Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Drop SPI support saving precious 4 Kb on boards with tough size
restrictions.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: NMarcel Ziswiler <marcel@ziswiler.com>

Unset CONFIG_CMDLINE_EDITING saving precious 4 Kb on boards with tough
size restrictions.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>

Unset CONFIG_EFI_UNICODE_CAPITALIZATION on boards with tough size
restrictions.

This is analogous to commit a90bf07a
("efi_loader: unset CONFIG_EFI_UNICODE_CAPITALIZATION").
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: NAlexander Graf <agraf@suse.de>

Due to revert of commit c0434407, this board does not build
any more. Disable CONFIG_DISPLAY_CPUINFO for v2018.11 release.

This commit should be reverted after v2018.11 release.
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
Acked-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Real marketing name of the board was recently updated so
to accommodate that change renaming the board and all
related to it.
Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>

On our demo setup for SD card boot, the u-boot environment
is in a FAT partition.

This patch changes the default configuration, specifing that
the u-boot environment is in a FAT partition instead of raw MMC.
Signed-off-by: NAndrei Stefanescu <andrei.stefanescu@microchip.com>
Acked-by: NEugen Hristev <eugen.hristev@microchip.com>

The Pine A64 Plus/non-Plus model detection code is now built on all
64-bit ARM SoCs, even if the code cannot be triggered when H5/H6 is in
use.

Disable them when the board is Pine A64 by adding a Kconfig option that
is only selected on Pine A64.

On GCC 7.3.1 this makes the size of the function reduces 184 bytes, and
saves a 104 byte strstr() function, then makes SPL on H6 succeed to
build.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Acked-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: NJagan Teki <jagan@openedev.com>

The build breaks because its not fitting the U-Boot binary into the ROM
image. So lets move VGA BIOS a bit to make room for the grown U-Boot
binary.
Signed-off-by: NStefan Roese <sr@denx.de>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

To enable the root device selection (kernel cmd-line) via PARTUUID, this
patch enables CMD_PART on all missing theadorable-x86 boards and
changes the default environment to generate the root=PARTUUID string
automatically.

This fixes problems that have been noticed on systems with multiple
SATA/AHCI controller connected via PCIe, where the device name for the
root device / partition (/dev/sdaX) was incorrect.
Signed-off-by: NStefan Roese <sr@denx.de>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

To help with size constraints, enable thumb2 when building.
Signed-off-by: NTom Rini <trini@konsulko.com>

The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.
Signed-off-by: NJeremy Gebben <jgebben@sweptlaser.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>

Odroid HC2 board is based on Odroid XU4 board, like the Odroid HC1.

The linux kernel does not provide a hc2 DTB so the hc1 DTB is also used
for the Odroid HC2.

Resend because MUA changed whitespace.
Signed-off-by: NDirk Meul <dirk.meul@rwth-aachen.de>
Acked-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>
Signed-off-by: NMinkyu Kang <mk7.kang@samsung.com>

The DM37 and OMAP35 SOM-LV SOM-LV products both support a NOR
flash part connected to CS2 in addition to the NAND part on CS0.
This patch setups the GPMC timings for the MT28 NOR Flash and
enables the CFI-Flash driver now that the CFI stuff is in Kconfig
Signed-off-by: NAdam Ford <aford173@gmail.com>

Instead of keeping a custom environment, use a more generic approach
by switching to distro config.
Signed-off-by: NDirk Meul <dirk.meul@rwth-aachen.de>
Reviewed-by: NFabio Estevam <festevam@gmail.com>

Add default bootargs for the MMC defconfig to use SD-Card as rootfs
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Add the default kernel bootargs according to our NAND flash demo layout:
http://www.at91.com/linux4sam/bin/view/Linux4SAM/Sama5d2PtcEKMainPage#NAND_Flash_demo_Memory_mapSigned-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Enable onewire support and commands, fdt overlay for the emmc defconfig.
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Enable onewire support and commands, fdt overlay for the mmc1 defconfig.
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Enable iminfo command with CONFIG_CMD_IMI
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

Enabled FIT image support and iminfo command for FIT information.
Signed-off-by: NEugen Hristev <eugen.hristev@microchip.com>

The da850evm does not need this enabled, so this removes a
notice that appears during compile time that says
"Please remove"
Signed-off-by: NAdam Ford <aford173@gmail.com>

Add default configuration to run u-boot as BL33 in the ARM Trusted Firmware
boot flow for AArch32 case.
Signed-off-by: NRui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: NBryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Cc: u-boot@lists.denx.de

We may have, the not yet considered, scenario where OPTEE is loaded before
u-boot and *not* by u-boot, e.g, the boot flow using the ARM Trusted
Firmware (ATF), where in the 32bit flow is:
BootRom->ATF(BL2)->Optee(BL32)->u-boot(BL33)

In this case we need still to reserve the memory used by optee, to avoid
for example to realocate ourself to the same address at the end of DRAM.
So, we change here the dependencies on the OPTEE lib and we set the default
size and base of TZRAM to zero.
Signed-off-by: NRui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: NBryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: u-boot@lists.denx.de

Move this option to Kconfig and tidy up the config file of eight
boards which use it.
Signed-off-by: NXiaoliang Yang <xiaoliang.yang_1@nxp.com>

Update README
Add imximage.cfg
Update defconfig to include imximage.cfg
Signed-off-by: NPeng Fan <peng.fan@nxp.com>

Add i.MX8QXP MEK board support
Enabled pinctrl/clk/power-domain/mmc/i2c/fec driver.
Added README file.
Signed-off-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NAnatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>

Since commit 380d4f78 ("rtc: Allow use of RTC in SPL and TPL")
qemu-x86_64_defconfig does not boot anymore.

Fixes: 380d4f78 ("rtc: Allow use of RTC in SPL and TPL")
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: NBin Meng <bmeng.cn@gmail.com>

With bootstage now allocating pre-relocation memory the current amount
available is insufficient. Increase it a little.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NBin Meng <bmeng.cn@gmail.com>

This converts the following to Kconfig:
   CONFIG_FLASH_CFI_DRIVER
   CONFIG_SYS_FLASH_USE_BUFFER_WRITE
   CONFIG_FLASH_CFI_MTD
   CONFIG_SYS_FLASH_PROTECTION
   CONFIG_SYS_FLASH_CFI
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: NTom Rini <trini@konsulko.com>

The explicit arch specific build symbol allows to group supported
boards, generalize common config options and it will serve as
a dependency for platform only drivers.

Two related board defconfigs are resynced after the change.
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>

This patch enables the cache command, mostly for convenience of testing.
Signed-off-by: NHiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>

This patch removes 'console=' argument, because kernel uses
stdout-path as parameter.
Signed-off-by: NHiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>

Simplify defconfig for ZynqMP but keep option not to enable it for mini
targets.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Virtual QEMU board is generating DTB self and putting it to
VERSAL_QEMU_DTB_ADDR address.
Board is using CONFIG_OF_BOARD which ensures that u-boot is aligned with
board created by QEMU.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Ethernet is not present on this board that's why there are two other
options how to wire the board to ethernet. The first is asix_eth usb
host converter which is already enabled by default. The second option is
to use USB CDC/RNDIS ethernet gadget.

This patch is enabling CDC which is working with Linux.
With new bind/unbind command there is no need to call usb_ether_init()
from platform code and use for example these commands:

bind /amba/usb0@ff9d0000/dwc3@fe200000 usb_ether
dhcp
unbind /amba/usb0@ff9d0000/dwc3@fe200000
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

There are some inconsistencies which should be fixed.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Xilinx DLC20 has I2C0 with EEPROM(1KB), UART1, GPIO, SD0 (EMMC 4GB),
USB0 device, ENET0, QSPI (16MB) and DDR(two of 256MB each).

Boards have mix of Winbond/ST QSPIs.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Enable loading FPGA from FIT image in SPL.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>

Add Menlosystems M53 board, based on the M53 SoM.
This board has Ethernet, USB host, USB gadget, UART and LCD on it.
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>