- 20 12月, 2012 1 次提交
-
-
由 Yoshihiro Shimoda 提交于
The R0P7752C00000RZ board has SH7752, 512MB DDR3-SDRAM, SPI ROM, Gigabit Ethernet, and eMMC. This patch supports the following functions: - 512MB DDR3-SDRAM, SCIF4, SPI ROM, Gigabit Ethernet, eMMC Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
- 18 12月, 2012 2 次提交
-
-
- 16 12月, 2012 6 次提交
-
-
由 Yoshihiro Shimoda 提交于
SH7752 has two fast ethernet controllers and two gigabit ethernet controllers. It is similar to SH7757. Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Acked-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Joe Hershberger 提交于
The ip is stored in network order, so we can't test it in host order. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com> Reviewed-by: NKim Phillips <kim.phillips@freescale.com>
-
由 Simon Glass 提交于
This prints a tftp speed indication after the download completes. This is the 3.6 MiB/s indicator below. Tegra2 (SeaBoard) # tftp ... Using asx0 device TFTP from server 172.22.72.144; our IP address is 172.22.73.81 Filename '/tftpboot/uImage-user-seaboard-1'. Load address: 0x408000 Loading: ################################################# 3.6 MiB/s done Signed-off-by: NSimon Glass <sjg@chromium.org> Acked-by: NIgor Grinberg <grinberg@compulab.co.il>
-
由 trem 提交于
CONFIG_SYS_TFTP_LOADADDR is defined on severals boards, but it's never used. So we can safely removed it. Signed-off-by: NPhilippe Reynes <tremyfr@yahoo.fr>
-
由 Michal Simek 提交于
Marvell 88E1118R has different uid then 88E1118. Signed-off-by: NMichal Simek <monstr@monstr.eu> CC: Andy Fleming <afleming@freescale.com> CC: Zang Roy-R61911 <tie-fei.zang@freescale.com> CC: Kumar Gala <galak@kernel.crashing.org>
-
由 Ruchika Gupta 提交于
In e1000e driver, Rx descriptor queue is used such that hardware can add only one descriptor at a time. So the WTHRESH granularity in RXDCTL should be set to single descriptor. This would ensure that every time controller fills a Rx descriptor, it is flushed to host memory. Earlier this granularity was in cache line units i.e 2 descriptors. This leads to controller always waiting for 2 descriptors before flushing them out. But since not more than one Rx BD is actually available , the accumulation condition never gets hit. Signed-off-by: NRuchika Gupta <ruchika.gupta@freescale.com> Signed-off-by: NVakul Garg <vakul@freescale.com> Acked-by: NRoy Zang <tie-fei.zang@freescale.com>
-
- 15 12月, 2012 3 次提交
-
-
由 Eric Benard 提交于
- since commit 418396e2 nand write.raw can take the number of page to be written as an argument. nand_update_full is passing the size (in bytes) to nand write.raw. This value was previously ignored but now breaks the write. - this patch updates the default environment of these boards to provide a pagecount instead of a size to nand write.raw. - tested on a mx28evk with a 4k page NAND and on a custom board with a 2k page NAND. Signed-off-by: NEric Bénard <eric@eukrea.com> Cc: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: NMarek Vasut <marex@denx.de>
-
由 Scott Wood 提交于
-
由 Tom Rini 提交于
Signed-off-by: NTom Rini <trini@ti.com>
-
- 14 12月, 2012 28 次提交
-
-
由 Tom Rini 提交于
The #ifdef here is not enough to stop part_efi.c from being built, only being unused. And with recent changes this now leads to warnings. The easiest solution here is to just let the garbage collection at link time do its job. Signed-off-by: NTom Rini <trini@ti.com>
-
由 Joe Hershberger 提交于
Use the variable access flags to implement the protection for ethaddr and serial# instead of hard-coding them. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Implement a way to delete more than one variable at a time. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Now that we have support for permissions, add a way to override them. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Add support for read-only, write-once, and change-default. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Similar to the env callback command, this will show details about the options available, the static list, and the currently active variables. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Currently just validates variable types as decimal, hexidecimal, boolean, ip address, and mac address. Call env_acl_validate_setenv_params() from setenv() in fw_env.c. If the entry is not found in the env .flags, then look in the static one. This allows the env to override the static definitions, but prevents the need to have every definition in the environment distracting you. Need to build in _ctype for isdigit for Linux. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Currently just validates variable types as decimal, hexidecimal, boolean, ip address, and mac address. If the entry is not found in the env ".flags", then look in the static one. This allows the env to override the static definitions, but prevents the need to have every definition in the environment distracting you. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
The silent variable now updates the global data flag anytime it is changed as well as after the env relocation (in case its value is different from the default env in such cases as NAND env) Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Remove the hard-coded console handler and use a callback instead Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Remove the hard-coded loadaddr handler and use a callback instead Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Remove the hard-coded baudrate handler and use a callback instead Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Remove the hard-coded bootfile handler and use a callback instead Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
The callbacks can be bound, but are otherwise invisible. Add a command to show what callbacks are available. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com> !!! fix callback command
-
由 Joe Hershberger 提交于
Add support for per-variable callbacks to the "hashtable" functions. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com> !!!fix comment in callback
-
由 Joe Hershberger 提交于
When printing all variables with env print, don't print variables that begin with '.'. If env print is called with a '-a' switch, then include variables that begin with '.' (just like the ls command). Variables printed explicitly will be printed even without the -a. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Move the getenv_yesno() to env_common.c and change most checks for 'y' or 'n' to use this helper. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Move the read of the old value to inside the check function. In some cases it can be avoided all together and at the least the code is only called from one place. Also name the function and the callback to more clearly describe what it does. Pass the ENTRY instead of just the name for direct access to the whole data structure. Pass an enum to the callback that specifies the operation being approved. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
The same chunk of code was replicated in two places and the following changes will make that chunk grow a bit, so combine into a static func. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
Use a flag in hsearch_r for insert mode passed from import to allow the behavior be different based on use. Now that "do_check" is called for all imports, ensure console init is complete before updating the console on relocation import Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Joe Hershberger 提交于
isspace() and strim() are not in the typical user-mode string.h, so put them in a separate compilation unit so that they can be built into tools that need them independent of the other common string functions. This allows code shared by u-boot and the linux user-mode tools to link. Signed-off-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Lukasz Majewski 提交于
Enable support for GPT partition table restoration at Samsung's Trats development board. Signed-off-by: NLukasz Majewski <l.majewski@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> CC: Minkyu Kang <mk7.kang@samsung.com>
-
由 Piotr Wilczek 提交于
New command - "gpt" is supported. It restores the GPT partition table. It looks into the given environment variable for partitions definition. It can be enabled at target configuration file with CONFIG_CMD_GPT. Signed-off-by: NLukasz Majewski <l.majewski@samsung.com> Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
-
由 Lukasz Majewski 提交于
The restoration of GPT table (both primary and secondary) is now possible. Function 'gpt_restore' presents example of partition restoration process. Signed-off-by: NLukasz Majewski <l.majewski@samsung.com> Signed-off-by: NPiotr Wilczek <p.wilczek@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
-
由 Chang Hyun Park 提交于
Custom definitions of le_XX_to_int functions have been replaced with standard ones, defined at <compiler.h> Replacement of several GPT related structures members with ones indicating its endianness and proper size. Signed-off-by: NChang Hyun Park <heartinpiece@outlook.com> Signed-off-by: NLukasz Majewski <l.majewski@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
-
由 Lukasz Majewski 提交于
Documentation of the GPT format. Signed-off-by: NLukasz Majewski <l.majewski@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
-
由 Lukasz Majewski 提交于
This move is necessary to export gpt header and GPT partition entries to be used with other commands or subsystems. Additionally the part_efi.h file has been cleaned-up to supress checkpatch's warnings. Signed-off-by: NLukasz Majewski <l.majewski@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
-
由 Lukasz Majewski 提交于
The ustrtoul shall convert string defined size (e.g. 1GiB) to unsigned long type (as its name implies). Up till now it had returned int, which might cause problems with large numbers (GiB range), when interpreted as U2 signed numbers. Signed-off-by: NLukasz Majewski <l.majewski@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
-