- 28 11月, 2009 1 次提交
-
-
由 Nishanth Menon 提交于
Micron DDR timings based on: http://www.sakoman.net/cgi-bin/gitweb.cgi?p=x-load-omap3.git;a=blob;f=include/asm/arch-omap3/mem.h;h=e6fbfe3947f5d0d85fea776e30821d4017316d86;hb=HEAD Introduce Micron DDR timings and provide CONFIG_OMAP3_INFINEON_DDR and CONFIG_OMAP3_MICRON_DDR config options to allow for platform files to setup their timings as per the type of DDR selected Reported-by: Steve Sakoman in http://www.nabble.com/forum/Permalink.jtp?root=25779518&post=25959734&page=ySigned-off-by: NNishanth Menon <nm@ti.com>
-
- 19 10月, 2009 1 次提交
-
-
由 Sandeep Paulraj 提交于
This patch removes dependency on the sizes.h header file and removes all references to SZ_xx. Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 13 10月, 2009 1 次提交
-
-
由 Tom Rix 提交于
This changes fixes an early i2c error. It appears that I2C is working because once a read or write error is detected, the omap24xx_i2c driver calls i2c_init inside its error handling check. While it is ok to attempt error handling this way, the boards must not depend on this side effect to initialize it's i2c. Instead of explicitly calling i2c_init for every board, use the generic arm initialization in lib_arm/board.c. By defining the config variable CONFIG_HARD_I2C, the omap3 i2c initialization is included in the init_sequence table. Run tested on Beagle. Compile tested on the omap3's Signed-off-by: NTom Rix <Tom.Rix@windriver.com> Acked-by: NDirk Behme <dirk.behme@googlemail.com>
-
- 05 9月, 2009 1 次提交
-
-
由 Frederik Kriewitz 提交于
This patch adds support for the DevKit8000 board. Signed-off-by: NFrederik Kriewitz <frederik@kriewitz.eu>
-
- 08 8月, 2009 2 次提交
-
-
由 Dirk Behme 提交于
Signed-off-by: NMatthias Ludwig <mludwig@ultratronik.de> Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Matthias Ludwig 提交于
Embedd chip select configuration into struct for gpmc config instead of having it completely separated as suggested by Wolfgang Denk on http://lists.denx.de/pipermail/u-boot/2009-May/052247.htmlSigned-off-by: NMatthias Ludwig <mludwig@ultratronik.de>
-
- 29 7月, 2009 1 次提交
-
-
由 Tom Rix 提交于
Because twl4030 now has its own device files, move exiting omap3 power_init_r to a new location. power_init_r is the only function in board/omap3/common. It initializes the twl4030 power for the board and enables the led. The power part of the the function is moved to twl4030_power_init in drivers/power/twl4030.c The power compilation is conditional on the existing config variable CONFIG_TWL4030_POWER. The led part is moved to twl4030_led_init in the new file drivers/misc/twl4030_led.c The led compilation is conditional on the new config variable CONFIG_TWL4030_LED The directory board/omap3/common was removed because power_init_r was the only function in it. Signed-off-by: NTom Rix <Tom.Rix@windriver.com> Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NHeiko Schocher <hs@denx.de>
-
- 19 7月, 2009 1 次提交
-
-
由 Wolfgang Denk 提交于
Commit 8d2effea added a warning for configurations that use NAND without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but failed to fix the affected boards. This patch covers the non-PPC boards that were missed in the previous patch (commit 170c1972). Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 13 6月, 2009 1 次提交
-
-
由 Stefan Roese 提交于
By changing the cmd_mtdparts to only use the MTD infrastructure and not the direct interface to the CFI NOR FLASH driver we now need to add the MTD infrastructure to all boards using those mtdparts commands. This patch adds those components: CONFIG_MTD_DEVICE (for all FLASH types) plus CONFIG_FLASH_CFI_MTD (for NOR FLASH) To all board maintainers: Please test this on your platforms and report any problems/issues found. Thanks. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Wolfgang Denk <wd@denx.de> Cc: Ron Madrid <info@sheldoninst.com> Cc: Georg Schardt <schardt@team-ctech.de> Cc: Michal Simek <monstr@monstr.eu> Cc: Ladislav Michl <ladis@linux-mips.org> Cc: Martin Krause <martin.krause@tqs.de> Cc: Gary Jennejohn <garyj@denx.de> Cc: Ricardo Ribalda <ricardo.ribalda@uam.es>
-
- 01 5月, 2009 1 次提交
-
-
由 Manikandan Pillai 提交于
Signed-off-by: NDirk Behme <dirk.behme@googlemail.com> Signed-off-by: NManikandan Pillai <mani.pillai@ti.com>
-
- 30 4月, 2009 2 次提交
-
-
由 Dirk Behme 提交于
Remove remaining legacy NAND defines for Beagle, EVM, Overo and Pandora. Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
由 Sanjeev Premi 提交于
Use the functions print_cpuinfo() and checkboard() to display the cpu and board specific information. These functions reuse content from the existing function display_board_info() - which has been removed. Also, updated the existig OMAP3 configurations to define: - CONFIG_DISPLAY_CPUINFO - CONFIG_DISPLAY_BOARDINFO Signed-off-by: NSanjeev Premi <premi@ti.com>
-
- 27 4月, 2009 1 次提交
-
-
由 Dirk Behme 提交于
In recent U-Boot mmcinit changed to mmc init. Signed-off-by: NSteve Sakoman <steve@sakoman.com> Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-
- 04 4月, 2009 1 次提交
-
-
由 Wolfgang Denk 提交于
According to the doc/feature-removal-schedule.txt, the "autoscr" command will be replaced by the "source" command in approximately 6 months from now. This patch prepares this change and starts a 6 month transition period as follows: - The new "source" command has been added, which implements exactly the same functionlaity as the old "autoscr" command before - The old "autoscr" command name is kept as an alias for compatibility - Command sequences, script files atc. have been adapted to use the new "source" command - Related environment variables ("autoscript", "autoscript_uname") have *not* been adapted yet; these will be renamed resp. removed in a separate patch when the support for the "autoscr" command get's finally dropped. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 31 3月, 2009 1 次提交
-
-
由 Ladislav Michl 提交于
Divisor field is called PTV not PVT. Signed-off-by: NLadislav Michl <ladis@linux-mips.org> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 29 3月, 2009 1 次提交
-
-
由 Ladislav Michl 提交于
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
-
- 26 3月, 2009 1 次提交
-
-
由 Nishanth Menon 提交于
http://www.denx.de/wiki/DULG/UBootCmdGroupFlash#UBootCmdFlMtdparts provides a flexible way to create and maintain u-boot mtd partitions. This allows commands such as "nand erase fs" to work and the user no longer needs to decode the absolute nand offsets. This patch enables this function for beagleboard Signed-off-by: NNishanth Menon <nm@ti.com> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
- 29 1月, 2009 1 次提交
-
-
由 Dirk Behme 提交于
Add BeagleBoard support, common power code and README. Signed-off-by: NJason Kridner <jkridner@beagleboard.org> Signed-off-by: NDirk Behme <dirk.behme@googlemail.com>
-