The pattern of polling on a status register until a bit is set or a
timeout occurs is repeated multiple times in the driver. Mutualize the
code by introducing the nand_wait_int() helper that does wait for the
bit to flip or returns an error in case of timeout.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Acked-by: NBoris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>

Change NFC_SEND_ADR to NFC_SEND_ADDR.
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Acked-by: NBoris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>

In the nand_read_buffer() step, the seed is calculated by doing a modulo
by conf->nseeds which is always zero when not using the randomizer (most
of SLC NANDs).

This situation turns out to lead to a run time freeze with certain
toolchains.

Derive this seed only when the randomizer is enabled (and conf->nseeds
logically not zero), exactly like what has been done before with an
identical situation, see commit ea3f750c ("nand: sunxi: Fix modulo
by zero error").
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Acked-by: NBoris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>

When the requested ECC strength does not exactly match the strengths
supported by the ECC engine, the driver is selecting the closest
strength meeting the 'selected_strength > requested_strength'
constraint. Fix the fact that, in this particular case, ecc->strength
value was not updated to match the 'selected_strength'.

For instance, one can encounter this issue when no ECC requirement is
filled in the device tree while the NAND chip minimum requirement is not
a strength/step_size combo natively supported by the ECC engine.
Suggested-by: NBoris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Acked-by: NBoris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>

A previous commit introduced the use of binman in the SPL.

After the binman_sym call over the 'pos' symbol, the output value is
checked against BINMAN_SYM_MISSING (-1UL). According to the
documentation (tools/binman/README), when it comes to the 'pos'
attribute:

pos:
	This sets the position of an entry within the image. The first
	byte of the image is normally at position 0. If 'pos' is not
	provided, binman sets it to the end of the previous region, or
	the start of the image's entry area (normally 0) if there is no
	previous region.

So instead of checking if the return value is BINMAN_SYM_MISSING, we
should also check if the value is not null.

The failure happens when using both the SPL file and the U-Boot file
independently instead of the concatenated file (SPL + padding + U-Boot).
This is because the U-Boot binary file alone does not have the U-Boot
header while it is present in the concatenation file. Not having the
header forces the SPL to discover where it should load U-Boot. The
binman_sym call is supposed to do that but fails. Because of the wrong
check, the destination address was set to 0 while it should have been
somewhere in RAM. This, obviously, stalls the board.

Fixes: 8bee2d25 ("binman: Add binman symbol support to SPL")
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>

Add proper and simple kconfig option for dram_sun8i_a83t.c
instead of using MACH type on Makefile.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>

Add proper and simple kconfig option for dram_sun8i_a33.c
instead of using MACH type on Makefile.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>

Add proper and simple kconfig option for dram_sun8i_a23.c
instead of using MACH type on Makefile.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>

Add proper and simple kconfig option for dram_sun9i.c
instead of using MACH type on Makefile.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>

Add proper and simple kconfig option for dram_sun4i.c
instead of using MACH type on Makefile.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>

Add proper and simple kconfig option for dram_sun6i.c
instead of using MACH type on Makefile.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>

Add simple and meaningful kconfig option for pmic_bus.c
instead of using MACH type on Makefile.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>

Add simple and meaningful kconfig option for rsb.c
instead of using MACH type on Makefile.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>

SUN6I_PRCM is also used for SUN8I and SUN9I, so
select the same on respective MACH types.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>

Add simple and meaningful kconfig option for p2wi.c
instead of using MACH type on Makefile.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>

Add simple and meaningful kconfig option for prcm.c
instead of using MACH type on Makefile.

PRCM (Power/Reset/Clock Management) is considered as a
Multi-Functional Device, so used the same on Kconfig definition.
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>

Merge init_helpers.h in the new file init.h
with only prototypes for init_cache_f_r
used in common/board_f.c
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>

Move function prototype for common/init/board_init.c
from common.h to init.h
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>

Move function prototypes used in common/board_r.c
from common.h to init.h
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>

Move function prototypes for common/init/board_init.c
from common.h to init.h
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>

Move prototypes for function used in common/board_f.c
from common.h to init.h
Remove weak for arch_reserve_stacks in prototype
(checkpatch issue)
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>

This file is completely unused and it should be removed as the part of
ppc405/ppc440 xilinx platform removal.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Remove a link to a non-existent file.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: NAndrew F. Davis <afd@ti.com>

Remove non-existing paths.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Remove non-existing directories.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: NMinkyu Kang <mk7.kang@samsung.com>

Change due to commit b08c8c48 ("libfdt: move headers to
<linux/libfdt.h> and <linux/libfdt_env.h>")
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Fix an incorrect path.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

arch/arm/cpu/armv7/mx*/ does not relate to any existing directory.
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>

The 2 functions board_power_mode and board_poweroff
are no more existing in U-Boot code (check with grep)
This patch updates the documentation and removes
the unnecessary prototypes.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>

Remove the prototypes for 4 functions no more existing
in U-Boot code (checked by grep):
- checkflash
- checkdram
- mdm_init
- setup_board_extra
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>

Add a new file init.h with the prototype for arch_cpu_init
Add a prototype for mach_cpu_init() to avoid a warning:
no previous prototype for ‘mach_cpu_init’

It is a first step to move all the functions prototype
used during U-Boot initialization (board_f.c / board_r.c)
from common.h to init.h
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

This converts the following to Kconfig:
   CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them.  They're also sometimes used for things not
directly inside of the serial driver.  First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it.  Next, consolidate all of these into the single entry in
drivers/serial/Kconfig.  Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: NTom Rini <trini@konsulko.com>

It is safe to always setup the pinmux for UART1 and UART3 to be used in
early_padconf and then if these pins are needed later on, they will be
re-muxed.  This allows us to drop the usage of CONFIG_CONS_INDEX here.

Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>

Due to adding various new functionalities with SPI and SPI-FLASH
subsystems which are rounding in Mailing list for year these long
term supporting spi driver which never seen any update with
driver-model conversion.

So added migration plan for DM_SPI and DM_SPI_FLASH with
deadline v2018.09
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>

Adds a dedicated defconfig to build TI K2L secure
devices and updates MAINTAINERS.

k2l_hs_evm_defconfig is created from the k2l_evm_defconfig
and removes support for SPL, as SPL is not supported on K2
HS devices. Corrects SYS_TEXT_BASE for HS devices.

Also adds TI_SECURE_DEVICE and FIT_IMAGE_POST_PROCESS to
include support for secure image creation and authentication
Signed-off-by: NMadan Srinivas <madans@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>
Acked-by: NAndrew F. Davis <afd@ti.com>

This patch updates the default u-boot env for K2L HS devices
to install the secure boot monitor and load the fitImage during
boot.
Signed-off-by: NMadan Srinivas <madans@ti.com>
Acked-by: NAndrew F. Davis <afd@ti.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

Remove busy looping during watchdog reset.
Each polling of W_PEND_WTGR bit ("finish posted
write") after watchdog reset takes 120-140us
on BeagleBone Black board. Current U-Boot code
has watchdog resets in random places and often
there is situation when watchdog is reset
few times in a row in nested functions.
This adds extra delays and slows the whole system.

Instead of polling W_PEND_WTGR bit, we skip
watchdog reset if the bit is set. Anyway, watchdog
is in the middle of reset *right now*, so we can
just return.

This noticeably increases performance of the
system. Below are some measurements on BBB:
 - DFU upload over USB                 15% faster
 - fastboot image upload               3x times faster
 - USB ep0 transfers with 4k packets   20% faster
Signed-off-by: NRuslan Bilovol <ruslan.bilovol@gmail.com>
Tested-by: NSam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>
Tested-by: NAlex Kiernan <alex.kiernan@gmail.com>

serial# variable is needed to show the device correctly in "fastboot
devices" output. It's useful when we have several devices (in fastboot
mode) connected to single host and want to choose which one to flash.

We can't use omap_die_id_serial() for this, because AM335x lacks
DIE_ID, as can be seen from AM335x TRM. Let's do next:
 - reuse board_serial variable (obtained from EEPROM in
   set_board_info_env() function) to set serial#
 - if board_serial is "unknown", reuse ethaddr variable to set serial#
Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: NTom Rini <trini@konsulko.com>

To support set/get the clock rate, add set/get_rate operations.
Signed-off-by: NWenyou Yang <wenyou.yang@microchip.com>

As said in the SAMA5D2 datasheet, the PLLA clock must be divided
by 2 by writing the PLLADIV2 bit in PMC_MCKR, if the ratio between
PCK and MCK is 3 (MDIV = 3). This is the purpose of the driver.
Signed-off-by: NWenyou Yang <wenyou.yang@microchip.com>