Select CONFIG_CMD_NET and CONFIG_CMD_SETEXPR by default rather then
needing to have this in every sunxi defconfig file.

This also fixes the Merrii_A80_Optimus defconfig no longer building.

Cc: Maxin B. John <maxin.john@enea.com>
Reported-by: NMaxin B. John <maxin.john@enea.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

The Mele A1000G-quad and the Mele M9 have the same PCB, sofar we've been
using the same defconfig (and dts on the kernel side) for both models.
Unfortunately this does not work for the otg controller, on the M9 this
is routed to a micro-usb connector on the outside, while as on the
A1000G-quad it is connected to an usb to sata bridge.

This commit adds a new defconfig for the Mele-A1000G-quad to allow using
different otg controller settings on the 2 boards.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

This also selects CONFIG_NET for any CONFIG_CMD_NET board.

Remove the imx default for CONFIG_NET.

This moves the config that was defined by 60296a83 (commands: add more
command entries in Kconfig).
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>

Another shell scripting command that has not been moved.

Moved using tools/moveconfig.py using these settings:

CMD_SETEXPR bool n y
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>

In order to reduce merge conflicts and to maintain the simplest possible
defconfig files, we should be using the savedefconfig feature of Kconfig
every time a new feature is added. This keeps the defconfig settings to
a minimum (only those things not default) and keeps them in the same
order as the Kconfig options.
Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Cc: Tom Rini <trini@konsulko.com>

Now that we've everything prepared for it remove the DM settings from the
defconfig(s) and simply always set them for sunxi.

This makes all sunxi boards allways use the driver model for gpios and
ethernet, and allows us to move over more bits to the driver-model without
the need to introduce #ifdef-ery for boards which are not yet using DM.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

This is a preparation patch for switching all sunxi boards over to using
the driver model.

Note that rather then defining both CONFIG_DEFAULT_DEVICE_TREE (for u-boot)
and CONFIG_FDTFILE (for the kernel), this commit simply replaces all
CONFIG_FDTFILE defconfig settings with CONFIG_DEFAULT_DEVICE_TREE and
uses CONFIG_DEFAULT_DEVICE_TREE for setting the default fdtfile env value
in sunxi-common.h .
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

Move this to Kconfig and clean up board config files that use it. Also
rename it to CONFIG_ETH_DESIGNWARE to fit with the naming that exists
in drivers/net/Kconfig.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Version 1:
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

Since commit e02ee254 (kconfig: switch to single .config
configuration), the prefixes in defconfig files such as "+S:",
"+ST:", etc., are meaningless.

This commit was generated by the following command:

  find configs -name '*_defconfig' | xargs sed -i 's/^+*S*T*://'
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>

CONFIG_TARGET_FOO is only used in board/sunxi/Makefile to select the
dram config for sun5i and sun7i boards and in board/sunxi/gmac.c for some
special handling of the bananapi/bananapro (both sun7i), iow it is not used
at all on any sun4i, sun6i and sun8i boards so lets get rid of it there.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

The dcdc1 voltage is typically used as generic 3.3V IO voltage for things like
GPIO-s, sdcard interfaces, etc. On most boards this is undervolted to 3.0V to
safe battery, but not on all, make it configurable so that we can use the
same settings as the original firmware on all boards.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

Some of the ldo-s of the axp221 are used in the same way on most boards, add
comments to the Kconfig help text to reflect this, and give them defaults
matching their typical usage.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

It turns out that there is a too large spread between boards to handle this
with a default value, turn this into Kconfig options, and set the values
the factory images are using for the Colombus and Mele_M9 boards.

Note this changes the ZQ default when not overriden through defconfig from
120 to 123, as that is what most boards seem to actually use.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

Hookup the gmac found on the sun6i / A31 SoCs.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

I noticed that the kernel and u-boot settings were different, double checking
has confirmed that the kernel settings are correct.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>

Add support for the 2 ehci controllers found on the sun6i (A31) soc.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>
Acked-by: NMarek Vasut <marex@denx.de>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NIan Campbell <ijc@hellion.org.uk>