When U-Boot boots from EL2, skip some lowlevel init code requiring
EL3, including CCI-400/CCN-504, trust zone, GIC, etc. These
initialization tasks are carried out before U-Boot runs. This applies
to the RAM version image used for SPL boot if PPA is loaded first.
Signed-off-by: NYork Sun <york.sun@nxp.com>

Signed-off-by: NSantan Kumar <santan.kumar@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: NAbhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Add CONFIG_NAND_BOOT config flag to organise
NAND_BOOT specific code in config flag like
-nand-boot specfic errata errata_rcw_src()
-CONFIG_SYS_NAND_U_BOOT_DST,etc
Signed-off-by: NSantan Kumar <santan.kumar@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: NAbhimanyu Saini <abhimanyu.saini@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

modify u_qe_init to upload QE firmware from SD card when it is SD
boot
Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Previous to MC v10.x, port mac address was specified via DPL. Since
newer MC versions are compatible with old style DPLs, make the u-boot
env mac addresses visible there. This applies only to DPLs that have
an older version.

DPLs use 32 bit values for specifying MAC addresses. U-boot
environment variables take precedence over the MAC addresses already
visible in the DPL/DPC.
Signed-off-by: NBogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: NHeinz Wrobel <heinz.wrobel@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

DPAA2 platforms boot the Management Complex based on the u-boot env
variable "mcinitcmd". Instead of doing this step on each platform
individually, define a single mc_env_boot function in the MC driver,
since it's semantically tied to it.

Call the function in a per-board reset_phy hook, as it gets called at a
later moment, when all board PHY devices have been initialized.
Signed-off-by: NBogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: NHeinz Wrobel <heinz.wrobel@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Move FTMAC100 to where it should be, alphabetically in
drivers/net/Kconfig
Signed-off-by: NTom Rini <trini@konsulko.com>

Conflicts:
	drivers/net/Kconfig

This patch adjusts memory map for secure boot headers on LS2080AQDS
and LS2080ARDB platforms. Secure boot headers are placed on NOR
flash at offset 0x00600000.
Signed-off-by: NUdit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

This patch adjusts memory map for images on LS2080ARDB and
LS2080AQDS NOR flash as below

Image				Flash Offset
RCW+PBI				0x00000000
Boot firmware (U-Boot)		0x00100000
Boot firmware Environment	0x00300000
PPA firmware			0x00400000
PHY firmware			0x00980000
DPAA2 MC			0x00A00000
DPAA2 DPL			0x00D00000
DPAA2 DPC			0x00E00000
Kernel.itb			0x01000000
Signed-off-by: NSantan Kumar <santan.kumar@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

This patch is to adjust the memory mapping for FLash/SD card on
LS1046AQDS and LS1046ARDB, such as FMAN firmware load address, U-Boot
start address on serial flash and environment address.
Signed-off-by: NAlison Wang <alison.wang@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

This patch is to adjust the memory mapping for FLash/SD card on
LS1043AQDS and LS1043ARDB, such as PPA firmware load address, FMAN
firmware load address, QE firmware load address, U-Boot start address
on serial flash and environment address.
Signed-off-by: NAlison Wang <alison.wang@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

This patch is to adjust the memory mapping for FLash/SD card on
LS1021AQDS and LS1021ATWR, such as U-Boot start address on serial
Flash, QE firmware load address and environment address.
Signed-off-by: NAlison Wang <alison.wang@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

LS2081ARDB board is similar to LS2080ARDB board with few differences
 It hosts LS2081A SoC
 Default boot source is QSPI-boot
 It does not have IFC interface
 RTC and QSPI flash device are different
 It provides QIXIS access via I2C
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: NSantan Kumar <santan.kumar@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

The QorIQ LS2081A SoC has eight 64-bit ARM v8 Cortex A72 cores and
is built on layerscape architecture. It is 40-pin derivative of
LS2084A (non-AIOP personality of LS2088A). So feature-wise it is
same as LS2084A. LS2041A is a 4-core personality of LS2081A.
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: NSantan Kumar <santan.kumar@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: NSuresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Update QIXIS related code to be executed only if CONFIG_FSL_QIXIS
flag is enabled. In case QIXIS code is not enabled, use default
sysclk value as 100MHz per board documentation.
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Earlier when MC is loaded but DPL is not deployed results in FDT
fix-up code execution hangs. For this case now print message on
console and return success instead of return -ENODEV. This update
allows fdt fixup to continue execution.
Signed-off-by: NYogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: NPriyanka Jain <Priyanka.jain@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

This allows using PCIe NIC without enabling DPAA FMan.
Signed-off-by: NYork Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: NMingkai Hu <mingkai.hu@nxp.com>

This allows using PCIe NIC without enabling DPAA FMan.
Signed-off-by: NYork Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: NMingkai Hu <mingkai.hu@nxp.com>

LS1012AFRDM, LS1012ARDB, LS1012AQDS all have S25FS512S flash
of 64MB size.
Signed-off-by: NSuresh Gupta <suresh.gupta@nxp.com>

ls1012ardb, ls1046ardb, ls2080ardb have S25FS512S flash which does
not support Bank Address Register commands.
Signed-off-by: NSuresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

LS2080ARDB/LS2088ARDB RevF board has smart voltage translator
which needs to be programmed to enable high speed SD interface
by setting GPIO4_10 output to zero.
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: NSantan Kumar <santan.kumar@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

Support Andestech eth ftmac100 device tree flow on AG101P/AE3XX platform.
Verification:
 Boot linux kernel via dhcp and bootm ok.

 NDS32 # setenv bootm_size 0x2000000;setenv fdt_high 0x1f00000;
 NDS32 # dhcp 0x600000 10.0.4.97:boomimage-310y-ae300-spi.bin
 BOOTP broadcast 1
 BOOTP broadcast 2
 BOOTP broadcast 3
 BOOTP broadcast 4
 DHCP client bound to address 10.0.4.178 (4899 ms)
	Using mac@e0100000 device
	TFTP from server 10.0.4.97; our IP address is 10.0.4.178
	Filename 'boomimage-310y-ae300-spi.bin'.
	Load address: 0x600000
	Loading: #################################################################
	         #################################################################
	         #################################################################
...
...
	         ###################################
	         233.4 KiB/s
					 done
					 Bytes transferred = 13872076 (d3abcc hex)
	NDS32 # dhcp 0x2000000 10.0.4.97:ae300.dtb
	BOOTP broadcast 1
	BOOTP broadcast 2
	BOOTP broadcast 3
	BOOTP broadcast 4
	DHCP client bound to address 10.0.4.178 (4592 ms)
	Using mac@e0100000 device
	TFTP from server 10.0.4.97; our IP address is 10.0.4.178
	Filename 'ae300.dtb'.
	Load address: 0x2000000
	Loading: #
	         82 KiB/s
					 done
					 Bytes transferred = 2378 (94a hex)
	NDS32 # bootm 0x600000 - 0x2000000
	 Image Name:
	 Created:      2017-03-22   6:52:03 UTC
	 Image Type:   NDS32 Linux Kernel Image (uncompressed)
	 Data Size:    13872012 Bytes = 13.2 MiB
	 Load Address: 0000c000
	 Entry Point:  0000c000
	 Verifying Checksum ... OK
	 Booting using the fdt blob at 0x2000000
	 Loading Kernel Image ... OK
	 Loading Device Tree to 01efc000, end 01eff949 ... OK
	 Linux version 3.10.102-20375-gb0034c1-dirty (rick@app09)
	(gcc version 4.9.3 (2016-07-06_nds32le-linux-glibc-v3_experimental) )
  #293 PREEMPT Wed Mar 22 14:49:28 CST 2017
	CPU: NDS32 N13, AndesCore ID(wb), CPU_VER 0x0d11103f(id 13, rev 17, cfg 4159)
...
...
Signed-off-by: Nrick <rick@andestech.com>

In situations like an autobuilder we are likely to not have bl31.bin
present and thus would fail to build and propagate the error upwards.
Instead, print a big warning to stderr so that human will see that
something is wrong but complete the build.

Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NTom Rini <trini@konsulko.com>

trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).
Signed-off-by: NTom Rini <trini@konsulko.com>

The original commit for the MCF54418TWR ColdFire development board
support defined a 'CONFIG_SYS_FAULT_ECCONFIG_SYS_NO_FLASHHO_LINK_DOWN'
which obviously has a rogue 'CONFIG_SYS_NO_FLASH' embedded in the
intended 'CONFIG_SYS_FAULT_ECHO_LINK_DOWN' define.
Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>

Enable this option by default on sandbox to increase build coverage.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_CMD_LZMADEC
Signed-off-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_LZMA
Signed-off-by: NSimon Glass <sjg@chromium.org>

This is not used in U-Boot. Drop it.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_CMD_KGDB
Signed-off-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_CMD_IRQ
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NTom Rini <trini@konsulko.com>

Rather than using CMD_JFFS2 for both the filesystem and its command, we
should have a separate option for each. This allows us to enable JFFS2
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_CMD_JFFS2
Signed-off-by: NSimon Glass <sjg@chromium.org>

This converts the following to Kconfig:
   CONFIG_CMD_IOTRACE
Signed-off-by: NSimon Glass <sjg@chromium.org>