This patch contains the generic changes required after
change to generic API in the previous patch.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Convert all OMAP specific functions to use the common API
definitions in include/asm/gpio.h. In the process, made
few additional changes:
 - Use -EINVAL consistently. -1 was used in many places.
 - Removed one-liner static functions that were used only
   once. Replaced the content as necessary.
 - Combines implementation of functions omap_get_gpio_dataout()
   and omap_get_gpio_datain(). To do so, new static function
   _get_gpio_direction() was added.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

This patch removes a hardcoded MAC address
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Modify the MEMTEST start and end address. The memtest range was overlapping the
CONFIG_SYS_LOAD_ADDR which causes the uImage to be corrupt.Also, modify the
size for which mtest is run to 32MB from 16MB.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NNagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Enable SPI flash boot mode in configuration file as default.
With the introduction of 456MHz part, SPI operating frequency
will increase and at this frequency SPI does not work correctly.
Hence reduce the default SPI speed to 30MHz from 50MHz.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NNagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Modify U-boot promt string from 'DA830-evm >' to 'U-Boot >' as
there are many variants of da830 based boards which have diffrent
names such as L137, AM1707 etc.
Signed-off-by: NSudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: NNagabhushana Netagunte <nagabhushana.netagunte@ti.com>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

OMAP3: Add 37xx ESx revision numbers.
Signed-off-by: NMichael Jones <michael.jones@matrix-vision.de>
Signed-off-by: NHoward D. Gray <howard.gray@matrix-vision.de>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Signed-off-by: NMichael Jones <michael.jones@matrix-vision.de>
Acked-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

This allows the EEPROM layer to send a single i2c write command
per page, and wait CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS between
i2c write commands.
Signed-off-by: NMichael Jones <michael.jones@matrix-vision.de>
Acked-by: NHeiko Schocher <hs@denx.de>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Read directly from OMAP_GPIO_DATAOUT to get the output state of the GPIO pin
Signed-off-by: NJoel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: NJason Kridner <jkridner@beagleboard.org>
Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>

Cleanup tx25.h by removing unnecessary defines and by removing unneeded "1"'s.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

Make use of GPIO framework and avoid the following build error:

tx25.c: In function 'tx25_fec_init':
tx25.c:73: error: dereferencing pointer to incomplete type
tx25.c:74: error: dereferencing pointer to incomplete type
tx25.c:75: error: dereferencing pointer to incomplete type
tx25.c:76: error: dereferencing pointer to incomplete type
tx25.c:83: error: dereferencing pointer to incomplete type
tx25.c:84: error: dereferencing pointer to incomplete type
tx25.c:114: error: dereferencing pointer to incomplete type
tx25.c:115: error: dereferencing pointer to incomplete type
tx25.c:116: error: dereferencing pointer to incomplete type
tx25.c:117: error: dereferencing pointer to incomplete type
tx25.c:124: error: dereferencing pointer to incomplete type
tx25.c:125: error: dereferencing pointer to incomplete type
tx25.c:126: error: dereferencing pointer to incomplete type
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NStefano Babic <sbabic@denx.de>

This patch fixes the warning dure to recent changes to the board
configuration:
cmd_i2c.o cmd_i2c.c -c
cmd_i2c.c:109:1: warning: missing braces around initializer
cmd_i2c.c:109:1: warning: (near initialization for 'i2c_no_probes[0]')
Signed-off-by: NSanjeev Premi <premi@ti.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Acked-by: NJason Kridner <jdk@ti.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Fix build problem:

nand_spl/board/davinci/da8xxevm/hawkboard_nand_spl.c: In function 'board_init_f':
nand_spl/board/davinci/da8xxevm/hawkboard_nand_spl.c:132: warning: implicit declaration of function 'nand_boot'
nand_spl/board/davinci/da8xxevm/hawkboard_nand_spl.c:133: warning: 'noreturn' function does return
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Syed Mohammed Khasim <sm.khasim@gmail.com>
Cc: Sughosh Ganu <urwithsughosh@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>

Fix these:
cm4008.c: In function 'board_eth_init':
cm4008.c:79: warning: implicit declaration of function 'ks8695_eth_initialize'

cm41xx.c: In function 'board_eth_init':
cm41xx.c:79: warning: implicit declaration of function 'ks8695_eth_initialize'

While we are at it, sort include list in netdev.h
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Greg Ungerer <greg.ungerer@opengear.com>

Commit 21726a7a "Add assert() for debug assertions" caused build
warnings for all tegra2 based boards:

clock.c:36:1: warning: "assert" redefined
In file included from clock.c:29:
include/common.h:144:1: warning: this is the location of the previous definition
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>

get_ram_size() is called, but memsize.c is not compiled.
Signed-off-by: NStefano Babic <sbabic@denx.de>

Trivial conversion of the ks8695eth driver to a CONFIG_MULTI_ETH type
driver.
Signed-off-by: NGreg Ungerer <greg.ungerer@opengear.com>

The pointer to the flash based bootargs should be a "char *", not unsigned.
Fixes:

cm41xx.c: In function ‘env_flash_cmdline’:
cm41xx.c:67: warning: pointer targets in passing argument 2 of ‘setenv’ differ in signedness
Signed-off-by: NGreg Ungerer <greg.ungerer@opengear.com>

The pointer to the flash based bootargs should be a "char *", not unsigned.
Fixes:

cm4008.c: In function ‘env_flash_cmdline’:
cm4008.c:67: warning: pointer targets in passing argument 2 of ‘setenv’ differ in signedness
Signed-off-by: NGreg Ungerer <greg.ungerer@opengear.com>

Commit 21726a7a "Add assert() for debug assertions" broke building the
utx8245 board:

dlmalloc.c: In function 'do_check_chunk':
dlmalloc.c:1660: error: 'sz' undeclared (first use in this function)
dlmalloc.c:1660: error: (Each undeclared identifier is reported only once
dlmalloc.c:1660: error: for each function it appears in.)
dlmalloc.c: In function 'do_check_free_chunk':
dlmalloc.c:1689: error: 'next' undeclared (first use in this function)
dlmalloc.c: In function 'do_check_malloced_chunk':
dlmalloc.c:1748: error: 'sz' undeclared (first use in this function)
dlmalloc.c:1750: error: 'room' undeclared (first use in this function)
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>

Commit 46d7274c "UBIFS: Change ubifsload to set the filesize variable"
introduced the follwing compiler warning:

ubifs.c: In function 'ubifs_load':
ubifs.c:742: warning: format '%lX' expects type 'long unsigned int', but argument 3 has type 'u32'
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Bastian Ruppert <Bastian.Ruppert@Sewerin.de>

Commit 21726a7a "Add assert() for debug assertions" caused build
warnings for many systems:

In file included from bedbug.c:6:
/home/wd/git/u-boot/work/include/bedbug/bedbug.h:24:1: warning: "assert" redefined
In file included from bedbug.c:3:
/home/wd/git/u-boot/work/include/common.h:144:1: warning: this is the location of the previous definition
In file included from cmd_bedbug.c:10:
/home/wd/git/u-boot/work/include/bedbug/bedbug.h:24:1: warning: "assert" redefined
In file included from cmd_bedbug.c:5:
/home/wd/git/u-boot/work/include/common.h:144:1: warning: this is the location of the previous definition
Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: NSimon Glass <sjg@chromium.org>

* 'master' of git://git.denx.de/u-boot-mpc85xx:
  powerpc/mpc8610hpcd: set pci1_hose.config_table after fsl_setup_hose
  powerpc/mpc8548cds: set pci1_hose.config_table after fsl_setup_hose
  powerpc/mpc8568mds: set pci1_hose.config_table after fsl_setup_hose

Use _bss_start_ofs as the size of the boot loader code+data that we want
to protect in the flash. This replaces use of the no longer defined
_armboot_start.

Fixes:

flash.c: In function ‘flash_init’:
flash.c:75: error: ‘_bss_start’ undeclared (first use in this function)
flash.c:75: error: (Each undeclared identifier is reported only once
flash.c:75: error: for each function it appears in.)
flash.c:75: error: ‘_armboot_start’ undeclared (first use in this function)

Signed-off-by: <greg.ungerer@opengear.com>

The OpenGear boards CM4008, CM4116 and CM4148 need their DRAM base
and RAM stack base addresses defined.

Fixes:

board.c: In function ‘__dram_init_banksize’:
board.c:227: error: ‘CONFIG_SYS_SDRAM_BASE’ undeclared (first use in this function)
board.c:227: error: (Each undeclared identifier is reported only once
board.c:227: error: for each function it appears in.)
board.c: In function ‘board_init_f’:
board.c:270: error: ‘CONFIG_SYS_INIT_SP_ADDR’ undeclared (first use in this function)
board.c:303: error: ‘CONFIG_SYS_SDRAM_BASE’ undeclared (first use in this function)
Signed-off-by: NGreg Ungerer <greg.ungerer@opengear.com>

Move the TIMER_ definitions before they are used in KS8695 timer.c code.
Fixes:

timer.c: In function ‘timer_init’:
timer.c:37: error: ‘TIMER_COUNT’ undeclared (first use in this function)
timer.c:37: error: (Each undeclared identifier is reported only once
timer.c:37: error: for each function it appears in.)
timer.c:38: error: ‘TIMER_PULSE’ undeclared (first use in this function)
Signed-off-by: NGreg Ungerer <greg.ungerer@opengear.com>

This change slightly improves readability of the phydev speed/duplex
assignment logic.
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Acked-by: NDetlev Zundel <dzu@denx.de>

This change allows to cope with a mii bus device registered using
miiphy_register(), which doesn't assign a default reset handler.
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Acked-by: NDetlev Zundel <dzu@denx.de>

This is the same behaviour like tftp or fatload command.
Signed-off-by: NBastian Ruppert <Bastian.Ruppert@Sewerin.de>
CC: kmpark@infradead.org
Acked-by: NDetlev Zundel <dzu@denx.de>

assert() is like BUG_ON() but compiles to nothing unless DEBUG is defined.
This is useful when a condition is an error but a board reset is unlikely
to fix it, so it is better to soldier on in hope. Assertion failures should
be caught during development/test.

It turns out that assert() is defined separately in a few places in U-Boot
with various meanings. This patch cleans up some of these.

Build errors exposed by this change (and defining DEBUG) are also fixed in
this patch.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Pick them up automatically using $(boards_by_arch ...)
Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>

Fix these:
yaffs_guts.c: In function 'yaffs_ReadDataFromFile':
yaffs_guts.c:4622: warning: pointer targets in passing argument 3 of 'yaffs_AddrToChunk' differ in signedness
yaffs_guts.c:4622: warning: pointer targets in passing argument 4 of 'yaffs_AddrToChunk' differ in signedness
yaffs_guts.c: In function 'yaffs_WriteDataToFile':
yaffs_guts.c:4745: warning: pointer targets in passing argument 3 of 'yaffs_AddrToChunk' differ in signedness
yaffs_guts.c:4745: warning: pointer targets in passing argument 4 of 'yaffs_AddrToChunk' differ in signedness
yaffs_guts.c: In function 'yaffs_ResizeFile':
yaffs_guts.c:4968: warning: pointer targets in passing argument 3 of 'yaffs_AddrToChunk' differ in signedness
yaffs_guts.c:4968: warning: pointer targets in passing argument 4 of 'yaffs_AddrToChunk' differ in signedness
yaffs_guts.c: In function 'yaffs_GutsInitialise':
yaffs_guts.c:7235: warning: assignment from incompatible pointer type
yaffs_guts.c: In function 'yaffs_CreateNewObject':
yaffs_guts.c:2143: warning: 'tn' may be used uninitialized in this function
yaffs_guts.c: In function 'yaffs_MknodObject':
yaffs_guts.c:2258: warning: 'str' may be used uninitialized in this function
Signed-off-by: NWolfgang Denk <wd@denx.de>

Fix these:
yaffs_guts.c: At top level:
yaffs_guts.c:400: warning: 'yaffs_SkipFullVerification' defined but not used

Testing shows no changes of the image sizes.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Fix these:
yaffs_guts.c: In function 'yaffs_Scan':
yaffs_guts.c:5436: warning: pointer targets in passing argument 4 of 'yaffs_QueryInitialBlockState' differ in signedness
yaffs_guts.c: In function 'yaffs_ScanBackwards':
yaffs_guts.c:6017: warning: pointer targets in passing argument 4 of 'yaffs_QueryInitialBlockState' differ in signedness
yaffs_nand.c: In function 'yaffs_QueryInitialBlockState':
yaffs_nand.c:109: warning: pointer targets in passing argument 4 of 'dev->queryNANDBlock' differ in signedness
yaffs_nand.c:113: warning: pointer targets in passing argument 4 of 'yaffs_TagsCompatabilityQueryNANDBlock' differ in signedness
Signed-off-by: NWolfgang Denk <wd@denx.de>

Drop the "-DNO_Y_INLINE" setting to fix these:
yaffs_guts.h:806: warning: 'yaffs_GetBlockInfo' defined but not used

Impact on image size is negligible - for the VCMA9 board the text
segment size grew from 496353 to 496357 bytes (i. e. 0.0008%);
total image size even remained constant.
Signed-off-by: NWolfgang Denk <wd@denx.de>

Fix these:
yaffscfg.c: In function 'cmd_yaffs_mread_file':
yaffscfg.c:316: warning: format '%08x' expects type 'unsigned int', but argument 3 has type 'char *'
yaffscfg.c: In function 'cmd_yaffs_ls': yaffscfg.c:371: warning: format '%7d' expects type 'int', but argument 3 has type 'off_t'
Signed-off-by: NWolfgang Denk <wd@denx.de>