- 19 1月, 2011 3 次提交
-
-
由 Nobuhiro Iwamatsu 提交于
There is not break character between board name and CPU. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Heiko Schocher 提交于
difference to previous board version: - M29W128GH flash from Numonyx - SDRAM ISSI IS45S16800 (Option A2 105°C) - rev5 uses RTC RV-3029-C2 - update cs0 and cs1 baseaddr and length depending on the detected flash size. - added Werner Pfister <Pfister_Werner@intercontrol.de> as maintainer for the digsy board variants - As the M29W128GH needs a special flash_cmd_reset() document that in the new file doc/README.cfi. - move "#endif /* CONFIG_CMD_IDE */" to the right place - remove LOWBOOT config option for digsy_mtc and digsy_mtc_rev5 boards - change doc/README.cfi as Stefan Roese suggested Signed-off-by: NHeiko Schocher <hs@denx.de> Signed-off-by: NStefan Roese <sr@denx.de> Acked-by: NDetlev Zundel <dzu@denx.de> cc: Wolfgang Denk <hs@denx.de> cc: Stefan Roese <sr@denx.de> cc: Werner Pfister <Pfister_Werner@intercontrol.de> cc: Detlev Zundel <dzu@denx.de>
-
由 Holger Brunck 提交于
The MPC852 based mgsuvd and kmsupx4 boards from keymile were initially ported but later on not developed further. So the respective files were removed to avoid unneeded merging and maintenance. Signed-off-by: NHolger Brunck <holger.brunck@keymile.com> Acked-by: Heiko Schocher<hs@denx.de>
-
- 14 1月, 2011 4 次提交
-
-
由 Kumar Gala 提交于
Mimic support that exists on MPC8536DS on the MPC8572DS to allow booting from NAND. Signed-off-by: NJin Qing <b24347@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
The PM854/PM856 boards are no longer maintained and thus we are removing support for them. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Acked-by: NWolfgang Denk <wd@denx.de>
-
由 Kumar Gala 提交于
The MPC8540EVAL board is no longer maintained and thus we are removing support for it. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Kumar Gala 提交于
The ATUM8548 board is no longer maintained and thus we are removing support for it. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 11 1月, 2011 1 次提交
-
-
由 Nobuhiro Iwamatsu 提交于
This adds support for the SHMIN SH7706 board(T-SH7706LAN). The CPU of this board is SH7706. There are SDRAM of 32M byte, Flash memory of 512K byte, Serial, 10Base Ether and MMC. http://web.kyoto-inet.or.jp/people/takagaki/T-SH7706/T-SH7706.htmSigned-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
- 17 12月, 2010 3 次提交
-
-
由 Ricardo Ribalda Delgado 提交于
Use common ppc4xx linker script for xilinx ppc440 and ppc405 related boards. Signed-off-by: NRicardo Ribalda Delgado <ricardo.ribalda@gmail.com> Signed-off-by: NStefan Roese <sr@denx.de>
-
由 Prafulla Wadaskar 提交于
Aspenite is a Development Board for ASPEN/ARMADA168(88AP168) with * Processor upto 1.2GHz * Parallel 1Gb x8 DDR2-1066 MHz * 16 Mb x16 NOR, 4Gb x8 SLC NAND, footprint for SPI NOR * Footprints for eMMC/eSD NAND & MMC x8 card * 4-in-1 card reader (xD, MMC/SD/MS Pro), CF True IDE socket * SEAF memory board, subset of PISMO2 With Peripherals: * 4.3” WVGA 24-bit LCD * Audio codecs (AC97 & I2S), TSI * VGA camera * Video in via 3 RCA jacks, and HDMI type C out * Marvell 88W8688 802.11bg/BT module * GPS RF IC * Dual analog mics & speakers, headset jack, LED, ambient light sensor * USB2.0 HS host (A), OTG (micro AB) * FE PHY, PCIE Mini Card slot * GPIO, GPIO expander with DIP switches for easier selection UART serial over USB, CIR This patch adds basic board support with DRAM and UART functionality The patch is tested for boot from DRAM using XDB Signed-off-by: NMahavir Jain <mjain@marvell.com> Signed-off-by: NPrafulla Wadaskar <prafulla@marvell.com>
-
由 Heiko Schocher 提交于
- serial console in PSC1 - 128MiB DRAM - 32MiB Flash - FEC Ethernet - 2 I2C busses - FPGA on CS3 - IDE - VGA SMI501 Signed-off-by: NHeiko Schocher <hs@denx.de> Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 09 12月, 2010 2 次提交
-
-
由 Stefano Babic 提交于
This board uses the OMAP-L138 SOM stacked on a custom baseboard. It supports SPI Flash, Ethernet with RMII. Signed-off-by: NStefano Babic <sbabic@denx.de> Signed-off-by: NBen Gardiner <bengardiner@nanometrics.ca> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sughosh Ganu 提交于
The patch adds basic board support for TI's OMAP-L138 based Hawkboard. This board is pretty similar to the da850 EVM. Support for nand and network access is added in this version. The following bootup procedure is used. At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand controllers and copies the second stage bootloader(nand_spl) to RAM. The secondary bootloader then copies u-boot from a predefined location in the nand flash to the RAM, and passes control to the u-boot image. Three config options are supported * hawkboard_config - Used to create the u-boot.bin. Tftp the u-boot.bin image to the RAM from u-boot, and flash to the nand flash at address 0xe0000. * hawkboard_nand_config - Used to generate the secondary bootloader(nand_spl) image. This creates an elf file u-boot-spl under nand_spl/. Create an AIS signed image using this file, and flash it to the nand flash at address 0x20000. The ais file should fit in one block. * hawkboard_uart_config - This is same as the first image, but with the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS Signed-off-by: NSughosh Ganu <urwithsughosh@gmail.com> Signed-off-by: NBen Gardiner <bengardiner@nanometrics.ca> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 08 12月, 2010 1 次提交
-
-
由 Andreas Bießmann 提交于
This patch also removes now unnecessary config.mk in board directory and make usage of new features in boards.cfg. Signed-off-by: NAndreas Bießmann <andreas.devel@googlemail.com>
-
- 07 12月, 2010 2 次提交
-
-
由 Reinhard Meyer 提交于
Adds support for the EMK TOP9000 CPU Module which is based on ATMELs ARM926EJS AT91SAM9XE SoC. Signed-off-by: NReinhard Meyer <u-boot@emk-elektronik.de>
-
由 Scott Wood 提交于
This patch http://patchwork.ozlabs.org/patch/72962/ included a boards.cfg change, but it was omitted when applied as f1c574d4 This fixes the NAND SPL build on MPC8315ERDB. Signed-off-by: NScott Wood <scottwood@freescale.com>
-
- 01 12月, 2010 2 次提交
-
-
由 Stefano Babic 提交于
This board uses the OMAP-L138 SOM stacked on a custom baseboard. It supports SPI Flash, Ethernet with RMII. Signed-off-by: NStefano Babic <sbabic@denx.de> Signed-off-by: NBen Gardiner <bengardiner@nanometrics.ca> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
由 Sughosh Ganu 提交于
The patch adds basic board support for TI's OMAP-L138 based Hawkboard. This board is pretty similar to the da850 EVM. Support for nand and network access is added in this version. The following bootup procedure is used. At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand controllers and copies the second stage bootloader(nand_spl) to RAM. The secondary bootloader then copies u-boot from a predefined location in the nand flash to the RAM, and passes control to the u-boot image. Three config options are supported * hawkboard_config - Used to create the u-boot.bin. Tftp the u-boot.bin image to the RAM from u-boot, and flash to the nand flash at address 0xe0000. * hawkboard_nand_config - Used to generate the secondary bootloader(nand_spl) image. This creates an elf file u-boot-spl under nand_spl/. Create an AIS signed image using this file, and flash it to the nand flash at address 0x20000. The ais file should fit in one block. * hawkboard_uart_config - This is same as the first image, but with the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS Signed-off-by: NSughosh Ganu <urwithsughosh@gmail.com> Signed-off-by: NBen Gardiner <bengardiner@nanometrics.ca> Signed-off-by: NSandeep Paulraj <s-paulraj@ti.com>
-
- 28 11月, 2010 1 次提交
-
-
由 Eric Cooper 提交于
update suggested sort command in comment to produce desired order suggest use of "column -t" to reformat Signed-off-by: NEric Cooper <ecc@cmu.edu>
-
- 27 11月, 2010 3 次提交
-
-
由 Wolfgang Denk 提交于
The barco board appears to be unmaintained since it was added about 5 years ago. The environment location has probably never been correct. Drop it. Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Marc Leeman <marc.leeman@barco.com> Acked-by: NStefan Roese <sr@denx.de>
-
由 Wolfgang Denk 提交于
The ERIC board appears to be unmaintained for more than 9 years. The environment location has probably never been correct, and has been definitely broken since for at least a year. Drop it. Signed-off-by: NWolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Swen Anderson <sand@peppercon.de> Acked-by: NStefan Roese <sr@denx.de>
-
由 Eric Cooper 提交于
start with sheevaplug configuration add modifications by Alexander Holler <holler@ahsoftware.de> change RAM definitions to one bank (128 MB) change ident string and prompt define MTD partitions and default environment variables add support for LEDs Signed-off-by: NEric Cooper <ecc@cmu.edu>
-
- 25 11月, 2010 1 次提交
-
-
由 Stefan Roese 提交于
Without this fix, the NAND_SPL target (in nand_spl/) is not built at all for those boards defining NAND_U_BOOT=y in boards.cfg. Signed-off-by: NStefan Roese <sr@denx.de> Cc: Scott Wood <scottwood@freescale.com>
-
- 10 11月, 2010 1 次提交
-
-
由 Kumar Gala 提交于
When P2020DS DDR2 was merged it was merged incorrectly and propogated to boards.cfg. Fix this by moving DDR2 config to be associated with P2020DS and not P1_P2_RDB. Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 26 10月, 2010 1 次提交
-
-
由 Mike Frysinger 提交于
Now that the boards.cfg file supports options to mkconfig, we can move the bf527-ezkit-v2 target out of the Makefile and into boards.cfg. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
- 25 10月, 2010 1 次提交
-
-
由 Dirk Eibach 提交于
Board support for the Guntermann & Drunck CATCenter Io. Board support for the Guntermann & Drunck IoCon. Signed-off-by: NDirk Eibach <eibach@gdsys.de> Signed-off-by: NStefan Roese <sr@denx.de>
-
- 24 10月, 2010 1 次提交
-
-
由 Wolfgang Denk 提交于
The 100MHz configuation of the VoVPN-GW has never been supported, so drop it now. Signed-off-by: NWolfgang Denk <wd@denx.de>
-
- 22 10月, 2010 5 次提交
-
-
由 John Schmoller 提交于
Initial support for Extreme Engineering Solutions XPedite5500 - a P2020-based PMC/XMC single board computer. Signed-off-by: NJohn Schmoller <jschmoller@xes-inc.com> Signed-off-by: NPeter Tyser <ptyser@xes-inc.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Peter Tyser 提交于
Some U-Boot images for X-ES boards support multiple products in the same family. For example, the XPedite5370, XPedite5371, and XPedite5372 are similar enough that one U-Boot image can work on all 3 cards. To make it clear that a U-Boot image can work on boards of the same family, rename the boards with the least significant digit of 'x'. While we're at it, change the board config file and make targets to be lowercase. Also change the default uImage and fdt filenames to "board.uImage" and "board.dtb" to be more generic. Signed-off-by: NPeter Tyser <ptyser@xes-inc.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Marek Vasut 提交于
This board is broken and it's not possible to repair it. Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
-
由 Marek Vasut 提交于
This board is broken and impossible to repair without deep knowledge or availability of the hardware. Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
-
由 Marek Vasut 提交于
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
-
- 21 10月, 2010 3 次提交
-
-
由 Nobuhiro Iwamatsu 提交于
Move the sh4 target boards out of the Makefile and into boards.cfg. And fix sh4 of MAKEALL. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Move the sh3 target boards out of the Makefile and into boards.cfg. And fix sh3 of MAKEALL. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Nobuhiro Iwamatsu 提交于
Move the rsk7203 target out of the Makefile and into boards.cfg. And fix sh2 of MAKEALL. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
- 20 10月, 2010 5 次提交
-
-
由 Mike Frysinger 提交于
The "options" field at the moment is only documented in the changelog which isn't terribly useful to people without git. Signed-off-by: NMike Frysinger <vapier@gentoo.org>
-
由 Kristoffer Ericson 提交于
This patch adds support for the HP Jornada flashboards that were made in 2008. Older flashroms should work if memory registers are adjusted. Signed-off-by: NKristoffer Ericson <kristoffer.ericson@gmail.com> Adpted for TEXT_BASE -> CONFIG_SYS_TEXT_BASE rename. Removed now redundant board/jornada/config.mk file. Removed unused empty jornada_init() function to silence "jornada.c:35: warning: 'jornada_init' defined but not used" Signed-off-by: NWolfgang Denk <wd@denx.de>
-
由 Marek Vasut 提交于
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
-
由 Marek Vasut 提交于
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
-
由 Marek Vasut 提交于
The following hardware is currently supported: - UART - USB Host - FPGA Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
-