Since wfi instruction is only available on ARMv7, add a conditional
macro for it.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>

Set ETM TRCLK down to 78MHz to get clear wave form.
This patch makes difference only when you use ETM trace connecting JTAG debugger.
Signed-off-by: NTetsuyuki Kobayashi <koba@kmckk.co.jp>
Acked-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

After stress test, I found some of kzm9g board occures memory failure.
This patch adust SDRAM setting.
- Enlarge drivability on both SDRAM controller and SDRAM itself
- Raise core voltage
Signed-off-by: NTetsuyuki Kobayashi <koba@kmckk.co.jp>
Acked-by: NNobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>

The following features are supported:
 * 128 MB DDR1 SDRAM
 * DUART
 * SD/MMC Card Socket
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Tested-by: NFabio Estevam <fabio.estevam@freescale.com>

This adds a default environment with support for MMC booting.
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>

Add support for the MMC attached to SSP1.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

The MX23 has different layout of DMA channels. Fix the MMC
driver to support MX23.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

Some MXS based boards do not implement the card-detect signal. Allow
user to specify alternate card-detect implementation.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

This does the same reset mask as done in v3.7 Linux kernel code.
The block is properly configured for MMC operation that way.
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

The MX23 SSP register layout differs from MX28 in certain bits,
adjust the register layout accordingly.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

The MX23 has less channels for the APBH DMA, sligtly different register
layout and some bits in those registers are placed differently. Reflect
this in the driver. This patch fixes MMC/DMA issue on MX23.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

This allows us to create the phydev before calling
fec_probe in later patch.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

This allows us to create the phydev before calling
fec_probe in later patch.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

It is useful to be able to try a range of
possible phy addresses to connect.

Also, an ethernet device is not required
to use phy_find_by_mask leading to better
separation of mii vs ethernet, as suggested
by Andy Fleming.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

Having only one call to fec_probe will ease the changing of its
parameters.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

Only the hardware ethernet registers are needed
for this function, so don't pass the more general
structure. I'm trying to separate MII and fec.

This also fixes MX28 fec_mii_setspeed use on secondary ethernet port

This was found by inspection of the code and should be
checked on real hardware.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

It is more logical to test for CONFIG_FEC_MXC_PHYADDR
to determine whether to define the function fecmxc_initialize.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

Using the __weak annotation can make the code cleaner.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NMarek Vasut <marex@denx.de>

Since this structure is not i.MX5x specific, remove the '5x' to make it more
generic.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

commit 49ea0ff5 (49ea0ff5) introduced CONFIG_SYS_MMC_ENV_PART into mx6qsabresd.h
to store the mmc partition, but in order for it to have effect we should place
it into 'mmcpart' variable.

Also add CONFIG_SYS_MMC_ENV_PART into mx6qsabreauto.h.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

The USB host interface is routed to plug USB1/J30 on the mother board.
Signed-off-by: NKnut Wohlrab <knut.wohlrab@de.bosch.com>

The memory power supply on MX23 didn't pump out enough juice into
the DRAM chip, thus caused occasional memory corruption. Fix this.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: NOtavio Salvador <otavio@ossystems.com.br>

The '#' used as comments in the files cause the preprocessor
trouble, so change to /* */.

The mkimage command which uses this preprocessor output
was moved to arch/arm/imx-common/Makefile

.gitignore was updated to ignore .cfgtmp files.
Signed-off-by: NTroy Kisky <troy.kisky@boundarydevices.com>

The MX23 has different handling of the SSP clock and GPMI NAND clock sources,
add necessary quirks into the clock code to properly handle these.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

Set Write Protection GPIO as input.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>

This patch adds support for MX23-based Olinuxino board.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>

Replace use of ttyAM0 with ttyAMA0 as default serial console.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

The memory init is slightly different on MX23, thus split the memory
init for mx23 and mx28 into different functions.
Signed-off-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>

The power block on MX23 must first be ungated before it can be operated.
Add function to MXS power init that ungates it.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>

The MX23 can only use two SSP ports.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Andy Fleming <afleming@freescale.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>

Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

For i.MX23 we need to pass imx23 as elftosb param.
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

This adds the boot mode support for i.MX23 processors.
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>

Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>

Add information to identify i.MX23 chips and its known revisions.
Signed-off-by: NOtavio Salvador <otavio@ossystems.com.br>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>