The Keymile SUPx5 board series is based on a PBEC8321 but
contains an additional PBUS FPGA (LPXF) on local bus CS2.
Signed-off-by: NThomas Reufer <thomas.reufer@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>

First step for a cleanup of all header files for km8321 boards.
Signed-off-by: NThomas Reufer <thomas.reufer@keymile.com>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>

The mgcoge2 board from keymile deploys two different processors.
An ARM based Kirkwood for the "unit" part of the SW and a PPC for
the "ne" part of the SW. Therefore in Linux and U-Boot the names
for the board are mgcoge2un and mgcoge2ne. This patch adds the
mgcoge2ne part of the board. The ppc part of mgboge2 is quite
similar to mgcoge, therefore a generic header km82xx-common.h
was introduced to collect all similiarities. Currently the only
difference is that mgcoge2ne has a 64 MB numonyx NOR flash with
a single die. The mgcoge has a dual die flash 2*32MB from spansion.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

The Kirwood based SUEN8 board from Keymile is at this stage
the same than the suen3 board. This patch adds the board
support for the suen8.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

This board is similar to keymile suen3.
Signed-off-by: NClive Stubbings <clive.stubbings@xentech.co.uk>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>

This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: NLukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

This board is similar to suvd3 board. So most initialisation topics
are taken from suvd3 (UART1, Ethernet, piggy PHY, flash, ram) only the
application specific chip selects differ.
Signed-off-by: NLukas Roggli <lukas.roggli@keymile.com>
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

- serial console on UART1
- Ethernet RMII over UCC4
- PHY SMSC LAN8700
- 64MB Flash
- 128 MB DDR2 RAM
- I2C
- bootcount

This board is similiar to the kmeter1 (8360) board,
so common config options are extracted into the
include/configs/km83xx-common.h file.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

This patch reworks all headerfiles for keymile boards. Furthermore
the environment variables are refactored.

Changes:
  - introduce km-powerpc.h file and extract ppc specific parts to it
  - move ARM specific options and vaiables to km_arm.h
  - sort the environment variables to logical groups
  - enhance the description of the environment variables
  - remove KM specific HW key and board id from kernel command line
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

- adapt copyright string
- change bootdelay to 2 seconds
- set max number of command args to 32
- set I/O buffer size to 512
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

- use I/O accessors
  -> For accessing the FPGA therefore a struct km_bec_fpga
     is introduced.
- no longer externs needed
- to defines, that only select functions, don;t assign a
  numeric value
- Codingstyle changes to prevent checkpatch errors/warnings
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>

The MACH_TYPE SUEN3 is now to specific for keymile boards, because
other boards similar to suen3 will follow. So the MACH_SUEN3 was renamed
to MACH_KM_KIRKWOOD.
Signed-off-by: NHolger Brunck <holger.brunck@keymile.com>
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>

add following functions to common.h, to prevent
extern declarations:

void disable_addr_trans(void);
void enable_addr_trans(void);
void ddr_enable_ecc(unsigned int dram_size);
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NKim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>

Signed-off-by: NThomas Chou <thomas@wytron.com.tw>

For freescale i.MX53 eSDHCv2, when using CMD12, cmdtype need
to be set to ABORT, otherwise, next read command will hang.

This is a software Software Restrictions in i.MX53 reference manual:

29.7.8 Multi-block Read
For pre-defined multi-block read operation, that is,the number of blocks
to read has been defined by previous CMD23 for MMC, or pre-defined number
of blocks in CMD53 for SDIO/SDCombo,or whatever multi-block read without
abort command at card side, an abort command, either automatic or manual
CMD12/CMD52, is still required by ESDHC after the pre-defined number of
blocks are done, to drive the internal state machine to idle mode. In this
case, the card may not respond to this extra abort command and ESDHC will
get Response Timeout.  It is recommended to manually send an abort command
with RSPTYP[1:0] both bits cleared.
Signed-off-by: NJason Liu <jason.hui@linaro.org>

Signed-off-by: NJohn Rigby <john.rigby@linaro.org>

Make existing field b_max field in struct mmc unconditional
and use it instead of CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_bread
and mmc_bwrite.

Initialize b_max to CONFIG_SYS_MMC_MAX_BLK_COUNT in mmc_register
if it has not been initialized by the hw driver.

Initialize b_max to 0 in all callers to mmc_register.
Signed-off-by: NJohn Rigby <john.rigby@linaro.org>
Signed-off-by: NAndy Fleming <afleming@freescale.com>

As Andy Fleming suggested, we can call mmc_init() in mmc_spi command.
So that we don't need to run mmcinfo command next.
Signed-off-by: NThomas Chou <thomas@wytron.com.tw>

Added the board specific definitions to use the MMCI device.
Signed-off-by: NMatt Waddel <matt.waddel@linaro.org>

Add support for the ARM PrimeCell MultiMedia Interface - PL180.
Ported from original device driver written by ST-Ericsson.
Signed-off-by: NMatt Waddel <matt.waddel@linaro.org>

Use the 'video-mode' environment variable (for Freescale chips that have a
DIU display controller) to designate the full video configuration.  Previously,
the DIU driver used the 'monitor' variable, and it was used only to determine
the output video port.

The old definition of the "monitor" environment variable only determines
which video port to use for output.  This variable was set to a number (0,
1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port.  The
resolution was hard-coded into board-specific code.  The Linux command-line
arguments needed to be hard-coded to the proper video definition string.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>

Add function video_get_video_mode(), which parses the "video-mode" environment
variable and returns each of its components.  The format matches the video=
command-line option used for Linux:

	video-mode=<driver>:<xres>x<yres>-<depth>@<freq><,option=string>

	<driver> The video driver, ignored by U-Boot
	<xres> The X resolution (in pixels) to use.
	<yres> The Y resolution (in pixels) to use.
	<depth> The color depth (in bits) to use.
	<freq> The frequency (in Hz) to use.
	<options> A comma-separated list of device-specific options
Signed-off-by: NTimur Tabi <timur@freescale.com>

There seems to be tools producing incorrect 'end of bitmap data'
markers '0100' in a RLE bitmap. Drawing such bitmaps can result
in overwriting memory above the frame buffer. E.g. on MPC5121e
based boards this memory can contain U-Boot environment.

We may not rely on the correct end of bitmap data marker 0001
only, but also have to check whether we are going to draw a
valid frame buffer scan line.

The patch provides a fix by maintaining a pixel counter
which is incremented by the amount of pixels we are going
to draw. If the counter exceeds frame buffer pixels limit
we stop the drawing with the error message.
Reported-by: NMichael Weiss <michael.weiss@ifm.com>
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Tested-by: NAnatolij Gustschin <agust@denx.de>

The following boards gain device tree support with this patch:

ca9x4_ct_vxp - Versatile Express

i.mx5 boards:
efikamx
mx51evk
mx53evk

OMAP boards:
devkit8000
igep0020
igep0030
omap3_overo
omap3_pandora
omap4_sdp3430
omap3_zoom1
omap3_zoom2
omap4_panda
omap4_sdp4430

Tegra boards:
Harmony
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

Deblock i2c bus when switching to another i2c bus, if using
i2c_set_bus_num().
Signed-off-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>

To make sure that the mux can be configured a deblocking sequence
is done before the mux configuration. After the mux switch the new leaf
of, the i2c tree must be again deblocked.
Signed-off-by: NStefan Bigler <stefan.bigler@keymile.com>
Acked-by: NHeiko Schocher <hs@denx.de>
cc: Wolfgang Denk <wd@denx.de>
cc: Detlev Zundel <dzu@denx.de>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: NValentin Longchamp <valentin.longchamp@keymile.com>

Signed-off-by: NPo-Yu Chuang <ratbert@faraday-tech.com>

u-boot environments, esp. when boards are shared across multiple
users, can get pretty large and time consuming to visually parse.
The grepenv command this patch adds can be used in lieu of printenv
to facilitate searching.  grepenv works like printenv but limits
its output only to environment strings (variable name and value
pairs) that match the user specified substring.

the following examples are on a board with a 5313 byte environment
that spans multiple screen pages:

Example 1:  summarize ethernet configuration:

=> grepenv eth TSEC
etact=FM1@DTSEC2
eth=FM1@DTSEC4
ethact=FM1@DTSEC2
eth1addr=00:E0:0C:00:8b:01
eth2addr=00:E0:0C:00:8b:02
eth3addr=00:E0:0C:00:8b:03
eth4addr=00:E0:0C:00:8b:04
eth5addr=00:E0:0C:00:8b:05
eth6addr=00:E0:0C:00:8b:06
eth7addr=00:E0:0C:00:8b:07
eth8addr=00:E0:0C:00:8b:08
eth9addr=00:E0:0C:00:8b:09
ethaddr=00:E0:0C:00:8b:00
netdev=eth0
uprcw=setenv ethact $eth;setenv filename p4080ds/R_PPSXX_0xe/rcw_0xe_2sgmii_rev2_high.bin;setenv start 0xe8000000;protect off all;run upimage;protect on all
upuboot=setenv ethact $eth;setenv filename u-boot.bin;setenv start eff80000;protect off all;run upimage;protect on all
upucode=setenv ethact $eth;setenv filename fsl_fman_ucode_P4080_101_6.bin;setenv start 0xef000000;protect off all;run upimage;protect on all
usdboot=setenv ethact $eth;tftp 1000000 $dir/$bootfile;tftp 2000000 $dir/initramfs.cpio.gz.uboot;tftp c00000 $dir/p4080ds-usdpaa.dtb;setenv bootargs root=/dev/ram rw console=ttyS0,115200 $othbootargs;bootm 1000000 2000000 c00000;
=>

Example 2: detect unused env vars:

=> grepenv etact
etact=FM1@DTSEC2
=>

Example 3: reveal hardcoded variables; e.g., for fdtaddr:

=> grepenv fdtaddr
fdtaddr=c00000
nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr
ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;tftp $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr
=> grep $fdtaddr
fdtaddr=c00000
my_boot=bootm 0x40000000 0x41000000 0x00c00000
my_dtb=tftp 0x00c00000 $prefix/p4080ds.dtb
nohvboot=tftp 1000000 $dir/$bootfile;tftp 2000000 $dir/$ramdiskfile;tftp c00000 $dir/$fdtfile;setenv bootargs root=/dev/ram rw ramdisk_size=0x10000000 console=ttyS0,115200;bootm 1000000 2000000 c00000;
=>

This patch also enables the grepenv command by default on
corenet_ds based boards (and repositions the DHCP command
entry to keep the list sorted).
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>

Signed-off-by: NTimur Tabi <timur@freescale.com>

commit 560d424b "env: re-add
support for auto-completion" fell short of its description -
the 'used' logic in hmatch_r was reversed - 'used' is 0 if
the hash table entry is not used, or -1 if deleted.  This
patch makes hmatch_r actually match on valid ('used') entries,
instead of skipping them and failing to match anything.

typing 'printenv tft' and hitting 'tab' now displays valid
choices for variable names.
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Tested-by: NMike Frysinger <vapier@gentoo.org>

call flash_protect_default() to protect default sectors.
Signed-off-by: NHeiko Schocher <hs@denx.de>

- rev5 board has phy addr 1 -> adapt CONFIG_PHY_ADDR define
  in board config file.
- also fixup the phy addr entry in dts, before booting
  Linux.
Signed-off-by: NHeiko Schocher <hs@denx.de>
Acked-by: NDetlev Zundel <dzu@denx.de>

If neither CONFIG_CMD_PING or CONFIG_CMD_SNTP are defined but
CONFIG_CMD_DNS is, a compile-time error will occur due to the
absence of a goto label.
Signed-off-by: NGray Remlin <gryrmln@gmail.com>

This patch fixes problems in the handling of redundant environment in env_sf.c

The major problem are double calls of free() on the allocated buffers,
which damages the internal data of malloc and crashes on next call.

In addition, the selection of the active environment had errors and compiler
warnings, which are corrected by this patch.
Signed-off-by: NThomas Langer <thomas.langer@lantiq.com>