This change adds some basic summary information to the MAKEALL script.
The summary information includes how many boards were compiled, how many
boards had compile warnings or errors, and which specific boards had
compile warnings or errors.

This information is useful when doing compile testing to quickly
determine which boards are broken.

As a side benefit, no empty $BOARD.ERR files are generated by MAKEALL.
Previously, each board had a corresponding $BOARD.ERR file, even if the
board compiled cleanly.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>

Users should use microblaze-generic platform.
This platform is longer not supported.
Signed-off-by: NMichal Simek <monstr@monstr.eu>

Signed-off-by: NDirk Eibach <eibach@gdsys.de>
Signed-off-by: NStefan Roese <sr@denx.de>

This patch adds support for the DevKit8000 board.
Signed-off-by: NFrederik Kriewitz <frederik@kriewitz.eu>

The CM-BF537U is similar to the CM-BF537E module, but enough to need its
own board port.
Signed-off-by: NHarald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The Calao TNY-A9260 and TNY-9G20 are boards manufactured and sold by
Calao Systems <http://www.calao-systems.com>. Their components are very
similar to the AT91SAM9260EK board, so their configuration is based on
the configuration of this board. There are however some differences:
different clocks, no LCD, no ethernet. They also can use SPI EEPROM to
store the environment.
Signed-off-by: NAlbin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The Calao SBC35-A9G20 board is manufactured and sold by Calao Systems
<http://www.calao-systems.com>. It is built around an AT91SAM9G20 ARM SoC
running at 400MHz. It features an Ethernet port, an SPI RTC backed by an onboard
battery , an SD/MMC slot, a CompactFlash slot, 64Mo of SDRAM, 256Mo of NAND
flash, two USB host ports, and an USB device port. More informations can be
found at <http://www.calao-systems.com/articles.php?lng=en&pg=5936>
Signed-off-by: NAlbin Tonnerre <albin.tonnerre@free-electrons.com>

This patch adds support for i.MX27-LITEKIT development board from
LogicPD. This board uses i.MX27 SoC and has 2MB NOR flash, 64MB NAND
flash, FEC ethernet controller integrated into i.MX27.
Signed-off-by: NIlya Yanok <yanok@emcraft.com>
Acked-by: NWolfgang Denk <wd@denx.de>

P1011 and P2010 are single core variants of P1010 and P2020 respectively.
The board(RDB) will be same.
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The code base adds P1 & P2 RDB platforms support.
The folder and file names can cater to future SOCs of P1/P2 family.
P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series.

Tested following on P2020RDB:
1. eTSECs
2. DDR, NAND, NOR, I2C.
Signed-off-by: NPoonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Add support for the DEKA Research and Development galaxy5200 board

The galaxy5200 is an Freescale mpc5200 based embedded industrial
control board.
Signed-off-by: NEric Millbrandt <emillbrandt@dekaresearch.com>

Board support for the Guntermann & Drunck CompactCenter and
DevCon-Center.
Based on the AMCC Canyonlands board support by Stefan Roese.
Signed-off-by: NDirk Eibach <eibach@gdsys.de>
Signed-off-by: NStefan Roese <sr@denx.de>

This patch adds support for the esd VME8349 board equipped with the
MPC8349. It's a VME PMC carrier board equipped with the Tundra
TSI148 VME-bridge.
Signed-off-by: NReinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>

Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: NStefan Roese <sr@denx.de>

The XPedite1000 is an X-ES product thus it can be put in board/xes along
with other X-ES boards.  Along with the move, the board was renamed to
XPedite1000 from XPedite1K to fit X-ES's standard naming convention.
Maintainership was also transfered to Peter Tyser.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Signed-off-by: NStefan Roese <sr@denx.de>

Board support for the Guntermann & Drunck DL-Vision.
Signed-off-by: NDirk Eibach <eibach@gdsys.de>
Signed-off-by: NStefan Roese <sr@denx.de>

This is Marvell's 88F6281_A0 based reference design board

This patch is tested for-
1. Boot from DRAM/NAND flash/NFS
2. File transfer using tftp and loadb
3. NAND flash read/write/erase
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

This is Marvell's 88F6281_A0 based custom board developed
for wireless access point product

This patch is tested for-
1. Boot from DRAM/SPI flash/NFS
2. File transfer using tftp and loadb
3. SPI flash read/write/erase
4. Booting Linux kernel and RFS from SPI flash
5. Boot from USB supported
Reviewed-by: NRonen Shitrit <rshitrit@marvell.com>
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>

Reference:
http://plugcomputer.org/
http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support

This patch is tested for-
1. Boot from DRAM/NAND flash
2. File transfer using tftp
3. NAND flash read/write/erase
4. Linux kernel and RFS Boot from NAND
5. Enabled USB PHY init for kernel need
6. Boot from USB supported

Note: to boot Kirkwood kernel with USB support,
	you should add "usb start" in the boot sequence
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>

Signed-off-by: NTsiChung Liew <tsicliew@gmail.com>

AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>

AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>

ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.

More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.htmlSigned-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>

Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: NJon Smirl <jonsmirl@gmail.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>

The Polaris board is based on the TrizepsIV module of
Keith & Koep (http://www.keith-koep.com).
Signed-off-by: NStefano Babic <sbabic@denx.de>

This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: NDaniel Gorsulowski <Daniel.Gorsulowski@esd.eu>

Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).

This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>
Acked-by: NFabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Initial support for Extreme Engineering Solutions XPedite5170 -
a MPC8640-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: NPeter Tyser <ptyser@xes-inc.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

The PM9261 board is based on the AT91SAM9261-EK board.

Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.htmlSigned-off-by: NIlko Iliev <iliev@ronetix.at>
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NHoan Hoang <hnhoan@i-syst.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>