GDT limit should be one less than an integral multiple of eight.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>

When building U-Boot with CONFIG_X86_RESET_VECTOR, the linking
process misses the resetvec.o and start16.o so it cannot generate
the rom version of U-Boot. The arch/x86/cpu/Makefile is updated to
pull them into the final linking process.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NSimon Glass <sjg@chromium.org>

Add a new setup@ section to the FIT which can be used to provide a setup
binary for booting Linux on x86. This makes it possible to boot x86 from
a FIT.
Signed-off-by: NSimon Glass <sjg@chromium.org>

This uses cfg instead of conf, and img instead of image. Fix these and
update in a few other places.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Since sandbox is used for testing, it should be able to 'boot' an image
from any archhitecture. This allows us to test an image by loading it in
sandbox.
Signed-off-by: NSimon Glass <sjg@chromium.org>

If we are passing this using the device tree then we may not want to
set this up here.
Signed-off-by: NSimon Glass <sjg@chromium.org>

The x86 bootm code is quite special, and geared to zimage. Adjust it
to support device tree and make it more like the ARM code, with
separate bootm stages and functions for each stage.

Create a function announce_and_cleanup() to handle printing the
"Starting kernel ..." message and put it in bootm so it is in one
place and can be used by any loading code. Also move the
board_final_cleanup() function into bootm.
Signed-off-by: NSimon Glass <sjg@chromium.org>

These options are used by the image code. To allow us to use the generic
code more easily, define these for x86.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Enable blob commands for platforms having SEC 4.0 or greater
for secure boot scenarios
Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Freescale's SEC block has built-in Blob Protocol which provides
a method for protecting user-defined data across system power
cycles. SEC block protects data in a data structure called a Blob,
which provides both confidentiality and integrity protection.

Encapsulating data as a blob
Each time that the Blob Protocol is used to protect data, a
different randomly generated key is used to encrypt the data.
This random key is itself encrypted using a key which is derived
from SoC's non volatile secret key and a 16 bit Key identifier.
The resulting encrypted key along with encrypted data is called a blob.
The non volatile secure key is available for use only during secure boot.

During decapsulation, the reverse process is performed to get back
the original data.

Commands added
--------------
    blob enc - encapsulating data as a cryptgraphic blob
    blob dec - decapsulating cryptgraphic blob to get the data

Commands Syntax
---------------
	blob enc src dst len km

	Encapsulate and create blob of data $len bytes long
	at address $src and store the result at address $dst.
	$km is the 16 byte key modifier is also required for
	generation/use as key for cryptographic operation. Key
	modifier should be 16 byte long.

	blob dec src dst len km

	Decapsulate the  blob of data at address $src and
	store result of $len byte at addr $dst.
	$km is the 16 byte key modifier is also required for
	generation/use as key for cryptographic operation. Key
	modifier should be 16 byte long.
Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

By default, PAMU's (IOMMU) are enabled in case of secure boot.
Disable/bypass them once the control reaches the bootloader.

For non-secure boot, PAMU's are already bypassed in the default
SoC configuration.
Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Hardware accelerated support for SHA-1 and SHA-256 has been added.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Enable CAAM in platforms supporting the hardware block.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

SHA-256 and SHA-1 accelerated using SEC hardware in Freescale SoC's
The driver for SEC (CAAM) IP is based on linux drivers/crypto/caam.
The platforms needto add the MACRO CONFIG_FSL_CAAM inorder to
enable initialization of this hardware IP.
Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

SEC registers can be of type Little Endian or big Endian depending upon
Freescale SoC. Here SoC defines the register type of SEC IP.

So update acessor functions with common SEC acessor functions to take care
both type of endianness.
Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

Freescale SEC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the CCSR defintion of
SEC to common include
Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: NYork Sun <yorksun@freescale.com>

U-boot binary size has been increased from 512KB to 768KB.

So update CONFIG_RESET_VECTOR_ADDRESS to reflect the same for
P1010 SPI Flash Secure boot target.
Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com>
[York Sun: Modified subject to P1010RDB]
Reviewed-by: NYork Sun <yorksun@freescale.com>

The ipu display insists on having a lower_margin smaller
then 2. If this is not the case it will attempt to force
it and adjust the pixclk accordingly. This multiplies pixclk
in Hz with the width and height, since this is typically
a * 10^7 * b * 10^2 * c * 10^2 this will overflow the
uint_32 and make things even worse. Since this is a
bootloader and the adjustment is neglectible, just force
it to two and warn about it.

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: NJeroen Hofstee <jeroen@myspectrum.nl>

- fix debug pixel clk display and add unit
- fix some comments

Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: NJeroen Hofstee <jeroen@myspectrum.nl>

Add a block to avoid a build error with the variable declaration.
Enable the option on sandbox to prevent an error being introduced in
future.
Signed-off-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NTom Rini <trini@ti.com>

Currently uboot wrongly uses 25mV / step for dcdc3, this is a copy and paste
error introduced when adding the axp152_mvolt_to_target during review of the
axp152.c driver. This results in u-boot setting Vddr to 2.3V instead of 1.5V.

This commit fixes this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>

With the introduction of CONFIG_LOCALVERSION support we cannot build
tools without having a config file (as we won't know our PLAIN_VERSION
until then).
Reported-by: NOtavio Salvador <otavio@ossystems.com.br>
Signed-off-by: NTom Rini <trini@ti.com>

The SoCDK uses EMAC1, not EMAC0. This patch fixes the issue.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>

Add MAINTAINERS entry.
Signed-off-by: NPavel Machek <pavel@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>

Commit 832472 "tools: socfpga: Add socfpga preloader signing
to mkimage" added tools/socfpga.c which relies on htole32,
le32toh and friends. While compiler.h includes these protypes
for linux from endian.h, it doesn't do so for FreeBSD. Hence
include <sys/endian.h> for FreeBSD.

Cc: Marek Vasut <marex@denx.de>
CC: Tom Rini <trini@ti.com>
Signed-off-by: NJeroen Hofstee <jeroen@myspectrum.nl>

Signed-off-by: NHeiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: NBo Shen <voice.shen@atmel.com>
Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>

Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>

Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Bo Shen <voice.shen@atmel.com>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>

Update readme file for Keystone II EVM boards to actual sources.
Also correct some typos. For now the Edison evaluation board is
added, README for K2E is mostly the same, so update README to
contain information also for K2E evm. Rename file to README as
it contains information for all keystone evm boards.
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>

The K2HK and K2E boards support SPL by default, so add
CONFIG_SPL option. Also export CONFIG_ARM, CONFIG_ARCH_KEYSTONE
and TARGET_K2*_EVM options to spl/.config as they are the same.
So now it's convinient to build gph images using only two commands:

make k2hk_evm_defconfig
make u-boot-spi.gph
Acked-By: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NIvan Khoronzhuk <ivan.khoronzhuk@ti.com>

We need to set the 'BE' flag here for things to work right.
Signed-off-by: NTom Rini <trini@ti.com>