Enable CONFIG_NVME and CONFIG_CMD_NVME for Layerscape
platforms
Signed-off-by: NWasim Khan <wasim.khan@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

CONFIG_ENV_OVERWRITE disables write protection on various environment
variables like "ethaddr" and "serial".

Enable this config in LS1046A and LS1012A defconfigs. This resolves an
error while setting multiple values of "ethaddr" variable.

Before the change:
=> setenv ethaddr 00:E0:0C:00:06:0
=> setenv ethaddr 00:E0:0C:00:06:1
Error: Can't overwrite "ethaddr"
Error inserting "ethaddr" variable, errno=1

After the change:
=> setenv ethaddr 00:E0:0C:00:06:0
=> setenv ethaddr 00:E0:0C:00:06:1
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Add Root Complex and Endpoint mode specific config entries, such that
it's feasible to enable the RC and/or EP mode driver indepently.
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

This converts the following to Kconfig:
   CONFIG_CMD_ASKENV
   CONFIG_CMD_BMP
   CONFIG_CMD_BOOTD
   CONFIG_CMD_CACHE
   CONFIG_CMD_CRC32
   CONFIG_CMD_DHCP
   CONFIG_CMD_ENV
   CONFIG_CMD_EXPORTENV
   CONFIG_CMD_EXT2
   CONFIG_CMD_EXT4
   CONFIG_CMD_FLASH
   CONFIG_CMD_FS_GENERIC
   CONFIG_CMD_FUSE
   CONFIG_CMD_GPIO
   CONFIG_CMD_GPT
   CONFIG_CMD_GREPENV
   CONFIG_CMD_I2C
   CONFIG_CMD_IMLS
   CONFIG_CMD_IMPORTENV
   CONFIG_CMD_LOADB
   CONFIG_CMD_LOADS
   CONFIG_CMD_MEMINFO
   CONFIG_CMD_MII
   CONFIG_CMD_MTDPARTS
   CONFIG_CMD_NAND
   CONFIG_CMD_NAND_TRIMFFS
   CONFIG_CMD_NFS
   CONFIG_CMD_PCA953X
   CONFIG_CMD_PCA953X_INFO
   CONFIG_CMD_PCI
   CONFIG_CMD_PING
   CONFIG_CMD_READ
   CONFIG_CMD_SF
   CONFIG_CMD_SPI
   CONFIG_CMD_SPL
   CONFIG_CMD_SPL_WRITE_SIZE
   CONFIG_CMD_TIME
   CONFIG_CMD_TRACE
   CONFIG_CMD_UBI
   CONFIG_CMD_UBIFS
   CONFIG_CMD_UNZIP
   CONFIG_FS_EXT4
Signed-off-by: NTom Rini <trini@konsulko.com>

All LS1012A board variants have same CONFIG_ENV_SECT_SIZE and
CONFIG_ENV_SIZE values. If both config values are same, flash
environment cannot be saved. Since, CONFIG_ENV_SECT_SIZE needs to be
same as that of flash sector size, this entry cannot be changed.
Reduce CONFIG_ENV_SIZE value to 0x2000. This also helps in making config
value aligned with other boards environemt size.
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Signed-off-by: NAshish Kumar <Ashish.kumar@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Since CONFIG_FSL_QSPI is already enabled for LS1012A in defconfigs. Also
enable CONFIG_SPI_FLASH_SPANSION for LS1012A boards having spansion
flashes.
Signed-off-by: NAshish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>

Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

With DM_USB enabled, enable CONFIG_BLK to remove this
compile warning for ls1012afrdm based targets:

===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: NRan Wang <ran.wang_1@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1012A
Signed-off-by: NBiwen Li <biwen.li@nxp.com>
Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

MTD must be enabled when there is a SPI NOR flash using the
SPI_FLASH_MTD config entry.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: NBoris Brezillon <boris.brezillon@bootlin.com>

- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Signed-off-by: NAshish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
  CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
  2), set this to 8.
Signed-off-by: NTom Rini <trini@konsulko.com>

4K erase size is used only in case of hydrid mode which is not
supported on any NXP platform with flash "s25fs512s".
Supported mode is uniform sector, with erase size 256kiB.
Signed-off-by: NAshish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

This converts the following to Kconfig:
   CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver.  For now, just update
the CONFIG tests.  This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig.
Signed-off-by: NMario Six <mario.six@gdsys.cc>
[trini: Re-run migration]
Signed-off-by: NTom Rini <trini@konsulko.com>

Migrate the CONFIG_SYS_ALT_MEMTEST option to Kconfig.
Signed-off-by: NMario Six <mario.six@gdsys.cc>
[trini: Re-run migration after also including CMD_MEMTEST]
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Add configurations for PFE.
Signed-off-by: NCalvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: NAnjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set.  This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Include common config_distro_defaults.h and config_distro_bootcmd.h
for u-boot enviroments to support automatical distro boot which
scan boot.scr from external storage devices(e.g. SD and USB)
and execute autoboot script.
Signed-off-by: NBhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: NRajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: NYork Sun <york.sun@nxp.com>

The option is specified in Kconfig, but still a few config header files
are overriding the choice by #undef'ing it. Re-sync the option with
moveconfig to rid of the #undefs.
Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
   i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.
Signed-off-by: NTuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_ENV_IS_IN_SPI_FLASH
Signed-off-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NTom Rini <trini@konsulko.com>