- 01 4月, 2018 4 次提交
-
-
由 Masahiro Yamada 提交于
fdt_region.c does not depend on anything in libfdt_internal.h Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Masahiro Yamada 提交于
This macro is locally referenced in common/image-fdt.c Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Mario Six 提交于
Commit 286ede65 ("drivers: core: Add translation in live tree case") made dev_get_addr always use proper bus translations for addresses read from the device tree. But this leads to problems with certain busses, e.g. I2C busses, which run into an error during translation, and hence stop working. It turns out that of_translate_address() and fdt_translate_address() stop the address translation with an error when they're asked to translate addresses for busses where #size-cells == 0 (comment from drivers/core/of_addr.c): * Note: We consider that crossing any level with #size-cells == 0 to mean * that translation is impossible (that is we are not dealing with a value * that can be mapped to a cpu physical address). This is not really specified * that way, but this is traditionally the way IBM at least do things To fix this case, we check in both the live-tree and non-live tree-case, whether the bus of the device whose address is about to be translated has size-cell size zero. If this is the case, we just read the address as a plain integer and return it, and only apply bus translations if the size-cell size if greater than zero. Signed-off-by: NMario Six <mario.six@gdsys.cc> Signed-off-by: NMartin Fuzzey <mfuzzey@parkeon.com> Reported-by: NMartin Fuzzey <mfuzzey@parkeon.com> Fixes: 286ede65 ("drivers: core: Add translation in live tree case") Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Andy Yan 提交于
dm_scan_fdt_node can't work when live dt is active, we should use dm_scan_fdt_live instead. Signed-off-by: NAndy Yan <andy.yan@rock-chips.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
- 31 3月, 2018 4 次提交
-
-
由 Andre Heider 提交于
The value at the end of the rom is not a pointer, it is an offset relative to the end of rom. Signed-off-by: NAndre Heider <a.heider@gmail.com>
-
由 Andre Heider 提交于
The cast breaks the pointer on 64bit archs, so lets get rid of it. Signed-off-by: NAndre Heider <a.heider@gmail.com> Reviewed-by: NAlexander Graf <agraf@suse.de>
-
由 Kever Yang 提交于
Use live dt interface for pinctrl_select_state_full() Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Kever Yang 提交于
Add api for who can not get phandle from a device property. Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
- 26 3月, 2018 4 次提交
-
-
-
-
-
git://git.denx.de/u-boot-microblaze由 Tom Rini 提交于
Xilinx changes for v2018.05 - Fix mkimage recognition - Update all my fragments ZynqMP: - Use clk driver - Support loading elfs in el1 - Various DTS and defconfig changes - Enable newer pmufw versions - Support more clocks - Remove ep108 - Secure image support - Fix memtest setup Zynq: - Enabling watchdog driver - Support more clocks - defconfig changes fpga: - Simplify error path net: - GMII case update
-
- 24 3月, 2018 4 次提交
-
-
由 Petr Vorel 提交于
Signed-off-by: NPetr Vorel <petr.vorel@gmail.com>
-
由 Petr Vorel 提交于
Introduce another difference from upstream (kernel) source in fs/ubifs/super.c: adding preprocessor condition as y variable in mount_ubifs() depends on CONFIG_UBIFS_SILENCE_MSG: fs/ubifs/super.c:1337:15: error: variable ?y? set but not used [-Werror=unused-but-set-variable] long long x, y; Not setting CONFIG_UBIFS_SILENCE_MSG in am335x_igep003x_defconfig and igep0032_defconfig. Although it was defined in their config headers, it depends on CMD_UBIFS which is not set for them. Signed-off-by: NPetr Vorel <petr.vorel@gmail.com> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Heiko Schocher <hs@denx.de>
-
由 Petr Vorel 提交于
Use of CONFIG_UBIFS_SILENCE_MSG was added in 147162da ("ubi: ubifs: Turn off verbose prints") Then it was removed in ff94bc40 ("mtd, ubi, ubifs: resync with Linux-3.14") Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Heiko Schocher <hs@denx.de> Signed-off-by: NPetr Vorel <petr.vorel@gmail.com>
-
由 Sjoerd Simons 提交于
The ti,pindir-d0-out-d1-in property is not expected to have a value according to the device-tree binding, so treat it as a boolean not a uint property. Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk> Reviewed-by: NJagan Teki <jagan@openedev.com>
-
- 23 3月, 2018 24 次提交
-
-
git://git.denx.de/u-boot-arc由 Tom Rini 提交于
Alexey: 1. Significantly rework cache-related functionality. In particular that fixes coherency problems in some corner-cases, allows us to enable and disable caches in run-time and still have properly running system, finally support execution from real flash (before we used to run from DDR from the very beginning). 2. Remove string routines implemented in assembly. That allows us to build and run U-Boot on wide range of ARC cores with different configurations. I.e. whatever tuning is used on GCC's command-line we'll get code for desired flavor of ARC. Otherwise for each and every corner-case we would need to add ifdefs in assembly code to accommodate missing instructions etc. 3. Get use of GCC's garbage collector which helps to slim-down resulting image quite a bit. 4. Also now we may disable U-Boot self-relocation for ARC if needed either by platform or for debugging purposes.
-
由 Eugeniy Paltsev 提交于
Refactor GO and PREP subcommands implementation for a simpler override in the boards platform code. Signed-off-by: NEugeniy Paltsev <Eugeniy.Paltsev@synopsys.com> Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
-
由 Michal Simek 提交于
Fix my fragments to list all files in the repo. Also fix path to for Xilinx Zynq SoC (mach-zynq) It should be the part of "ARM: zynq: move SoC sources to mach-zynq" (sha1: 0107f240) And cover dts files in board MAINTAINERS files. Reported-by: NHeinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
There is an issue to recognize zynq or zynqmp image because header checking is just the same. That's why zynqmp images are recognized as zynq one. Check unused fields which are initialized to zero in zynq format (__reserved1 0x38 and __reserved2 0x44) which are initialized for zynqmp. This should ensure that images are properly recognized by: ./tools/mkimage -l spl/boot.bin Also show image type as ZynqMP instead of Zynq which is confusing. Reported-by: NAlexander Graf <agraf@suse.de> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Tested-by: NAlexander Graf <agraf@suse.de>
-
This patch adds new command "zynqmp" to handle zynqmp specific commands like "zynqmp secure". This secure command is used for verifying zynqmp specific secure images. The secure image can either be authenticated or encrypted or both encrypted and authenticated. The secure image is prepared using bootgen and will be in xilinx specific BOOT.BIN format. The optional key can be used for decryption of encrypted image if user key was specified while creation BOOT.BIN. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
ZynqMP Emulation board is no longer tested and there is no reason to keep maintaining it. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
The vcu disable bit in efuse ipdisable register is valid only if PL powered up so, consider PL powerup status for determing EG/EV part. If PL is not powered up, ignore EG/EV part of string. The PL powerup status will be filled by pmufw based on PL PROGB status in the 9th bit of version field. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Vipul Kumar 提交于
This patch print pl clocks (pl0...pl3) and watchdog clock using clk dump. Signed-off-by: NVipul Kumar <vipulk@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Vipul Kumar 提交于
NAND erase was not happening for size 1GiB or more. Erase command was executing successfully but in actual, it was not erasing. This patch fixed erase issue for 1 GiB or more size nand. Signed-off-by: NVipul Kumar <vipulk@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Use appended dtb which is default option for zynq boards. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
The same command should be used for x16 configuration. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Vipul Kumar 提交于
This patch changed CONFIG_SYS_MEMTEST_SCRATCH address to the accessible DDR address used by alternate memory test. Before this, 0xfffc0000 address was used, which is the OCM address and not enabled in MMU table. So, whenever trying to access 0xfffc0000 address, got Synchronous Abort exception. After changing CONFIG_SYS_MEMTEST_SCRATCH address, alternate memory test is working fine. Signed-off-by: NVipul Kumar <vipulk@xilinx.com> Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Enable watchdog with reset-on-timeout feature. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Watchdog is only enabled in full u-boot. Adoption for SPL should be also done because that's the right place where watchdog should be enabled. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Shreenidhi Shedi 提交于
This IP can be found on Zynq and ZynqMP devices. The driver was tested with reset-on-timeout; feature. Also adding WATCHDOG symbol to Kconfig because it is required. Signed-off-by: NShreenidhi Shedi <imshedi@gmail.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
watchdog clock is also connected to cpu 1X clocksource. Zynq> clk dump ... Before: swdt 4294967290 After: swdt 111111110 Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
As of now newer pmufw is keeping old interfaces. That's why permit u-boot to run on newer version. Recommended version will be setup later. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
This patch bypasses phy detection logic for GMII interface and just depend on phy address received from DT. This patch is required as phy detection logic is different for some phys like xilinx phy which can be connected over SGMII and GMII interface. This fixes the issue of ethernet failures when xilinx phy is connected over GMII interface. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Nitin Jain 提交于
This patch is adding support to switch to EL1 while loading an EL1 application with u-boot running at EL above EL1 in aarch64 mode. Signed-off-by: NNitin Jain <nitinj@xilinx.com> Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
It helps with debugging. Signed-off-by: NSiva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Enable missing driver on this board. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Check !desc earlier to simplify code. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Acked-by: NSimon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com> Reviewed-by: NSimon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
-
由 Michal Simek 提交于
Make defconfigs up2date with current location. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Use zynqmp clock driver instead of fixed clocks. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-