- 12 1月, 2008 3 次提交
-
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Heiko Schocher 提交于
Signed-off-by: NHeiko Schocher <hs@denx.de>
-
由 Guennadi Liakhovetski 提交于
The TK885D board uses a TQM885D module from TQ, this port adds an own configuration file and adds a last_stage_init() method to configure the two PHYs, depending on the phy_auto_nego environment variable. Signed-off-by: NGuennadi Liakhovetski <lg@denx.de>
-
- 11 1月, 2008 1 次提交
-
-
由 Anton Vorontsov 提交于
This is MPC8360E based board with: - 256MB fixed SDRAM; - 8MB Intel Strata NOR flash; - StMICRO 64MiB NAND flash; - two 10/100/1000 ethernet ports connected via Broadcom BCM5481 PHYs; - two 10/100 ethernet ports connected via National DP83848 PHYs; - one PCI and one miniPCI slots; - four serial ports (two NS16550-compatible, two UCCs); - four USB ports working through MPC8360E "FHCI" USB controller; - Fujitsu MB86277 graphics controller; - Analog to Digital Converter/Touchscreen controller, AD7843 connected to SPI. Features not supported in this patch are: - StMICRO 64MiB NAND flash (patch sent); - MINT framebuffer initialization (patch is pending); - Fetching production information from the EEPROM via I2C; - FHCI USB; - Two slow UCCs used as RS-485 UARTs. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 10 1月, 2008 2 次提交
-
-
由 robert lazarski 提交于
Add support for Instituto Atlantico's ATUM8548 board Signed-off-by: Nrobert lazarski <robertlazarski@gmail.com>
-
由 Joe Hamman 提交于
Add support for Wind River's SBC8548 reference board. Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com> Signed-off by: Andy Fleming <afleming@freescale.com>
-
- 08 1月, 2008 1 次提交
-
-
由 Dave Liu 提交于
Add the MAINTAINER and MAKEALL entries for mpc837xemds Signed-off-by: NDave Liu <daveliu@freescale.com>
-
- 29 12月, 2007 1 次提交
-
-
由 Matthias Fuchs 提交于
This patch brings the PMC440 board configuration file. Finally it enables the PMC440 board support. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>
-
- 28 12月, 2007 2 次提交
-
-
由 Matthias Fuchs 提交于
This board never left prototyping state and it became a millstone round my neck. So remove it. Signed-off-by: NMatthias Fuchs <matthias.fuchs@esd-electronics.com>
-
由 Larry Johnson 提交于
These patches add support for the PPC440EPx-based "Korat" board to U-Boot. They are based primarily on support for the Sequoia board. Signed-off-by: NLarry Johnson <lrj@acm.org>
-
- 17 12月, 2007 2 次提交
-
-
由 Haavard Skinnemoen 提交于
ATSTK1004 is a daughterboard for ATSTK1000 with the AT32AP7002 CPU, which is a derivative of AT32AP7000. Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
-
由 Haavard Skinnemoen 提交于
ATSTK1003 is a daughterboard for ATSTK1000 with the AT32AP7001 CPU, which is a derivative of AT32AP7000. Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
-
- 29 11月, 2007 2 次提交
-
-
由 Nobuhiro Iwamatsu 提交于
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
- 27 11月, 2007 1 次提交
-
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 17 11月, 2007 1 次提交
-
-
由 Shinya Kuribayashi 提交于
Signed-off-by: NShinya Kuribayashi <skuribay@ruby.dti.ne.jp>
-
- 09 11月, 2007 1 次提交
-
-
由 Peter Pearse 提交于
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
-
- 03 11月, 2007 1 次提交
-
-
由 Stefan Roese 提交于
This patch adds NAND booting support for the AMCC 405EX(r) eval boards. Again, only one image supports both targets. Signed-off-by: NStefan Roese <sr@denx.de>
-
- 01 11月, 2007 3 次提交
-
-
由 Stefan Roese 提交于
The Haleakala is nearly identical with the Kilauea eval board. The only difference is that the 405EXr only supports one EMAC and one PCIe interface. This patch adds support for the Haleakala board by using the identical image for Kilauea and Haleakala. The distinction is done by comparing the PVR. Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
- 18 10月, 2007 2 次提交
-
-
由 Tony Li 提交于
Add MPC8360EMDS_ATM_config and MPC832XEMDS_ATM_config into Makfile and MAKEALL Signed-off-by: NTony Li <tony.li@freescale.com> Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Jon Loeliger 提交于
Signed-off-by: NEd Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: NMahesh Jade <mahesh.jade@freescale.com> Signed-off-by: NJason Jin <Jason.jin@freescale.com> Signed-off-by: NJon Loeliger <jdl@freescale.com>
-
- 07 9月, 2007 1 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 18 8月, 2007 1 次提交
-
-
由 TsiChungLiew 提交于
Signed-off-by: NTsiChungLiew <Tsi-Chung.Liew@freescale.com>
-
- 17 8月, 2007 2 次提交
-
-
由 TsiChungLiew 提交于
Signed-off-by: NTsiChungLiew <Tsi-Chung.Liew@freescale.com>
-
由 TsiChungLiew 提交于
Signed-off-by: NTsiChungLiew <Tsi-Chung.Liew@freescale.com>
-
- 16 8月, 2007 3 次提交
-
-
由 Andy Fleming 提交于
Changes to the TSEC driver affect almost all 83xx, 85xx, and 86xx boards. Now we can do a MAKEALL test on all of them! Signed-off-by: NAndy Fleming <afleming@freescale.com>
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Kim Phillips 提交于
and reorder the existing 83xx maintainers alpha. Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
- 14 8月, 2007 1 次提交
-
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
- 11 8月, 2007 3 次提交
-
-
由 Kim Phillips 提交于
..by placing board entries one per line, as suggested by jdl. Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Joe Hamman 提交于
Add support for Wind River's SBC8641D reference board. Signed-off by: Joe Hamman <joe.hamman@embeddedspecialties.com> Acked-by: NWolfgang Denk <wd@denx.de> Acked-by: NJon Loeliger <jdl@freescale.com>
-
由 Sergey Kubushyn 提交于
Add support for the following DaVinci boards: - DV_EVM - SCHMOOGIE - SONATA Changes: - Split into separate board directories - Removed changes to MTD_DEBUG (or whatever it's called) - New CONFIG_CMD party line followed - Some cosmetic fixes, cleanup etc. - Patches against the latest U-Boot tree as of now. - Fixed CONFIG_CMD_NET in net files. - Fixed CONFIG_CMD_EEPROM for schmoogie. - Made sure it compiles and works (forceenv() link problem) on SCHMOOGIE and DV_EVM. Can't check if it works on SONATA, don't have a board any more, but it at least compiles. Here is an excerpt from session log on SCHMOOGIE... U-Boot 1.2.0-g6c33c785-dirty (Aug 7 2007 - 13:07:17) DRAM: 128 MB NAND: 128 MiB In: serial Out: serial Err: serial ARM Clock : 297MHz DDR Clock : 162MHz ETH PHY : DP83848 @ 0x01 U-Boot > iprobe Valid chip addresses: 1B 38 3A 3D 3F 50 5D 6F U-Boot > ping 192.168.253.10 host 192.168.253.10 is alive U-Boot > Signed-off-by: NSergey Kubushyn <ksi@koi8.net> Acked-by: NDirk Behme <dirk.behme@gmail.com> Acked-by: NZach Sadecki <Zach.Sadecki@ripcode.com> Acked-by: NStefan Roese <sr@denx.de>
-
- 10 8月, 2007 2 次提交
-
-
由 Stefan Roese 提交于
Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Niklaus Giger 提交于
This series of patches adds support for 2 boards from Netstal Maschinen. The HCU4 has a PPC405Gpr and the HCU5 has a PPC440EPX. The HCU4 has a somehow complicated flash setup, as the booteprom is only 8 bits and the CFI 16 bits wide, which makes it impossible to use a more elegant solution. The HCU5 has only a booteprom as the whole code will be downloaded from a different board which has HD, CD-ROM, etc and where all code is stored. This is my third try. I incorporated all suggestions made by Wolfgang and Stefan. Thanks them a lot. Signed-off-by: NNiklaus Giger <niklaus.giger@netstal.com>
-
- 03 8月, 2007 1 次提交
-
-
由 Bartlomiej Sieka 提交于
Add the ability for modules from the Schindler cm5200 family to use a single U-Boot image: - rename cm1_qp1 to cm5200 - add run-time module detection - parametrize SDRAM configuration according to the module we are running on Few minor, board-specific fixes included in this patch: - better MAC address handling - updated default environment ('update' command uses +{filesize} now) - improved error messages in the auto-update code - allow booting U-Boot from RAM (CFG_RAMBOOT) Signed-off-by: NGrzegorz Bernacki <gjb@semihalf.com> Signed-off-by: NPiotr Kruszynski <ppk@semihalf.com> Signed-off-by: NBartlomiej Sieka <tur@semihalf.com>
-
- 02 8月, 2007 1 次提交
-
-
由 Wolfgang Denk 提交于
Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 27 7月, 2007 1 次提交
-
-
由 Rafal Jaworowski 提交于
The following MPC5121e subsystems are supported: - low-level CPU init - NOR Boot Flash (common CFI driver) - DDR SDRAM - FEC - I2C - Watchdog Signed-off-by: NGrzegorz Bernacki <gjb@semihalf.com> Signed-off-by: NRafal Jaworowski <raj@semihalf.com> Signed-off-by: NJan Wrobel <wrr@semihalf.com>
-
- 26 7月, 2007 1 次提交
-
-
由 John Otken 提交于
Signed-off-by: NJohn Otken <john@softadvances.com>
-