Without the prefix, "same-as-spl" in `u-boot,spl-boot-order` will not work
as expected. When board_boot_order() `spl-boot-order.c` meets
"same-as-spl", it gets the conf by looking the boot_devices table by boot
source, and parse the node by the conf with:

   node = fdt_path_offset(blob, conf);

which will failed without the "/" indicating the path.

Currently only entries of boot_devices in rk3399 have the "/" prefix.
Therefore add the missing ones in other boards.
Signed-off-by: NLevin Du <djw@t-chip.com.cn>
Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Use the same SPL_STACK_R_ADDR in Kconfig instead of each board config;
default to 0x4000000(64MB) instead of 0x80000(512KB) for this address
can support all the SoCs including those may have only 64MB memory, and
also reserve enough space for atf, kernel(in falcon mode) loading.

After the ATF entry move to 0x40000, the stack from 0x80000 may be override
when loading ATF bl31.
Signed-off-by: NKever Yang <kever.yang@rock-chips.com>

A trusted execution environment should also get loaded as loadable from
a fit image, so add the possibility to present a tee.elf to make_fit_atf.py
that then gets included as additional loadable into the generated its.

For ease of integration the additional loadable is created as atf_(x+1)
after all others to re-use core generation loops.

Tested against the combinations of 1-part-atf and multi-part-atf each
time with and without a tee binary present.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

rk3328 can use same-as-spl option so next loaders are loaded from the same
medium.
Add the boot order in the rock64 dts otherwise booting from sdcard
will result in u-boot looking into the eMMC.
Signed-off-by: NEmmanuel Vadot <manu@freebsd.org>
Reviewed-by: NPeter Robinson <pbrobinson@gmail.com>
Tested-by: NPeter Robinson <pbrobinson@gmail.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Add a call to rk3328_configure_cpu() during initialization to set the
CPU-clock frequency.
Signed-off-by: NSimon South <simon@simonsouth.net>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Specification
- Rockchip RK3399
- LPDDR4
- TF sd scard slot
- eMMC
- M.2 B-Key for 4G LTE
- AP6256 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- TYPE-C Power supply

Commit details of rk3399-leez-p710.dts sync from linus tree for Linux 5.4-rc1:
"arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC"
(sha1: 	fc702ed49a8668a17343811ee28214d845bfc5e6)
Signed-off-by: NAndy Yan <andyshrk@gmail.com>
Reviewed-by: NKever Yang <kever.yang@rock-chips.com>

Add subcommand for add writing BCB only, where we provide appropriate
offsets for firmware1 and firmware2 and size.

Example of usage:
> nandbcb bcbonly 0x00180000 0x00080000 0x00200000
Writing 1024 bytes to 0x0: randomizing
OK
Writing 1024 bytes to 0x20000: randomizing
OK
Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: NMax Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com>

Move code for writing FCB/DBBT pages to a separate function
Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: NMax Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com>

Add support for updating FCB/DBBT on i.MX7:
- additional new fields in FCB structure
- Leverage hardware BCH/randomizer for writing FCB
Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: NMax Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com>

Extend GPMI Integrated ECC Control Register Description, include
additional defines for enabling randomizer function and providing
proper randomizer type.

For additional details check i.MX7 APR, section
9.6.6.3 GPMI Integrated ECC Control Register Description
(GPMI_ECCCTRLn)
Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com>
Tested-by: NMax Krummenacher <max.krummenacher@toradex.com>
Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com>

Add i.MX8QM ROM 7720a1 board support

Boot log as below:
U-Boot 2019.10-rc3-00004-gd073e0242f (Sep 20 2019 - 08:24:13 +0200)

CPU:   NXP i.MX8QM RevB A53 at 1200 MHz

Model: Advantech iMX8QM Qseven series
Board: ROM-7720-A1 4GB
Build: SCFW 65afe5f6
Boot:  SD2
DRAM:  4 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In:    serial@5a060000
Out:   serial@5a060000
Err:   serial@5a060000
Net:   eth0: ethernet@5b040000Could not get PHY for FEC1: addr 1
, eth-1: ethernet@5b050000
Hit any key to stop autoboot:  0
Signed-off-by: NOliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>

Sync dts for i.MX8MM from Linux Kernel 5.4.0-rc1
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

This commit adds support for the brppt2 board. The board is based on the
i.mx6 dual-lite SoC.
Signed-off-by: NHannes Schmelzer <hannes.schmelzer@br-automation.com>

Borrow ID reading code from Ye Li (NXP U-Boot, commit ID 5b443e3e2617)
but drop imx-mkimage commit ID reading since we now use in tree mkimage.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>

Need to pass total 5 arguments for SIP HAB call on i.MX8MQ,
so update the interface to add new argument.
Signed-off-by: NYe Li <ye.li@nxp.com>
[agust: fixed imx8m-power-domain build]
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Reviewed-by: NPatrick Wildt <patrick@blueri.se>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>

Add function and new command "auth_cntr" for secure boot support.
When booting with life cycle set to OEM closed, we need to use
this function to authenticate the OS container and load kernel & FDT
from OS container to their destination.

Also add image authentication call when loading container images.

Users can set CONFIG_AHAB_BOOT=y to enable the feature. It is not
set at default.
Signed-off-by: NYe Li <ye.li@nxp.com>
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Enable bd71837 pmic for i.MX8MM EVK board, need to set voltage for
DRAM and linux suspend voltage requirement.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

It will be easy to separate SD/EMMC when booting in SPL stage, then
no need to bother which device is BOOT_DEVICE_MMC1/2.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Add init_nand_clk to enable gpmi nand clock. Since i.MX8MQ not use CCF,
so we still use legacy mode to configure the clock.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Improve the IRQ response latency by setting GIC root clock source to
sys_pll2_200m from osc.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

The i.MX8MQ B1 uses OCOTP_HW_OCOTP_READ_FUSE_DATA register for chip id.
It returns a magic number 0xff0055aa. update get_cpu_rev to support it,
and enable ocotp clock to access ocotp.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Migrate to DM_VIDEO, update the device tree and remove code that is no
longer necessary.
Reviewed-by: NPeng Fan <peng.fan@nxp.com>
Signed-off-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>

Migrate to DM_ETH and remove code that is no longer necessary.
Reviewed-by: NPeng Fan <peng.fan@nxp.com>
Signed-off-by: NSébastien Szymanski <sebastien.szymanski@armadeus.com>

This updates the i.MX8MQ device trees and, necessarily, also the
i.MX8MQ clock bindings.  These are taken verbatim from from the
Linux kernel version v5.4-rc2, which three small changes which
were already part of the previous device tree:

 * Keep the PSCI reserved memory range
 * Keep the alias for ethernet, so that the MAC address can be set
 * Keep the modified #include for the IOMUXC pins
Signed-off-by: NPatrick Wildt <patrick@blueri.se>
Acked-by: NPeng Fan <peng.fan@nxp.com>

This commit converts mccmon6's u-boot proper (in a single commit to avoid
build breaks) to use solely DM/DTS.

The DTS description of the mccmon6 has been ported from Linux kernel
(v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be)
Signed-off-by: NLukasz Majewski <lukma@denx.de>

The TPC70 is equipped with DS1307 RTC device. Add code to enable support
for it.
Signed-off-by: NLukasz Majewski <lukma@denx.de>

Add u-boot,dm-pre-reloc properties for uart pinmux configuration
nodes, which enables UART as early as possible (before relocation).

Without this we miss almost the half of output (U-boot version,
CPU defails, Reset cause, DRAM details etc.).

Fixes: cd69e8ef ("colibri-imx6ull: migrate pinctrl and regulators to dtb/dm")
Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com>

Introduce imx6ull-colibri-u-boot.dtsi for u-boot specific properties to
keep original imx6ull-colibri.dts in sync with Linux.

Move all contents of imx6ull-colibri.dts to imx6ull-colibri.dtsi +
additionally fix checkpatch warnings.
Reviewed-by: NOleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com>

According to IMX28CEC rev. 4, 10/2018, Table 15. Recommended Operating
Conditions, page 16, the VDDD should be set to 1.55V when the CPU is
operating at 454MHz. This is the case in U-Boot, hence increase the
VDDD voltage. This fixes instability when performing TFTP transfers.
Increase the brownout threshold to 1.4V. The documentation recommends
1.45V setting for the brownout, however, this triggers failure during
power block init, so keep the brownout slightly lower.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: NFabio Estevam <festevam@gmail.com>

Signed-off-by: NClaudius Heine <ch@denx.de>

imx6_is_bmode_from_gpr9 always returns false, because
IMX6_SRC_GPR10_BMODE is 1<<28 and gets casted to u8 on return.

This moves the function body into imx6_src_get_boot_mode, since that is the
only one using it and it is on the same abstraction level (accessing
registers directly).
Signed-off-by: NClaudius Heine <ch@denx.de>

Add devicetree support for iMXQXP AI_ML board from Einfochips.
Signed-off-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>

Firmware Configuration Block(FCB) for imx6ul(l) needs to be
BCH encoded.
Signed-off-by: NParthiban Nallathambi <pn@denx.de>
Acked-by: NShyam Saini <shyam.saini@amarulasolutions.com>
Acked-by: NPeng Fan <peng.fan@nxp.com>

Synchronize CPSW/MDIO/PHY DT nodes with latest linux - replace deprecated
phy_id property with phy-handle.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Felix Brack <fb@ltec.ch>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>

Synchronize CPSW/MDIO/PHY DT nodes with latest linux - replace deprecated
phy_id property with phy-handle.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>

Synchronize CPSW/MDIO/PHY DT nodes with latest linux - replace deprecated
phy_id property with phy-handle.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>

Introduce disable_ipu_clock(). This is done in preparation for
configuring the NoC registers on i.MX6QP in SPL.

Afer the NoC registers are set the IPU clocks can be disabled.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>

The code can be made simpler by using setbits_le32(), so switch
to it.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>

We already a message indicating that U-Boot is about to jump to SPL, so
make this one a debug() to reduce code size.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

We don't need to do this and it is done (in more detail) in U-Boot proper.
Drop this to save code space.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>