MVS1 board has reached end-of-life and can be removed completely.
Signed-off-by: NAndre Schwarz <andre.schwarz@matrix-vision.de>

fix mvBL-M7 config and move to matrix_vision subdir
Signed-off-by: NAndre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>

Signed-off-by: NKim Phillips <kim.phillips@freescale.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The MIMC200 board is based on Atmel's NGW100 dev kit, but with an extra
8MByte FLASH and 128KByte FRAM.
Signed-off-by: NMark Jackson <mpfj@mimc.co.uk>
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>

The 'license' command includes the U-Boot license (GPLv2) into the
actual bootloader binary. The license text can be shown interactively
at the U-Boot commandline.

For products where the commandline can actually be accessed by the
end user, this helps to prevent inadvertent GPL violations, since the
GPLv2 license text can no longer be 'forgotten' to be included into
the product.

The 'license' command can be enabled by CONFIG_CMD_LICENSE.
Signed-off-by: NHarald Welte <laforge@openmoko.org>

Signed-off-by: NTsiChung Liew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: NTsiChung Liew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: NTsiChung Liew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: NTsiChung Liew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: NTsiChung Liew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: NTsiChung Liew <Tsi-Chung.Liew@freescale.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Note that with older board revisions, NAND boot may only work after a
power-on reset, and not after a warm reset.  I don't have a newer board
to test on; if you have a board with a 33MHz crystal, please let me know
if it works after a warm reset.
Signed-off-by: NScott Wood <scottwood@freescale.com>

Signed-off-by: NWilliam Juul <william.juul@tandberg.com>

To use YAFFS2 define CONFIG_YAFFS2
Signed-off-by: NWilliam Juul <william.juul@tandberg.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>

This patch adds support for the Favr-32 board made by EarthLCD.

This kit, which is also called ezLCD-101 when running with EarthLCD firmware,
has a 10.4" touch screen LCD panel, 16 MB 32-bit SDRAM, 8 MB parallel flash,
Ethernet, audio out, USB device, SD-card slot, USART and various other
connectors for cennecting stuff to SPI, I2C, GPIO, etc.
Signed-off-by: NHans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>

Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

- Relocate the location of U-Boot in the flash
- Save the environment in one sector of the flash memory
- MTD Support
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: NStefan Roese <sr@denx.de>

This patch allows booting from FLASH the ML507 board by Xilinx.
Previously, U-Boot needed to be loaded from JTAG or a Sytem ACE CF
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@uam.es>
Signed-off-by: NStefan Roese <sr@denx.de>

The Hammerhead platform is built around a AVR32 32-bit microcontroller
from Atmel.  It offers versatile peripherals, such as ethernet, usb
device, usb host etc.

The board also incooperates a power supply and is a Power over Ethernet
(PoE) Powered Device (PD).

Additonally, a Cyclone III FPGA from Altera is integrated on the board.
The FPGA is mapped into the 32-bit AVR memory bus. The FPGA offers two
DDR2 SDRAM interfaces, which will cover even the most exceptional need
of memory bandwidth. Together with the onboard video decoder the board
is ready for video processing.

For more information see: http:///www.miromico.com/hammerheadSigned-off-by: NJulien May <mailinglist@miromico.ch>
[haavard.skinnemoen@atmel.com: various small fixes and adaptions]
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>

Support for the adsvix was originally provided by Applied Data
Systems (ADS), inc., now EuroTech, Inc.
The board never shipped aside from some sample boards.
Signed-off-by: NAdrian Filipi <adrian.filipi@eurotech.com>

The Xilinx ML507 Board is a Virtex 5 prototyping board that includes,
	among others:
	-Virtex 5 FX FPGA (With a ppc440x5 in it)
	-256MB of SDRAM2
	-32MB of Flash
	-I2C Eeprom
	-System ACE chip
	-Serial ATA connectors
	-RS232 Level Conversors
	-Ethernet Transceiver

This patch gives support to a standard design produced by EDK for this
board: ppc440, uartlite, xilinx_int and flash

- Includes Changes propossed by Stefan Roese and Michal Simek
Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@uam.es>
Acked-by: NStefan Roese <sr@denx.de>

Signed-off-by: NStefan Roese <sr@denx.de>

Signed-off-by: NWolfgang Denk <wd@denx.de>

The MVBC_P is a MPC5200B based camera system with Intel Gigabit ethernet
controller (using e1000) and custom Altera Cyclone-II FPGA on PCI.
Signed-off-by: NAndre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add AMCC Redwood reference board that uses the latest
PPC 464 CPU processor combined with a rich mix of peripheral
controllers. The board will support PCIe, mutiple Gig ethernet
ports, advanced hardware RAID assistance and IEEE 1588.
Signed-off-by: NFeng Kan <fkan@amcc.com>
Signed-off-by: NStefan Roese <sr@denx.de>

ADS5121 Rev 3 board is now the default config

config targets are now

ads5121_config
    Rev 3 board with
	PCI
	M41T62 on board RTC
	512MB DRAM

ads5121_rev2_config
    Rev 2 board with
	No PCI
	256MB DRAM
Signed-off-by: NMartha Marx <mmarx@silicontkx.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NJohn Rigby <jrigby@freescale.com>

In order to consolidate more of the various MMC drivers around the
tree, we must first have a common place to put them.
Signed-off-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Acked-by: NJean-Chritophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Signed-off-by: NWolfgang Denk <wd@denx.de>

This patch adds support for the Lyrtech SFF-SDR board,
based on the TI DaVinci architecture (ARM926EJS).
Signed-off-by: NHugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: NPhilip Balister <philip@balister.org>
Signed-off-by: NWolfgang Denk <wd@denx.de>

This patch adds basic support for the TQM8548 module from TQ-Components
(http://www.tqc.de/) including DDR2 SDRAM initialisation and support for
eTSEC 3 and 4

Furthermore Flash buffer write has been enabled to speed up output to
the Flash by approx. a factor of 10.
Signed-off-by: NThomas Waehner <thomas.waehner@tqs.de>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>

This patch adds support for Linux kernels using the Flat Device Tree.
It also re-defines the default environment settings for booting Linux
with the FDT blob.
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>

Move all TQM board directories to the vendor specific directory "tqc"
for modules from TQ-Components GmbH (http://www.tqc.de).
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>

Add MPC8343 based board mvBlueLYNX-M7.
It's a single board stereo camera system.
Please read doc/README.mvblm7 for details.
Signed-off-by: NAndre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>

SH7763RDP has SCIF, NOR Flash, Ethernet, USB host, LCDC and MMC.
In this patch, support SCIF, NOR Flash, and Ethernet.
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>