- 16 4月, 2019 15 次提交
-
-
Post configuration cant be run at u-boot as u-boot didn't has any info about the design.So,this patch adds an info message that post config was not run and needs to be run manually if needed. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
This patch adds "zu39dr" to the list of zynqmp devices The zu39DR is the new RFSoC silicon with id value of 0x66. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Melin Tomas 提交于
Update EXTRA_ENV_SETTINGS and related commands to use 'setenv' instead of short name 'set' in commands. E.g. in case command setexpr is enabled the short form does not work properly as the name becomes ambigous. Fixes error messages like: U-Boot> set Unknown command 'set' - try 'help' Signed-off-by: NTomas Melin <tomas.melin@vaisala.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Hannes Schmelzer 提交于
The commit 'f48ef0d8' did break I2C support because requesting the clock for the I2C ip-block isn't supported during SPL. To fixup this we add support requesting clocks for: - i2c0 - i2c1 Signed-off-by: NHannes Schmelzer <hannes.schmelzer@br-automation.com> Reviewed-by: NHeiko Schocher <hs@denx.de> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
Remove unneeded configs from mini qspi configuration so that it saves space for this mini configuration. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
Define a label for flash node so that it can be referenced easily as required. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
spi-flash compatible string is needed for reading tx and rx bus widths, hence add this compatible string to flash node. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Just have better view on system. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 T Karthik Reddy 提交于
This patch checks for zynq aes & rsa commands max parameters count. Also checks minimum number of parameters count for aes command. Signed-off-by: NT Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 T Karthik Reddy 提交于
Changed the return type of reset_reason() to int from u32, because zynqmp_mmio_read/write() returns signed value on error. Replaced readl and writel functions with zynqmp_mmio_read & zynqmp_mmio_write functions to access RESET_REASON(CRL_APB) registers. Signed-off-by: NT Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
This patch fixes the tap delay values to be set at 100MHz and 150MHz as per TRM by fixing the if condition to use <= instead of <. Signed-off-by: NSiva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Do not enable WDT by default on this target because distributions are not enabling watchdog driver to service it. Feature has been enabled by: "arm64: zynqmp: Enable cadence WDT for zcu100" (sha1: 767afebb) And WDT is still enabled in rebranded Avnet Ultra 96 board support. Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Michal Simek 提交于
Images are created mkimage -f fit.its -E download-fit-external.ub and test expects these entries. env__fpga_under_test = { ... "mkimage_fit_external": download-fit-external.ub", "mkimage_fit_external_size": xxxxx, ... } Test download file and loads it to fpga. Signed-off-by: NMichal Simek <michal.simek@xilinx.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Tien Fong Chee 提交于
Ensure the string for filename is always constant, otherwise it can be corrupted by the writing. Signed-off-by: NTien Fong Chee <tien.fong.chee@intel.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
由 Tien Fong Chee 提交于
This function supports getting both data address and length for existing FPGA subimage and FPGA external data. Signed-off-by: NTien Fong Chee <tien.fong.chee@intel.com> Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
-
- 14 4月, 2019 1 次提交
-
-
git://git.denx.de/u-boot-spi由 Tom Rini 提交于
Conflicts: arch/arm/dts/armada-385-amc.dts arch/arm/dts/armada-xp-theadorable.dts arch/arm/dts/stm32mp157c-ev1-u-boot.dtsi Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 13 4月, 2019 7 次提交
-
-
git://git.denx.de/u-boot-dm由 Tom Rini 提交于
fdtdec tests and improvements for carve-outs pinctrl race-condition fix various other fixes in sandbox, sound, mkimage, etc.
-
git://git.denx.de/u-boot-mips由 Tom Rini 提交于
- mt76xx: add USB support, small fixes - ath79: small fixes, add support for QCA9563 SoC and AP152 reference board - mscc: small fixes, add network support for JR2 and ServalT SoCs - bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs - MIPS: fix redundant relocation of initrd images
-
https://github.com/patrickdelaunay/u-boot由 Tom Rini 提交于
stm32 patches for v2019.07-rc1 - Add trusted boot with TF-A for stm32mp1 - stm32mp1 dts files sync'ed with Linux version - add STM32MP1 Discovery boards (DK1 and DK2) - add STMFX gpio expander driver - misc improvement for stm3mp1 supports - rename stpmu1 to stpmic1 (official name) - stm32_qspi: move to exec_op (spi nor driver for stm32 mpu and mcu) - add STM32 FMC2 NAND flash controller driver
-
-
-
git://git.denx.de/u-boot-marvell由 Tom Rini 提交于
- Misc dts files sync'ed with Linux version (Chris) - Orion watchdog fix (Chris) - kwbimage changed to also support Marvell bin_hdr binary (Chris) - Add DM support to enable CONFIG_BLK for sata_mv (Stefan) - Enable BLK on multiple platforms (Stefan) - Misc minor fixes to AXP theadorable board (Stefan) - Correct logic for DM_SCSI + unconverted drivers check (stefan) - Misc changes to kirkwood to enable DM_USB here (Chris) - Change ahci_mvebu to enable usage on A38x (Baruch) - Update the kirkwood entry in git-mailrc (Baruch) - Misc minor improvements (turris, documentation) (Baruch) - Enhance sata_mv to support Kirkwood as well (Michael) - Add wdt command (Michael) - Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG board support (Chris)
-
由 Tom Rini 提交于
- Improve Keystone 3 SoC support (DMA, TI SCI) - Improve Keystone 2 SoC support (PHY fixes on various platforms) - Improve am335x families (new platforms, more boot mode options in SPL via DM). - General DaVinci, OMAP5 fixes.
-
- 12 4月, 2019 17 次提交
-
-
由 Stefan Roese 提交于
This patch enables USB and file-system support on the LinkIt smart MT7688 module for both, the normal and the RAM default config. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
-
由 Stefan Roese 提交于
This driver is derived from this Linux driver: linux/drivers/phy/ralink/phy-ralink-usb.c The driver sets up power and host mode, but also needs to configure PHY registers for the MT7628 and MT7688. I removed the reset controller handling for the USB host and device, as it does not seem to be necessary right now. The soft reset bits for both devices are enabled by default and testing has shown (with hackish reset handling added), that USB related commands work identical with or without the reset handling. Please note that the resulting USB support is tested only very minimal. I was able to detect one of my 3 currently available USB sticks. Perhaps some further work is needed to fully support the EHCI controller integrated in the MT76x8 SoC. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Reviewed-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>
-
由 Horatiu Vultur 提交于
Update default config to use network driver for ServalT SoCs. Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
-
由 Horatiu Vultur 提交于
Add ethernet nodes for ServalT SoCs family. Currently there is only one pcb(pcb116) in this family. Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
-
由 Horatiu Vultur 提交于
Add network driver for Microsemi Ethernet switch. It is present on ServalT SoCs. Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com> Reviewed-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com>
-
由 Horatiu Vultur 提交于
Shrink the environment size for 3 reasons: - reading the environment it is slow, therefore having a smaller env improves the speed. - usually in the environment there are only few variables, therefore the enviromnent is almost empty. - because the same image can run on different boards which may have different flashes with different page sizes, the CONFIG_ENV_SECT_SIZE can't be change, it is set to least common multiple of the page sizes. Adding this change improves the boot time. Before update for reading the entire environment it took ~850 msec, after the change it takes ~40 msecs. Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
-
由 Horatiu Vultur 提交于
Update default confing to use network driver for Jaguar2 SoCs. Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
-
由 Horatiu Vultur 提交于
Add ethernet nodes for Jaguar2 SoCs family. There are 3 pcb in this family: pcb110, pcb111 and pcb112. Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
-
由 Horatiu Vultur 提交于
In Jaguar2 SoC family there are 3 different pcb. Each of this needs to configure the phys in different ways. Therefore implement the function board_phy_config and based on pcb configure them accordingly. Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
-
由 Horatiu Vultur 提交于
Add network driver for Microsemi Ethernet switch. It is present on Jaguar2 SoCs. Reviewed-by: NDaniel Schwierzeck <daniel.schwierzeck@gmail.com> Signed-off-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
-
由 Philippe Reynes 提交于
Enable the gpio support (driver and command) in the configuration of the board bcm963158. Signed-off-by: NPhilippe Reynes <philippe.reynes@softathome.com>
-
由 Philippe Reynes 提交于
Enable all the gpio controllers in the device tree of the board bcm963158. Signed-off-by: NPhilippe Reynes <philippe.reynes@softathome.com>
-
由 Philippe Reynes 提交于
Add 8 gpio controllers in the bcm63158 device tree. Signed-off-by: NPhilippe Reynes <philippe.reynes@softathome.com>
-
由 Philippe Reynes 提交于
As no gpio.h is defined for this architecture, to avoid a compilation failure, do not include <asm/arch/gpio.h> for arch bcm63158. Signed-off-by: NPhilippe Reynes <philippe.reynes@softathome.com>
-
由 Philippe Reynes 提交于
This IP is also used on some arm SoC, so we allow to use this driver on arch bcm63158. Signed-off-by: NPhilippe Reynes <philippe.reynes@softathome.com>
-
由 Philippe Reynes 提交于
Enable the gpio support (driver and command) in the configuration of the board bcm968580xref. Signed-off-by: NPhilippe Reynes <philippe.reynes@softathome.com>
-
由 Philippe Reynes 提交于
Enable all the gpio controllers in the device tree of the board bcm968580xref. Signed-off-by: NPhilippe Reynes <philippe.reynes@softathome.com>
-