This adds support for the Gigadevice gd25lq128 ID needed on the
upcoming libretech-ac board.

SPI_NOR_QUAD_READ is not set since it has not been tested in Quad
mode.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NJagan Teki <jagan@amarulasolutions.com>

This patch update the behavior introduced by
commit 96907c0f ("dm: spi: Read default speed and mode values from DT")

In case of DT boot, don't read default speed and mode for SPI from
CONFIG_* but instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.

Remove also use in boards of the value speed=0 (no more supported)
for ENV in SPI by using CONFIG_ENV_SPI_MAX_HZ=0.

DT values will be always used when available (full DM support of
SPI slave with available DT node) even if speed and mode are requested;
for example in splash screen support (in splash_sf_read_raw)
or in SPL boot (in spl_spi_load_image).
The caller of spi_get_bus_and_cs() no more need to force speed=0.

But the current behavior don't change if the SPI slave is not
present (device with generic driver is created automatically)
or if platdata is used (CONFIG_OF_PLATDATA).
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Acked-by: NJagan Teki <jagan@amarulasolutions.com>

Replace the ad-hoc erase operation implementation with a simple spi_mem_op
implementation of the same functionality. This is a minor optimization and
removal of the ad-hoc code.

This however also changes the behavior of the execution of the erase
opcode from two separate transfer requests to the SPI NOR driver to
one transfer request to the SPI NOR driver. The former was how U-Boot
behaved before the SPI NOR framework was imported and the later was
introduced by the SPI NOR framework. The former is more optimal, so
keep that.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
Tested-by: NAshish Kumar <Ashish.kumar@nxp.com>

Update to prevent a byte of zeros being transmitted between
each byte in the tx buffer when providing both a tx buffer
and a rx buffer.
Signed-off-by: NJared Bents <jared.bents@rockwellcollins.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Acked-by: NJagan Teki <jagan@amarulasolutions.com>

Add check if exec_op is set before calling it.
At the moment it is called unconditionally, which leads to a crash if it
is not set correctly.
Signed-off-by: NBernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>
Reviewed-by: NJagan Teki <jagan@amarulasolutions.com>

A Coverity robot reported an integer handling issue
(OVERFLOW_BEFORE_WIDEN) in the potentially overflowing expression:

    (mtd_div_by_ws(mtd->size, mtd) - mtd_div_by_ws(offs, mtd)) *
    mtd_oobavail(mtd, ops)

While such overflow will certainly never happen due to the numbers
handled, it is cleaner to fix this operation anyway.

The problem is that all the maths include 32-bit quantities, while the
result is stored in an explicit 64-bit value.

As maxooblen will just be compared with a size_t, let's change the
type of the variable to a size_t. This will not fix anything but will
clarify a bit the situation. Then, do an explicit cast to fix Coverity
warning.

Addresses-Coverity-ID: 184180 ("Integer handling issues")
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

mtd_oobavail() returns either mtd->oovabail or mtd->oobsize. Both
values are unsigned 32-bit entities, so there is no reason to pretend
returning a signed one.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

Add Macronix MX66U2G45F flash device description.
This is a 256 MiB part.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Vignesh R <vigneshr@ti.com>
[jagan: use 'g' instead of 'f' in flash name]
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Since all DTS files has been switched to "jedec,spi-nor", remove
the "spi-flash" compatible from the bindings examples.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: NRick Chen <rick@andestech.com>
Reviewed-by: NPatrick Delaunay <Patrick.delaunay@st.com>
Reviewed-by: NJagan Teki <jagan@openedev.com>

Now the "spi-flash" compatible has been removed in the DTS files,
remove this compatible from sf_probe to finally use the Linux "jedec,spi-nor"
compatible.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: NJagan Teki <jagan@openedev.com>

The x86 code and DT uses "spi-flash" to detect a flash node, switch to
"jedec,spi-nor" in the DTS files and in fdtdec by switching the
GENERIC_SPI_FLASH value to to jedec,spi-nor.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: NJagan Teki <jagan@openedev.com>

There is no reason not to use the Linux "jedec,spi-nor" binding in U-Boot
dts files. This compatible has been added in sf_probe, let use it.

This patch switches to jedec,spi-nor when spi-flash is used in the DTS
and DTSI files, and removed spi-flash when jedec,spi-nor is already
present.

The x86 dts are switched in a separate commit since it depends on a change
in fdtdec.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Acked-by: NStefan Roese <sr@denx.de>
Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: NEvgeniy Paltsev <paltsev@synopsys.com>
Reviewed-by: NRick Chen <rick@andestech.com>
Reviewed-by: NPatrick Delaunay <Patrick.delaunay@st.com>
Reviewed-by: NJagan Teki <jagan@openedev.com>

Add support for SPANSION s25fl064l
Signed-off-by: NHeiko Schocher <hs@denx.de>
Reviewed-by: NJagan Teki <jagan@openedev.com>
Acked-by: NVignesh R <vigneshr@ti.com>

This patch sync's the U-Boot SPI NAND GigaDevice GD5F1GQ4UExxG support
with the latest Linux version (v5.0-rc3) plus the chip supported posted
on the MTD list. Only the currently in U-Boot available chip is
supported with this sync.

The changes for the GD5F1GQ4UExxG are:
- Name of NAND device changed to better reflect the real part
- OOB layout changed to only reserve 1 byte for BBT
- Use ECC caps 8bits/512bytes instead of 8bits/2048bytes
- Enhanced ecc_get_status() function to determine and report
  a more fine grained bit error status
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Boris Brezillon <bbrezillon@kernel.org>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: NJagan Teki <jagan@openedev.com>

Use quad write if SPI_TX_QUAD flag is set.

Tested quad write on Stratix 10 SoC board (Micron
serial NOR flash, mt25qu02g)
Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: NJagan Teki <jagan@openedev.com>

- Various rmobile fixes

- test.py tests for mmc
- ext4 symlink support and other fixes
- ext4 block group descriptor sizing

Currently enabling fsck on FAT16/FAT32 exposes that we have problems
with:
TestFsBasic.test_fs13[fat16]
TestFsBasic.test_fs11[fat32]
TestFsBasic.test_fs12[fat32]
TestFsBasic.test_fs13[fat32]
TestFsExt.test_fs_ext1[fat32]
TestFsExt.test_fs_ext2[fat32]
TestFsExt.test_fs_ext3[fat32]
TestFsExt.test_fs_ext4[fat32]
TestFsExt.test_fs_ext5[fat32]
TestFsExt.test_fs_ext6[fat32]
TestFsExt.test_fs_ext7[fat32]
TestFsExt.test_fs_ext8[fat32]
TestFsExt.test_fs_ext9[fat32]
TestMkdir.test_mkdir6[fat16]
TestMkdir.test_mkdir1[fat32]
TestMkdir.test_mkdir2[fat32]
TestMkdir.test_mkdir3[fat32]
TestMkdir.test_mkdir4[fat32]
TestMkdir.test_mkdir5[fat32]
TestMkdir.test_mkdir6[fat32]
TestUnlink.test_unlink1[fat16]
TestUnlink.test_unlink2[fat16]
TestUnlink.test_unlink3[fat16]
TestUnlink.test_unlink4[fat16]
TestUnlink.test_unlink5[fat16]
TestUnlink.test_unlink6[fat16]
TestUnlink.test_unlink7[fat16]
TestUnlink.test_unlink1[fat32]
TestUnlink.test_unlink2[fat32]
TestUnlink.test_unlink3[fat32]
TestUnlink.test_unlink4[fat32]
TestUnlink.test_unlink5[fat32]
TestUnlink.test_unlink6[fat32]
TestUnlink.test_unlink7[fat32]

This is because we don't update the "information sector" on FAT32.
While in the future we should resolve this problem and include that
feature, we should enable fsck for ext4 to ensure that things remain in
good shape there.
Signed-off-by: NTom Rini <trini@konsulko.com>

Ext4 allows for arbitrarily sized block group descriptors when 64-bit
addressing is enabled, which was previously not properly supported. This
patch dynamically allocates a chunk of memory of the correct size.
Signed-off-by: NBenjamin Lim <jarsp.ctf@gmail.com>

Add option to the mmc rd test to check the duration of the
execution of the mmc read command. This allows intercepting
read performance regressions.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Add test for 'mmc info' subcommand. This tests whether the card
information is obtained correctly and verifies the device, bus
speed, bus mode and bus width.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Add test for 'mmc rescan' subcommand. This tests whether the
system can switch to a specific card and then rescan the card.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Add separate test for 'mmc dev' subcommand. This tests whether
the system can switch to a specific card.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Factor out the 'mmc dev' call so it can be recycled by other tests.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>

A FAT12/FAT16 root directory location is specified by a sector offset and
it might not start at a cluster boundary. It also resides before the
data area (before cluster 2).

However, the current code assumes that the root directory is located at
a beginning of a cluster, causing no files to be found if that is not
the case.

Since the FAT12/FAT16 root directory is located before the data area
and is not aligned to clusters, using unsigned cluster numbers to refer
to the root directory does not work well (the "cluster number" may be
negative, and even allowing it be signed would not make it properly
aligned).

Modify the code to not use the normal cluster numbering when referring to
the root directory of FAT12/FAT16 and instead use a cluster-sized
offsets counted from the root directory start sector.

This is a relatively common case as at least the filesystem formatter on
Win7 seems to create such filesystems by default on 2GB USB sticks when
"FAT" is selected (cluster size 64 sectors, rootdir size 32 sectors,
rootdir starts at half a cluster before cluster 2).

dosfstools mkfs.vfat does not seem to create affected filesystems.
Signed-off-by: NAnssi Hannula <anssi.hannula@bitwise.fi>
Reviewed-by: NBernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Tested-by: NBernhard Messerklinger <bernhard.messerklinger@br-automation.com>

Hi,

when I try to load a sparse file via ext4load, I am getting the error message
'invalid extent'

After a deeper look in the code, it seems to be an issue in the function ext4fs_get_extent_block in fs/ext4/ext4_common.c:

The file starts with 1k of zeros. The blocksize is 1024. So the first extend block contains the following information:

eh_entries: 1
eh_depth: 1
ei_block 1

When the upper layer (ext4fs_read_file) asks for fileblock 0, we are running in the 'invalid extent' error message.
For me it seems, that the code is not prepared for handling a sparse block at the beginning of the file. The following change, solved my problem:

I am really not an expert in ext4 filesystems. Can somebody please have a look at this issue and give me a feedback, if I am totally wrong or not?

Test cases are:
1) basic link creation, verify it can be followed
2) chained links, verify it can be followed
3) replace exiting file a with a link, and a link with a link. verify it
   can be followed
4) create a broken link, verify it can't be followed
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

The command line is:
ln <interface> <dev[:part]> target linkname

Currently symbolic links are supported only in ext4 and only if the option
CMD_EXT4_WRITE is enabled.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Re-use the functions used to write/create a file, to support creation of a
symbolic link.
The difference with a regular file are small:
- The inode mode is flagged with S_IFLNK instead of S_IFREG
- The ext2_dirent's filetype is FILETYPE_SYMLINK instead of FILETYPE_REG
- Instead of storing the content of a file in allocated blocks, the path
to the target is stored. And if the target's path is short enough, no block
is allocated and the target's path is stored in ext2_inode.b.symlink

As with regulars files, if a file/symlink with the same name exits, it is
unlinked first and then re-created.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
[trini: Fix ext4 env code]
Signed-off-by: NTom Rini <trini@konsulko.com>

There is no need to modify the buffer passed to ext4fs_write_file().
The memset() call is not required here and was likely copied from the
equivalent part of the ext4fs_read_file() function where we do need it.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

We need to make sure that file writes,file creation, etc. are properly
performed and do not corrupt the filesystem.
To help with this, introduce the assert_fs_integrity() function that
executes the appropriate fsck tool. It should be called at the end of any
test that modify the content/organization of the filesystem.
Currently only supports FATs and EXT4.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

If the metadata checksums are enabled, all write operations will fail.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

When a file contains extents, U-Boot currently reads extent-related data
for each block in the file, even if that data is located in the same
block each time. This significantly slows down loading of files that use
extents. Implement a very dumb cache to prevent repeatedly reading the
same block. Files with extents now load as fast as files without.

Note: There are many cases where read_allocated_block() is called. This
patch only addresses one of those places; all others still read redundant
data in any case they did before. This is a minimal patch to fix the
load command; other cases aren't fixed.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

v2018.01 commit e23eb942 ("ARM: rmobile: Stop using
rcar-common/common.c on Gen3") removed
board/renesas/rcar-common/common.c from the build chain with the
reasoning that calling arch_preboot_os() is no longer needed.

However, it left the arch_preboot_os() in place. Get rid of it.
This is done in preparation of resurrecting rcar-common/common.c.

NOTE: The three removed header includes (io.h, sys_proto.h, rcar-mstp.h)
are in direct relationship with the dropped arch_preboot_os() hook. The
other headers (common.h, rmobile.h) are going to be needed by pretty
much anything that is going to appear in the rcar common code. So, keep
the two in place.
Signed-off-by: NEugeniu Rosca <erosca@de.adit-jv.com>

The E2 Alt board has two USB ports, add missing DT nodes to make the
USB available.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Increase the USB power good delay on Alt, this is required with
certain USB sticks, otherwise they might not be detected.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Reset and initialize the PHY once in the probe() function rather than
doing it over and over again is start() function. This requires us to
keep the clock enabled while the driver is in use. This significantly
reduces the time between transfers as the PHY doesn't have to restart
autonegotiation between transfers, which takes forever.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>

Synchronize R-Car Gen3 device trees with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>

Synchronize R-Car Gen2 device trees with Linux 5.0,
commit 1c163f4c7b3f621efff9b28a47abb36f7378d783 .
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>