- Generic UDP framework
- TFTP fixes
- dwc_eth_qos, smc911x, smc911x and mscc phy fixes

This commits update the support of sntp to use
the framework udp. This change allows to remove
all the reference to sntp in the main network
file net/net.c.
Signed-off-by: NPhilippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This commit enable the support of the generic udp protocol.
Signed-off-by: NPhilippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This commit adds a generic udp protocol framework in the
network loop. So protocol based on udp may be implemented
without modifying the network loop (for example custom
wait magic packet).
Signed-off-by: NPhilippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>

Add support for stingray PAXB PHY controller driver.
This driver supports maximum 8 PAXB phys using pipemux data.
Signed-off-by: NSrinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: NRayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: NStefan Roese <sr@denx.de>

Write the 'No ethernet found' message via the log drivers. This allows
suppressing it during output via the syslog driver.

This fixes the problem reported in:

[PATCH 0/4] log: Fix the syslog spam when running tests
https://lists.denx.de/pipermail/u-boot/2020-September/426343.htmlReported-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

When load the last block, the "len" might not be a block size. This cause
loading the incorrect last block data.

The fix change "len" to tftp_block_size and minus one tftp_block_size
for offset calculation.

Use same offset calculation formula as in store_block().
Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>
Reviewed-By: NRamon Fried <rfried.dev@gmail.com>

tftp_cur_block start with 1 for first block, but tftp_cur_block counter is
start with zero when block number is rollover. The existing code
"tftp_cur_block - 1" will cause the block number become -1 in store_block()
when tftp_cur_block is 0 when tftp_cur_block is rollover.

The fix pass in tftp_cur_block to store_block() and minus the
tftp_block_size when do the offset calculation.
Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>
Reviewed-By: NRamon Fried <rfried.dev@gmail.com>

Fixes missing update to tftp_prev_block counter before increase
tftp_cur_block counter when do the tftpput operation.

tftp_prev_block counter is used in update_block_number() function to
check whether block number (sequence number) is rollover. This bug
cause the tftpput command fail to upload a large file when block
number is greater than 16-bit (0xFFFF).
Signed-off-by: NLey Foon Tan <ley.foon.tan@intel.com>
Reviewed-By: NRamon Fried <rfried.dev@gmail.com>

The ethernet controller can read the MAC from EEPROM and display it,
but if ethaddr is not set, the ethernet is still unavailable.

This patch checks will automatically set the MAC address if it has
not already been set.
Signed-off-by: NAdam Ford <aford173@gmail.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

ftgmac100 driver is using hard-coded PHY interface address of zero.
Each board can have different PHY interface address (phy_addr).
This commit modifies the driver to make use of board specific address
by leveraging CONFIG_PHY_ADDR.
Signed-off-by: NThirupathaiah Annapureddy <thiruan@linux.microsoft.com>
Reviewed-by: NCédric Le Goater <clg@kaod.org>

The Linux kernel does set the clock delays to
- 0.2 ns (their default, and lowest, hardware value) if delays should
  not be enabled
- 2.0 ns (which causes the data to be sampled at exactly half way between
  clock transitions at 1000 Mbps) if delays should be enabled
depending on the interface mode

See https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/phy/mscc/mscc_main.c#n523

So instead of using arbitrary delay values like now, mimic this behaviour.

The behaviour is the same for all of vsc8530/8531/8540/8541 so move that
to a shared function while at it.
Signed-off-by: NHeiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

The vsc8530/8531/8540/8541 phys have a configurable clock output that
can emit 25, 50 and 125 MHz rates, which in turn may be needed for
stable network connections.

This follows a similar change introduced into the Linux kernel at
  https://lore.kernel.org/netdev/20200609133140.1421109-2-heiko@sntech.deSigned-off-by: NHeiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>

- SCMI firmware support
- regmap, GPIO, reset API enhancements

Add tests for SCMI reset controllers. A test device driver
sandbox-scmi_devices.c is used to get reset resources, allowing further
resets manipulation.

Change sandbox-smci_agent to emulate 1 reset controller exposed through
an agent. Add DM test scmi_resets to test this reset controller.
Signed-off-by: NEtienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This change introduces a reset controller driver for SCMI agent devices.
When SCMI agent and SCMI reset domain drivers are enabled, SCMI agent
binds a reset controller device for each SCMI reset domain protocol
devices enabled in the FDT.

SCMI reset driver is embedded upon CONFIG_RESET_SCMI=y. If enabled,
CONFIG_SCMI_AGENT is also enabled.

SCMI Reset Domain protocol is defined in the SCMI specification [1].

Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmiSigned-off-by: NEtienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Add tests for SCMI clocks. A test device driver sandbox-scmi_devices.c
is used to get clock resources, allowing further clock manipulation.

Change sandbox-smci_agent to emulate 3 clocks exposed through 2 agents.
Add DM test scmi_clocks to test these 3 clocks.
Update DM test sandbox_scmi_agent with load/remove test sequences
factorized by {load|remove}_sandbox_scmi_test_devices() helper functions.
Signed-off-by: NEtienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This change introduces a clock driver for SCMI agent devices. When
SCMI agent and SCMI clock drivers are enabled, SCMI agent binds a
clock device for each SCMI clock protocol devices enabled in the FDT.

SCMI clock driver is embedded upon CONFIG_CLK_SCMI=y. If enabled,
CONFIG_SCMI_AGENT is also enabled.

SCMI Clock protocol is defined in the SCMI specification [1].

Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmiSigned-off-by: NEtienne Carriere <etienne.carriere@linaro.org>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Dump SCMI DT bindings documentation from Linux kernel source
tree v5.8-rc1.
Signed-off-by: NEtienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This change implements a SMCCC transport for SCMI exchanges. This
implementation follows the Linux kernel as references implementation
for SCMI message processing, using the SMT format for communication
channel meta-data.

Use of SMCCC transport in SCMI FDT bindings are defined in the Linux
kernel DT bindings since v5.8. SMCCC with SMT is implemented in OP-TEE
from tag 3.9.0 [2].

Links: [2] https://github.com/OP-TEE/optee_os/commit/a58c4d706d23Signed-off-by: NEtienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This change implements a mailbox transport using SMT format for SCMI
exchanges. This implementation follows the Linux kernel and
SCP-firmware [1] as references implementation for SCMI message
processing using SMT format for communication channel meta-data.

Use of mailboxes in SCMI FDT bindings are defined in the Linux kernel
DT bindings since v4.17.

Links: [1] https://github.com/ARM-software/SCP-firmwareSigned-off-by: NEtienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This change introduces SCMI agent uclass to interact with a firmware
using the SCMI protocols [1].

SCMI agent uclass currently supports a single method to request
processing of the SCMI message by an identified server. A SCMI message
is made of a byte payload associated to a protocol ID and a message ID,
all defined by the SCMI specification [1]. On return from process_msg()
method, the caller gets the service response.

SCMI agent uclass defines a post bind generic sequence for all devices.
The sequence binds all the SCMI protocols listed in the FDT for that
SCMI agent device. Currently none, but later change will introduce
protocols.

This change implements a simple sandbox device for the SCMI agent uclass.
The sandbox nicely answers SCMI_NOT_SUPPORTED to SCMI messages.
To prepare for further test support, the sandbox exposes a architecture
function for test application to read the sandbox emulated devices state.
Currently supports 2 SCMI agents, identified by an ID in the FDT device
name. The simplistic DM test does nothing yet.

SCMI agent uclass is designed for platforms that embed a SCMI server in
a firmware hosted somewhere, for example in a companion co-processor or
in the secure world of the executing processor. SCMI protocols allow an
SCMI agent to discover and access external resources as clock, reset
controllers and more. SCMI agent and server communicate following the
SCMI specification [1]. This SCMI agent implementation complies with
the DT bindings defined in the Linux kernel source tree regarding
SCMI agent description since v5.8.

Links: [1] https://developer.arm.com/architectures/system-architectures/software-standards/scmiSigned-off-by: NEtienne Carriere <etienne.carriere@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

The tests rely on a dummy driver to allocate and initialize the regmaps
and the regmap fields using the managed API. The first test checks if
the regmap config fields like width, reg_offset_shift, range specifiers,
etc work. The second test checks if regmap fields behave properly (mask
and shift are ok) by peeking into the regmap.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: NPratyush Yadav <p.yadav@ti.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

When more nodes are added for a uclass the index might go into two or
more digits. This means that there are less spaces printed because they
are used up by the extra digits. Update the regular expression to allow
variable-length spacing between the class name and and index.

This was discovered when adding a simple_bus node in test.dts made
test_bind_unbind_with_uclass() fail because the index went up to 10.
Signed-off-by: NPratyush Yadav <p.yadav@ti.com>

A regmap field is an abstraction available in Linux. It provides to access
bitfields in a regmap without having to worry about shifts and masks.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NPratyush Yadav <p.yadav@ti.com>

Some devices need to calculate the regmap base address at runtime. This
makes it impossible to use device tree to get the regmap base. Instead,
allow devices to specify it in the regmap config. This will create a
regmap with a single range that corresponds to the start and size given
by the driver.
Signed-off-by: NPratyush Yadav <p.yadav@ti.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Right now, the base of a regmap can only be obtained from the device
tree. This makes it impossible for devices which calculate the base at
runtime to use a regmap. An example of such a device is the Cadence
Sierra PHY.

Allow creating a regmap with one range whose start and size can be
specified by the driver based on calculations at runtime.
Signed-off-by: NPratyush Yadav <p.yadav@ti.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Drivers can configure it to adjust the final read/write location.
Signed-off-by: NPratyush Yadav <p.yadav@ti.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Right now, regmap_read() and regmap_write() read/write a 32-bit value
only. To write other lengths, regmap_raw_read() and regmap_raw_write()
need to be used.

This means that any driver ported from Linux that relies on
regmap_{read,write}() to know the size already has to be updated at each
callsite. This makes the port harder to maintain.

So, allow specifying the read/write width to make it easier to port the
drivers, since now the only change needed is when initializing the
regmap.
Signed-off-by: NPratyush Yadav <p.yadav@ti.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Some fields will be introduced in the regmap structure that should be
set to 0 by default. So, once we allocate a regmap, make sure it is
zeroed out to avoid unexpected defaults for those values.
Signed-off-by: NPratyush Yadav <p.yadav@ti.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Most of new linux drivers are using managed-API to allocate resources. To
ease porting drivers from linux to U-Boot, introduce devm_regmap_init() as
a managed API to get a regmap from the device tree.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NPratyush Yadav <p.yadav@ti.com>

Add a test to verify that GPIOs can be acquired/released using the managed
API. Also check that the GPIOs are released when the consumer device is
removed.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NPratyush Yadav <p.yadav@ti.com>

Add managed functions to get a gpio from the devce-tree, based on a
property name (minus the '-gpios' suffix) and optionally an index.

When the device is unbound, the GPIO is automatically released and the
data structure is freed.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NPratyush Yadav <p.yadav@ti.com>

The tests are basically the same as for the regular API. Except that
the reset are initialized using the managed API, and no freed manually.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NPratyush Yadav <p.yadav@ti.com>

Add managed functions to get a reset_ctl from the device-tree, based on a
name or an index.
Also add a managed functions to get a reset_ctl_bulk (array of reset_ctl)
from the device-tree.

When the device is unbound, the reset controllers are automatically
released and the data structure is freed.
Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Signed-off-by: NPratyush Yadav <p.yadav@ti.com>

- Disable CMD_IRQ for RISC-V.
- Update sipeed/maix doc
- Obtain reg of SiFive RAM via dev_read_addr_index() instead of regmap API.
- Cleans up RISC-V timer drivers and converts them to DM.
- Correctly handle IPIs already pending upon prior stage bootloader (on the K210)

- Improve our dev_xxx(..) wrappers to be generally used and available
  rather than discarded at link/compile time.

This adorns messages generated by dev_xxx with the device and driver
names. It also redirects dev_xxx to log when it is available. The names
of these functions very roughly take inspiration from Linux, but there is
no deeper correlation.

Both struct udevice and struct device are supported when logging, though
logging with struct device is no better than using log_xxx. The latter is
supported because of the large amount of existing code which logs with
struct device.
Signed-off-by: NSean Anderson <seanga2@gmail.com>
Tested-by: NPatrick Delaunay <patrick.delaunay@st.com>

This substitutes literal log levels with their symbolic constants.
Signed-off-by: NSean Anderson <seanga2@gmail.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Tested-by: NPatrick Delaunay <patrick.delaunay@st.com>