This callback is used to send the 74 clock cycles after power up.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

When the clock is applied, compute the actual value of the clock. It may be
slightly different from the requested value (max freq, divisor threshold)
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

The default configuration is usually working fine for the the HS modes.
Don't enforce the presence of a dedicated pinmux for the HS modes.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

AM572x SR1.1 requires different IODelay values to be used than that used
in AM572x SR2.0. These values are populated in device tree. Add
capability in omap_hsmmc driver to extract IOdelay values for different
silicon revision. The maximum frequency is also reduced when using a ES1.1.
To keep the ability to boot both revsions with the same dtb, those values
can be provided by the platform code.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met.

Add support to parse mux values and iodelay values from device tree
and set these depending on the enumerated MMC mode.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

Add a new API to perform iodelay recalibration without isolate
io to be used in uboot.

The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met. The MMC driver can use the new API to
set the IO delay values depending on the MMC mode.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

Use the mmc_of_parse library function to populate mmc_config instead of
repeating the same code in host controller driver.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

>From OMAP3 SoCs (OMAP3, OMAP4, OMAP5, AM572x, AM571x), the DAT/CMD lines
reset procedure section in TRM suggests to first poll the SRD/SRC bit
until it is set to 0x1. But looks like that bit is never set to 1 and there
is an observable delay of 1sec everytime the driver tries to reset DAT/CMD.
(The same is observed in linux kernel).

Reduce the time the driver waits for the controller to set the SRC/SRD bits
to 1 so that there is no observable delay.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

According to errata i802, DCRC error interrupts
(MMCHS_STAT[21] DCRC=0x1) can occur during the tuning procedure.

The DCRC interrupt, occurs when the last tuning block fails
(the last ratio tested). The delay from CRC check until the
interrupt is asserted is bigger than the delay until assertion
of the tuning end flag. Assertion of tuning end flag is what
masks the interrupts. Because of this race, an erroneous DCRC
interrupt occurs.

The suggested  workaround is to disable DCRC interrupts during
the tuning procedure which is implemented here.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

HS200/SDR104 requires tuning command to be sent to the card. Use
the mmc_send_tuning library function to send the tuning
command and configure the internal DLL.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

In order to enable DDR mode, Dual Data Rate mode bit has to be set in
MMCHS_CON register. Set it here.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

Use the timing parameter set in the MMC core to set the
mode in UHSMS  bit field. This is in preparation for
adding HS200 support in omap hsmmc driver.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

"ti,dual-volt" is used in linux kernel to set the voltage capabilities.
For host controller dt nodes that doesn't have "ti,dual-volt",
it's assumed 1.8v is the io voltage. This is not always true (like in
the case of beagle-x15 where the io lines are connected to 3.3v).
Hence if "no-1-8-v" property is set, io voltage will be set to 3v.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

No functional change. Move bus width configuration setting to a
separate function and invoke it only if there is a change in the
bus width.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

Add a separate function for starting the clock, stopping the clock and
setting the clock. Starting the clock and stopping the clock can
be used irrespective of setting the clock (For example during iodelay
recalibration).
Also set the clock only if there is a change in frequency.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>

Use pr_* log functions from Linux.  They can be enabled/disabled
via CONFIG_LOGLEVEL.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>
Reviewed-by: NJaehoon Chung <jh80.chung@samsung.com>

The 'reset' command did not work on Porter because the reset code
was accessing the wrong PMIC address over broken I2C bus driver.
Replace the code with DM-aware code and fix up the PMIC address.
This makes the 'reset' command work again.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Get rid of the SH I2C driver on Porter and enable the IIC driver
instead . The old SH I2C is completely broken on Porter anyway
and the DM/DT capable IIC driver allows access to the PMIC too.
Use the DM/DT capable driver instead.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Enable I2C6 bus on Porter to access the PMIC , ie. to reset the board.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

The IIC on Gen2 is compatible with this driver as well, allow it.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Set those limits to inform U-Boot about FDT and initramfs placement.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Enable cache and time commands, which are convenience tools for
doing benchmarks and various boot tests. Also enable FIT support
for booting fitImage.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Toggle the PHY reset GPIO to bring the ethernet PHY out of reset properly.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: This should be moved to the SH ethernet driver, but it's quite
      late in the cycle, so this is something to be done in 2018.05.

Fix ommission where the u-boot,dm-pre-reloc DT bit was pulled into the
common DT, not the U-Boot specific DT part. Move it to U-Boot DT part.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

With multiple environments, the 'get_char' callback for env
drivers does not really make sense any more because it is
only supported by two drivers (eeprom and nvram).

To restore single character loading for these drivers,
override 'env_get_char_spec'.
Signed-off-by: NSimon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>

Commit 7d714a24 ("env: Support multiple environments") added
static variable env_load_location. When saving environmental
variables, this variable is presumed to have the value set before.
In case the value was set before relocation and U-Boot runs from a
NOR flash, this variable wasn't writable. This causes failure when
saving the environment. To save this location, global data must be
used instead.
Signed-off-by: NYork Sun <york.sun@nxp.com>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>

This makes the shell so much more pleasant to use, so enable it.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Due to size limitations of the MERAM, switch U-Boot to SPL.
The SPL is loaded by the SPI_LOADER into MERAM and then loads
U-Boot proper into DRAM. This way U-Boot can freely grow in
size in DRAM, as there is plenty of it.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: To update U-Boot, first install u-boot.img to 0x140000 in SPI NOR,
      then use the Minimon to flash u-boot-spl.srec using ls,2,e6304000.
      To generate u-boot-spl.srec, use objcopy:
        arm-linux-gnueabi-objcopy -O srec spl/u-boot-spl u-boot-spl.srec

Those two nodes are needed to configure pinmux before relocation
and to configure clock before relocation, since CPG/MSSR needs
access to RST node. This is not noticable on Gen3, but on Gen2
this causes problems in SPL if they are not available early.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Make the SCIF available before relocation and in SPL on R8A7791 Porter.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Cosmetic change, replace CONFIG_* with CONFIG_IS_ENABLED(*) .
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

This makes the shell so much more pleasant to use, so enable it.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Enable support for applying DT overlays on Gen3. This is convenient
for handling extra additional hardware, like ie. the Kingfisher.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Reset and initialize the PHY once in the probe() function rather than
doing it over and over again is start() function. This requires us to
keep the clock enabled while the driver is in use. This significantly
reduces the time between transfers as the PHY doesn't have to restart
autonegotiation between transfers, which takes forever.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Joe Hershberger <joe.hershberger@ni.com>

The SD driver calls clk_set_rate() before clk_enable(), yet clk_set_rate()
implementation in the clock driver does not set the SD-IF divider. Fix it.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>