 Wolfgang Grandegger 提交于
This patch adds support for the board IPEK01 based on the MPC5200. The Futjitsu Lime graphics controller is configured in 16 bpp mode. Signed-off-by: NWolfgang Grandegger <wg@denx.de>
-
- 28 10月, 2009 1 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 24 10月, 2009 1 次提交
-
-
由 Tom Rix 提交于
Start of support of Texas Instruments Software Development Platform(SDP) for OMAP3430 - SDP3430 Highlights of this platform are: Flash Memory devices: Sibley NOR, Micron 8bit NAND and OneNAND Connectivity: 3 UARTs and expanded 4 UART ports + IrDA Ethernet, USB Other peripherals: TWL5030 PMIC+Audio+Keypad VGA display Expansion ports: Memory devices plugin boards (PISMO) Connectivity board for GPS,WLAN etc. Completely configurable boot sequence and device mapping etc. Support default jumpering and: - UART1/ttyS0 console(legacy sdp3430 u-boot) - UART3/ttyS2 console (matching other boards, and SDP HW docs) - Ethernet - mmc0 - NOR boot Currently the UART1 is enabled by default. for compatibility with other OMAP3 u-boot platforms, enable the #define of CONSOLE_J9. Conflicts: Makefile Fixed the conflict with smdkc100_config by moving omap_sdp3430_config to it is alphabetically sorted location above zoom1. Signed-off-by: NDavid Brownell <david-b@pacbell.net> Signed-off-by: NNishanth Menon <nm@ti.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
- 19 10月, 2009 3 次提交
-
-
由 Sandeep Paulraj 提交于
This patch adds support for the leopard board which is based on the DM355 SOC. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sandeep Paulraj 提交于
This patch adds the initial support for DM6467 EVM. Other features like NET and NAND support will be added as follow up patches. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Mike Frysinger 提交于
The majority of the time that I build things in U-Boot, I want to just build for the board. I don't make board config tweaks after selecting the board. So add a new pattern rule that allows people to combine two steps in one go: `make foo_config && make` => `make foo` This shouldn't conflict with any existing make rules as the pattern rule is used only the rule doesn't already exist. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 16 10月, 2009 2 次提交
-
-
由 Dipen Dudhat 提交于
On Chip BootROM support for P1 and P2 series RDB platforms. This patch is derived from latest On Chip BootROM support on MPC8536DS Signed-off-by: NDipen Dudhat <dipen.dudhat@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Dipen Dudhat 提交于
NAND Boot support for P1 and P2 series RDB platforms. This patch is derived from NAND Boot support on MPC8536DS. Signed-off-by: NDipen Dudhat <dipen.dudhat@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 14 10月, 2009 1 次提交
-
-
由 Minkyu Kang 提交于
Adds new board SMDKC100 that uses s5pc100 SoC Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com> Signed-off-by: NHeungJun, Kim <riverful.kim@samsung.com>
-
- 13 10月, 2009 3 次提交
-
-
由 Simon Kagstrom 提交于
The implementation is borrowed from the sheevaplug board and the Marvell 1.1.4 code. Unsupported (or untested) is the SD card, PCIe and SATA. Signed-off-by: NSimon Kagstrom <simon.kagstrom@netinsight.net>
-
由 Tom Rix 提交于
these boards are built around Atmel's AT91SAM9260/9G20 and have up to 64MB of NOR flash, up to 128MB of SDRAM, up to 2GB of NAND and include a 10/100 Ethernet PHY in RMII mode. Signed-off-by: NEric Benard <eric@eukrea.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
由 Tom Rix 提交于
CPUAT91 is built around Atmel's AT91RM9200 and has up to 16MB of NOR flash, up to 128MB of SDRAM, and includes a Micrel KS8721 PHY in RMII mode. Signed-off-by: NEric Benard <eric@eukrea.com> Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
-
- 30 9月, 2009 2 次提交
-
-
由 Mingkai Hu 提交于
The MPC8536E is capable of booting from the on-chip ROM - boot from eSDHC and boot from eSPI. When power on, the porcessor excutes the ROM code to initialize the eSPI/eSDHC controller, and loads the mian U-Boot image from the memory device that interfaced to the controller, such as the SDCard or SPI EEPROM, to the target memory, e.g. SDRAM or L2SRAM, then boot from it. The memory device should contain a specific data structure with control word and config word at the fixed address. The config word direct the process how to config the memory device, and the control word direct the processor where to find the image on the memory device, or where copy the main image to. The user can use any method to store the data structure to the memory device, only if store it on the assigned address. The on-chip ROM code will map the whole 4GB address space by setting entry0 in the TLB1, so the main image need to switch to Address space 1 to disable this mapping and map the address space again. This patch implements loading the mian U-Boot image into L2SRAM, so the image can configure the system memory by using SPD EEPROM. Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Mingkai Hu 提交于
MPC8536E can support booting from NAND flash which uses the image u-boot-nand.bin. This image contains two parts: a 4K NAND loader and a main U-Boot image. The former is appended to the latter to produce u-boot-nand.bin. The 4K NAND loader includes the corresponding nand_spl directory, along with the code twisted by CONFIG_NAND_SPL. The main U-Boot image just like a general U-Boot image except the parts that included by CONFIG_SYS_RAMBOOT. When power on, eLBC will automatically load from bank 0 the 4K NAND loader into the FCM buffer RAM where CPU can execute the boot code directly. In the first stage, the NAND loader copies itself to RAM or L2SRAM to free up the FCM buffer RAM, then loads the main image from NAND flash to RAM or L2SRAM and boot from it. This patch implements the NAND loader to load the main image into L2SRAM, so the main image can configure the RAM by using SPD EEPROM. In the first stage, the NAND loader copies itself to the second to last 4K address space, and uses the last 4K address space as the initial RAM for stack. Obviously, the size of L2SRAM shouldn't be less than the size of the image used. If so, the workaround is to generate another image that includes the code to configure the RAM by SPD and load it to L2SRAM first, then relocate the main image to RAM to boot up. Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 29 9月, 2009 1 次提交
-
-
由 Kyungmin Park 提交于
Refactoring the OneNAND IPL code and some minor fixed: - Remove unnecessary header file - Fix wrong access at read interrupt - The recent OneNAND has 4KiB pagesize Also Board can override OneNAND IPL image Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
-
- 26 9月, 2009 1 次提交
-
-
由 Paul Gortmaker 提交于
Commit 804d83a5 allows us to move all the configuration variation tweaks out of the top level Makefile and down into the board config header. This takes advantage of that for the sbc8349 board. Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 25 9月, 2009 6 次提交
-
-
由 Paul Gortmaker 提交于
Commit 804d83a5 allows us to move all the configuration variation tweaks out of the top level Makefile and down into the boards config header. This takes advantage of that for the sbc8540/sbc8560 boards. There were a couple of cheezy comments pointing at incorrect files, or files that don't exist, so I've cleaned those up too. Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Paul Gortmaker 提交于
Prior to this commit, to enable PCI, you had to go manually edit the board config header, and if you had 33MHz PCI, you had to manually change CONFIG_SYS_NS16550_CLK too, which was not real user friendly, This adds the typical PCI and clock speed make targets to the toplevel Makefile in accordance with what is being done with other boards (i.e. using the "-t" to mkconfig). Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Mingkai Hu 提交于
Signed-off-by: NMingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 14 9月, 2009 1 次提交
-
-
由 Michal Simek 提交于
Users should use microblaze-generic platform. This platform is longer not supported. Signed-off-by: NMichal Simek <monstr@monstr.eu>
-
- 11 9月, 2009 3 次提交
-
-
由 Dirk Eibach 提交于
Signed-off-by: NDirk Eibach <eibach@gdsys.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Prafulla Wadaskar 提交于
This patch adds support for "kwbimage" (Kirkwood Boot Image) image types to the mkimage code. For details refer to docs/README.kwbimage This patch is tested with Sheevaplug board Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com> Acked-by: NRon Lee <ron@debian.org> Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>
-
由 Wolfgang Denk 提交于
Commit 65f6f07b added support for the atmel_df_pow2 standalone program but missed to add a rule to remove it to the "clean" make target. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 05 9月, 2009 5 次提交
-
-
由 Sandeep Paulraj 提交于
This patch adds support for the DM365 EVM. It has been tested on a DM365 EVM. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Frederik Kriewitz 提交于
This patch adds support for the DevKit8000 board. Signed-off-by: NFrederik Kriewitz <frederik@kriewitz.eu>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 02 9月, 2009 4 次提交
-
-
由 Harald Krapfenbauer 提交于
The CM-BF537U is similar to the CM-BF537E module, but enough to need its own board port. Signed-off-by: NHarald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at> Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Albin Tonnerre 提交于
The Calao TNY-A9260 and TNY-9G20 are boards manufactured and sold by Calao Systems <http://www.calao-systems.com>. Their components are very similar to the AT91SAM9260EK board, so their configuration is based on the configuration of this board. There are however some differences: different clocks, no LCD, no ethernet. They also can use SPI EEPROM to store the environment. Signed-off-by: NAlbin Tonnerre <albin.tonnerre@free-electrons.com> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
由 Albin Tonnerre 提交于
The Calao SBC35-A9G20 board is manufactured and sold by Calao Systems <http://www.calao-systems.com>. It is built around an AT91SAM9G20 ARM SoC running at 400MHz. It features an Ethernet port, an SPI RTC backed by an onboard battery , an SD/MMC slot, a CompactFlash slot, 64Mo of SDRAM, 256Mo of NAND flash, two USB host ports, and an USB device port. More informations can be found at <http://www.calao-systems.com/articles.php?lng=en&pg=5936> Signed-off-by: NAlbin Tonnerre <albin.tonnerre@free-electrons.com>
-
由 Ilya Yanok 提交于
This patch adds support for i.MX27-LITEKIT development board from LogicPD. This board uses i.MX27 SoC and has 2MB NOR flash, 64MB NAND flash, FEC ethernet controller integrated into i.MX27. Signed-off-by: NIlya Yanok <yanok@emcraft.com> Acked-by: NWolfgang Denk <wd@denx.de>
-
- 01 9月, 2009 1 次提交
-
-
由 Wolfgang Denk 提交于
Update CHANGELOG Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 29 8月, 2009 2 次提交
-
-
由 Poonam Aggrwal 提交于
P1011 and P2010 are single core variants of P1010 and P2020 respectively. The board(RDB) will be same. Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Poonam Aggrwal 提交于
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-