After moving the definition of CONFIG_SYS_TEXT_BASE to the respective
board config files, all Marvell kirkwood board have just a single and
common entry in their config.mk files:

	KWD_CONFIG = $(SRCTREE)/board/$(BOARDDIR)/kwbimage.cfg

Replace the only reference to KWD_CONFIG in the top level Makefile by
an equivalent setting, and remove all kirkwood config.mk files.

Signed-off-by: Wolfgang Denk <wd at denx.de>
Cc: Prafulla Wadaskar <prafulla at marvell.com>
Cc: Siddarth Gore <gores at marvell.com>
Cc: Simon Kagstrom <simon.kagstrom at netinsight.net>
Cc: Heiko Schocher <hs at denx.de>
Cc: Eric Cooper <ecc at cmu.edu>
Acked-by: Wolfgang Denk <wd at denx.de>
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>

Current default options increase u-boot size to overlap the location of the environment in NAND, move environment higher up
Signed-off-by: NGray Remlin <g_remlin@rocketmail.com>

It has been observed that, the complete u-boot banner
does not appear on the console when the system is booted
from NAND/NOR/SPI flash.

This patch fixes this issue on all Marvell boards by adding
board_early_init_f() support
Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>

- use internal 2k security SRAM as RAM for early stack.
- do early inits in board_init_f()
Signed-off-by: NHeiko Schocher <hs@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>

Appendix B "EHCI 64-Bit Data Structures" of the "Enhanced Host
Controller Interface Specification for Universal Serial Bus" (Rev.
1.0, March 12, 2002) defines additional fields which were missing in
U-Boot's struct qTD; as these are also present in recent versions of
struct ehci_qtd in the Linux kernel, we add them here, too.

This fixes some nasty memory corruption problems.
Reported-by: NDan Lykowski <lykowdk@gmail.com>
See http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/76942Signed-off-by: NWolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Dan Lykowski <lykowdk@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: NStefano Babic <sbabic@denx.de>

Removed warnings generated in the mx31_set_pad() function.
Signed-off-by: NStefano Babic <sbabic@denx.de>

Follow up to commit 620f1f6a
removed compiler warning for (now) unused cmd_tbl_t* cmdtp

This patch adds a small README to describe the usage of the
U-Boot UBI commands.
Signed-off-by: NStefan Roese <sr@denx.de>

The usage and help for the fpga command is wrong and incomplete,
and the parameters are not checked before to be passed to the
underlying subfunction.
Signed-off-by: NStefano Babic <sbabic@denx.de>

Add prototype function for ispVMFreeMem to remove warnings
when support for Lattice FPGA is compiled.
Signed-off-by: NStefano Babic <sbabic@denx.de>

The "options" field at the moment is only documented in the changelog
which isn't terribly useful to people without git.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

* update to support arm reloaction
* unnecessary environment variables removed
Signed-off-by: NJens Scharsig <js_at_ng@scharsoft.de>

This patch adds support for the HP Jornada flashboards
that were made in 2008. Older flashroms should work if
memory registers are adjusted.
Signed-off-by: NKristoffer Ericson <kristoffer.ericson@gmail.com>

Adpted for TEXT_BASE -> CONFIG_SYS_TEXT_BASE rename.
Removed now redundant board/jornada/config.mk file.
Removed unused empty jornada_init() function to silence
"jornada.c:35: warning: 'jornada_init' defined but not used"
Signed-off-by: NWolfgang Denk <wd@denx.de>

Boards often have a reserved size limit on the flash where they're stored.
Sometimes during upgrades or config changes, those limits are exceeded,
but no one notices until they try to upgrade and the limit screws things
up.  Either not enough of U-Boot is written to flash (and so the reboot
fails), or too much is written (and so things after it get clobbered).

So allow boards to declare a size limit (in bytes) and have the build
system check it while building.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Call fec_set_hwaddr in init routine to setup MAC address so when ethaddr is set
late via setenv the change will propagate to the hw.
Signed-off-by: NJohn Rigby <john.rigby@linaro.org>
CC: Ben Warren <biggerbadderben@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

NOTE: The modification in Makefile will be superseded by a pending patch!
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Firstly, this fixes relocation issues. I had to use part of Dcache as RAM for a
while. I also moved around the lowlevel init code. It turned out so most of the
lowlevel init code ended in cpu.c (and eventually was rewritten into C).

This will also allow easier operation with FDT, multi-CPU-model support etc. in
later releases.

NOTE: This breaks most of the PXA boards (actually, the reloc stuff did already,
this only finishes the doom).
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

pxa_mem_setup macro use r6 to store CONFIG_SYS_MDREFR_VAL during memory
initialization. This reg is modified during execution of pxa_wait_ticks.
Later we use r6 to setup MDREFR[APD] bit. As result MDREFR[APD] is always
zero.
Signed-off-by: NMikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>

Define ENV_ADDR as MONITOR_BASE + MONITOR_LEN. Fix environment sector
size (NOR: 32Kb for first four sectors and 128Kb for other; OneNAND: 128Kb).

Last but not least: we have MONITOR_LEN = 0x40000 and one sector for
environment (size = 0x20000), so the kernel may start from 0x00060000 only.
Signed-off-by: NMikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>

* CONFIG_SYS_CLKS_IN_HZ is not used anywhere, so removing it
* CONFIG_SYS_HZ is set to 1000 on most architectures, so it
  seems to be the safe default
Signed-off-by: NMikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>

This file is not used, automatically generated u-boot.lds is used instead
Signed-off-by: NMikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

The following hardware is currently supported:
- UART
- USB Host
- FPGA
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

128MB NOR module support.
Define __io to get harddrive working.
Fix saving of environment into OneNAND.
Boot from harddrive when possible.
Add missing MAINTAINERS entry.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

This patch adds support for the Palm Tungsten|C PXA255 board. The support
includes:
- LCD
- MMC
- UART
- NOR
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

This LCD panel is found in Palm LifeDrive handheld
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

ACX517AKN LCD panel is found in Palm Tungsten|C
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Also change the initializer style
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>