updates is defined as unsigned int. So use %u for printf().
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

test->time_ms[] is defined as unsigned. So use %u for printf().
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

len is defined as unsigned. So use %u for printf().
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

gpio is defined as unsigned int. So we should use %u when calling printf().
Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Building with CONFIG_OF_EMBED generates build warnings, as it should
only be used for debugging purposes.

Remove CONFIG_OF_EMBED from all stm32 config files which are using
this flag.
Signed-off-by: NPatrice Chotard <patrice.chotard@st.com>

Make sure the block cache is cleared for the MMC device after it was
reinitialized to avoid having any stale data in the cache, like e.g.
partition tables or such.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>

In case the card is removed, force-init the MMC to start the internal
machinery which deregisters and invalidate the MMC device.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>

The mmc_select_mode_and_width() function can be called while the card
is in HS200/HS400 mode and can be used to downgrade the card to lower
mode, e.g. HS. This is used for example by mmc_boot_part_access_chk()
which cannot access the card in HS200/HS400 mode and which is in turn
called by saveenv if env is in the MMC.

In such case, forcing the card clock to legacy frequency cannot work.
Instead, the card must be switched to HS mode first, from which it can
then be reprogrammed as needed.

However, this procedure needs additional code changes, since the current
implementation checks whether the card correctly switched to HS mode in
mmc_set_card_speed(). The check only expects that the card will be going
to HS mode from lower modes, not from higher modes, hence add a parameter
which indicates that the HS200/HS400 to HS downgrade is happening. This
makes the code send the switch command first, reconfigure the controller
next and finally perform the EXT_CSD readback check. The last two steps
cannot be done in reverse order as the card is already in HS mode when
the clock are being switched on the controller side.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>

This adds device tree and the DM_MMC driver for the AM335x IGEP based
boards.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>

This adds device tree and the DM_MMC driver for the SL50 board.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>

This adds device tree for OMAP3 IGEP based boards and the DM_MMC driver.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: NTom Rini <trini@konsulko.com>

To save more space, switch to simple malloc here.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>

Enable TI_COMMON_CMD_OPTIONS and remove similar options
from the defconfig.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>

The USB support for this board was never really tested, in fact, the
presence of these options are more a copy & paste error from the
Beagleboard than a feature that really was used. As doesn't work, remove
for now. If someone at some point want to add this support he'll need to
migrate the board to use CONFIG_DM_USB instead.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>

The IGEP0032 board was never officially pushed upstream and actually I
don't have access to this hardware, unless someone with the hardware
wants to start working on this doesn't makes sense have this defconfig
here. So remove it.
Signed-off-by: NEnric Balletbo i Serra <enric.balletbo@collabora.com>

Some tests have ended up using double quotes where single quotes could be
used. Adjust this for consistency with the rest of U-Boot's Python code.
Signed-off-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>

Add MMC nodes for HiKey board based on HI6220 SoC. There are three MMC
controllers in this SoC, first one used for eMMC, second one used
for SD card and third one is not used by u-boot.
Signed-off-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NTom Rini <trini@konsulko.com>

Convert HiSilicon HI6220 MMC driver based on DWMMC IP to driver
model.
Signed-off-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>
[trini: Enable this on poplar]
Signed-off-by: NTom Rini <trini@konsulko.com>

Default 8MB gunzip size is not enough to load the release kernel, hence
fix 64MB size for uncompressing the kernel.
Signed-off-by: NManivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This patch replace OF_EMBED with OF_SEPARATE of defconfig files of
MediaTek boards because now OF_EMBED is only used for debugging purpose.
Signed-off-by: NWeijie Gao <weijie.gao@mediatek.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

This patch adds new file entries for MediaTek SoCs
Signed-off-by: NWeijie Gao <weijie.gao@mediatek.com>

Enable ethernet related configs to mt7629_rfb_defconfig.
Add default IP addresses.
Enable noncached memory region required by ethernet driver.
Signed-off-by: NMark Lee <Mark-MC.Lee@mediatek.com>

Enable ethernet related configs to mt7623n_bpir2_defconfig.
Add default IP addresses.
Enable noncached memory region required by ethernet driver.
Signed-off-by: NMark Lee <Mark-MC.Lee@mediatek.com>

This patch adds ethernet gmac node for MT7629 with internal gigabit phy.
Signed-off-by: NMark Lee <Mark-MC.Lee@mediatek.com>

This patch adds ethernet gmac node for MT7623 with MT7530 gigabit switch.
Signed-off-by: NMark Lee <Mark-MC.Lee@mediatek.com>

This patch adds ethernet support for Mediatek ARM-based SoCs, including
a minimum setup of the integrated switch.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NMark Lee <Mark-MC.Lee@mediatek.com>
Signed-off-by: NWeijie Gao <weijie.gao@mediatek.com>
Tested-By: N"Frank Wunderlich" <frank-w@public-files.de>

The ethsys contains not only the clock gating controller, but also the
reset controller for the whole ethernet subsystem and its components.

This patch adds binding of the reset controller so that the ethernet node
can have references on it.
Signed-off-by: NWeijie Gao <weijie.gao@mediatek.com>

This patch adds reset controller driver for MediaTek SoCs.
Signed-off-by: NRyder Lee <ryder.lee@mediatek.com>
Signed-off-by: NWeijie Gao <weijie.gao@mediatek.com>

It enables fastboot support on Poplar board by using DWC2 OTG gadget
driver.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

It enables DWC2 OTG gadget driver support for Poplar board.  As
usb2_phy_init() is being always called from board_init(), we can save
the call from board_usb_init().
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Booting an image currently sets the environment variable "fdtaddr"
by calling into 'cmd/fdt.c'. As a result, linking U-Boot fails if
CMD_FDT is not enabled.

Fix this by adding 'if (CONFIG_IS_ENABLED(CMD_FDT))' to the two
places where 'set_working_fdt_addr()' is called.
Signed-off-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Enable CONFIG_SPL_YMODEM_SUPPORT to support UART boot
Signed-off-by: NYan Liu <yan-liu@ti.com>
Reviewed-by: NLokesh Vutla <lokeshvutla@ti.com>

Add a test for the bootcount uclass, which uses the RTC bootcount backend
(i.e. drivers/bootcount/rtc.c is implictly also tested).
Signed-off-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: NSimon Glass <sjg@chromium.org>

Signed-off-by: NTom Rini <trini@konsulko.com>

The following hang is observed on a Hummingboard 2 MicroSOM
i2eX iMX6D - rev 1.3 with no eMMC populated on board:

U-Boot SPL 2018.11+gf6206f85 (Nov 16 2018 - 00:56:34 +0000)
Trying to boot from MMC1

U-Boot 2018.11+gf6206f85 (Nov 16 2018 - 00:56:34 +0000)

CPU:   Freescale i.MX6D rev1.5 996 MHz (running at 792 MHz)
CPU:   Extended Commercial temperature grade (-20C to 105C) at 33C
Reset cause: POR
Board: MX6 HummingBoard2
DRAM:  1 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

No panel detected: default to HDMI
Display: HDMI (1024x768)
In:    serial
Out:   serial
Err:   serial
---> hangs

which is caused by the following infinite loop inside esdhc_send_cmd_common()

	while (!(esdhc_read32(&regs->irqstat) & flags))
		;

Instead of looping forever, provide an exit path so that a timeout
error can be propagated in the case irqstat does not report
any interrupts, which may happen when no eMMC is populated on
board.
Reported-by: NRicardo Salveti <rsalveti@rsalveti.net>
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Tested-by: NPeter Robinson <pbrobinson@gmail.com>
Tested-by: NRicardo Salveti <rsalveti@rsalveti.net>

Chris Spencer reports that when enabling ext4 read support without
also enabling write support the following error is seen:

fs/fs.c:198:12: error: 'ext4_write_file' undeclared here (not in a
function); did you mean 'ext4_read_file'?
   .write = ext4_write_file,
            ^~~~~~~~~~~~~~~
Fix this problem by moving these options to Kconfig.
Reported-by: NChris Spencer <spencercw@gmail.com>
Acked-by: NPeng Fan <peng.fan@nxp.com>
Signed-off-by: NFabio Estevam <festevam@gmail.com>

Change CONFIG_ENV_OFFSET for Poplar to be 1MB further into the eMMC
than before.  This puts it immediately prior to the space we are
reserving offset 0x200000-0x400000 for UEFI to save its persistent
data.  Define CONFIG_ENV_SIZE as a product of env_mmc_nblks and the
sector size, like CONFIG_ENV_OFFSET is.
Signed-off-by: NAlex Elder <elder@linaro.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

This particular commit is causing a regression on stih410-b2260 and
other platforms when reading from FAT16.  Noting that I had rebased the
original fix from Thomas onto then-current master, there is also
question from Akashi-san if the change is still needed after other FAT
fixes that have gone in.

This reverts commit a68b0e11.
Reported-by: NPatrice Chotard <patrice.chotard@st.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Thomas RIENOESSL <thomas.rienoessl@bachmann.info>
Signed-off-by: NTom Rini <trini@konsulko.com>