Enable CMD_GPIO for board ls1046aqds
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CMD_GPIO for board ls1046ardb
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CMD_GPIO for board ls1043ardb
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CMD_GPIO for board ls1043aqds
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CMD_GPIO for board ls1028ardb
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CMD_GPIO for board ls1028aqds
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CMD_GPIO for ls1021atwr
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CMD_GPIO for board ls1021aqds
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CMD_GPIO for ls1012ardb
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CMD_GPIO for ls1012afrwy
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CONFIG_MPC8XXX_GPIO for board ls1021aqds
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CONFIG_MPC8XXX_GPIO for board ls1021atwr
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable MPC8XXX_GPIO for SoC LS1046A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CONFIG_MPC8XXX_GPIO for SoC LX2160A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CONFIG_MPC8XXX_GPIO for LS208xA
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CONFIG_MPC8XXX_GPIO for LS1088A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CONFIG_MPC8XXX_GPIO for SoC LS1028A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CONFIG_MPC8XXX_GPIO for SoC LS1043A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable CONFIG_MPC8XXX_GPIO for SoC LS1012A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Add gpio node for SoC LS208xA
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Add gpio node for SoC LS1088A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Add gpio node for SoC LS1046A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Add gpio node for SoC LS1043A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Add gpio node for SoC LS1028A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Add gpio node for SoC LS1012A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Add gpio node for SoC LS1021A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Update gpio driver to use same logic for big-endian and little-endian
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Drop the CONFIG_VIDEO to fix the following build warning.
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
UPD     include/generated/dt.h
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
UPD     include/generated/timestamp_autogenerated.h
====================================================
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Update data type of '1' to '1ull' in below assignment
size = 1ull << sizebit;

to fix incorrect assignment issue.
e.g: when sizebit was 31, 0x80000000 got sign extended to
0xffffffff_80000000
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
Reported-by: NDean Saridakis <dean.saridakis@baesystems.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Enable the I-Cache to speed up the boot time, especailly for the NOR
boot, currently it takes about 15 seconds from power up to the U-Boot
prompt, and with the I-Cache enabled it only takes around 2.5 seconds.
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Cleanup, move the declarations to keymile/common.h instead declaring them
per-board config.h
Signed-off-by: NAleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

LX2162A is not like LX2160A which has different PCIe controller
in rev1 and rev2 silicon. It supports only one configuration of
PCIe controller, which is same as LS2088A. So update PCIe
compatible string same as LS2088A.
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: NWasim Khan <wasim.khan@nxp.com>
Tested-by: NWasim Khan <wasim.khan@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

This patch moves the SVR definitions to a new svr.h for
Layerscape armv7 and armv8 platforms respectively, so that
the PCIe driver can reuse them.
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: NWasim Khan <wasim.khan@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

The LS1088 requires the same QUADSPI_QURIK_BASE_INTERNAL
workaround as the LS208x and also has a 64 byte TX buffer.

With the previous settings SPI-NAND reads over AHB were
corrupted.

Fixes: 91afd36f ("spi: Transform the FSL QuadSPI driver to use the SPI MEM API")
Signed-off-by: NMathew McBride <matt@traverse.com.au>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Adapted from kernel commit b0177aca7aea
From: Michael Walle <michael@walle.cc>

Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.

Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.

Fixes: 91afd36f ("spi: Add a driver for the Freescale/NXP QuadSPI controller")
Signed-off-by: NMichael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200114154613.8195-1-michael@walle.ccSigned-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: Mathew McBride <matt@traverse.com.au> [adapt for U-Boot]
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

spi_mem_default_supports_op is used internally by controller
drivers to verify operation semantics are correct.

It is used internally inside spi-mem but has not (in U-Boot)
been declared in spi-mem.h for external use.
Signed-off-by: NMathew McBride <matt@traverse.com.au>
Reviewed-by: NPratyush Yadav <p.yadav@ti.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Add basic support for the Hitachi Power Grids kmcent2 board, based
on the NXP QorIQ T1040 SoC.
Signed-off-by: NValentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Signed-off-by: NRainer Boschung <rainer.boschung@hitachi-powergrids.com>
Signed-off-by: NNiel Fourie <lusus@denx.de>
Cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: NStefan Roese <sr@denx.de>
[Fixed blank line at EOF errors]
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Replace instances of sprintf()/set_env() for setting hexadecimal
values with set_env_hex().

In set_km_env() the "pram" variable was set to an hexadecimal
value, while initr_mem() expects an unsigned decimal, so use
set_env_ulong() instead.
Signed-off-by: NNiel Fourie <lusus@denx.de>
Cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: NStefan Roese <sr@denx.de>
[Rebased]
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Pulled in the kmcent2.dts and all its dependents from Linux 5.10,
commit 2c85ebc57b3e upstream. Replaced the license text with
SPDX License Identifiers.
Signed-off-by: NNiel Fourie <lusus@denx.de>
Cc: Holger Brunck <holger.brunck@hitachi-powergrids.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: NStefan Roese <sr@denx.de>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Take into account SDRAM_BASE address when calculating pnvramaddr and
varaddr offsets.
Up to now Keymile designs had SDRAM_BASE equal to zero and the offsets
where calculated correctly, this fix is for the upcoming designs that
have SDRAM_BASE different then zero.
Signed-off-by: NAleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>