- 24 10月, 2019 4 次提交
-
-
由 Jean-Jacques Hiblot 提交于
The xhci.h header file is currently located under drivers/usb/xhci Move it to the include/usb folder to make it available to drivers that are not under drivers/usb/xhci Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
-
由 Jean-Jacques Hiblot 提交于
This allow the phy to enter idle and then suspend. the K2 platforms require the PHY to be suspended before the USB domain clock can be turned off. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
-
由 Jean-Jacques Hiblot 提交于
This driver is not used anymore. Signed-off-by: NJean-Jacques Hiblot <jjhiblot@ti.com>
-
https://gitlab.denx.de/u-boot/custodians/u-boot-stm由 Tom Rini 提交于
- Disable CONFIG_NET flag for MCU STM32 - Fix ramdisk_addr_r for stm32f746-disco - Fix USB product id for stm32mp1
-
- 23 10月, 2019 1 次提交
-
-
https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq由 Tom Rini 提交于
- Add LS1027A, LS1018A, LS1017A support - Few updates related to usb, ls1012a, lx2160a
-
- 22 10月, 2019 7 次提交
-
-
由 Patrick Delaunay 提交于
Select the correct USB product id used by the download gadget for ST stm32mp1 boards. The board stm32mp1 select the correct product id, as defined in http://www.linux-usb.org/usb.ids for the STMicroelectronics vendor id = 0x0483 (CONFIG_USB_GADGET_VENDOR_NUM): - dfu = 0xdf11 : STM Device in DFU mode it is the value used by ROM code and reused for stm32prog command - fasboot = 0x0afb : Android Fastboot device - others = 0x5720 (CONFIG_USB_GADGET_PRODUCT_NUM) Mass Storage Device it is used for UMS command / usb_dnl_ums This patch avoid conflict when the same USB VID/PID is used for ums, fastboot or dfu command (two different protocols associated to the same PID). Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com> Acked-by: NPatrice Chotard <patrice.chotard@st.com>
-
由 Patrice Chotard 提交于
Set ramdisk_addr_r to 0xC0600000. Reported-by: NChristophe Priouzeau <christophe.priouzeau@st.com> Signed-off-by: NPatrice Chotard <patrice.chotard@st.com> Acked-by: NPatrick Delaunay <patrick.delaunay@st.com>
-
由 Patrice Chotard 提交于
Network support was never added on this board, disable CONFIG_NET flag to avoid following warning: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: NPatrice Chotard <patrice.chotard@st.com> Acked-by: NPatrick Delaunay <patrick.delaunay@st.com>
-
由 Patrice Chotard 提交于
Network support was never added on this board, disable CONFIG_NET flag to avoid following warning: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: NPatrice Chotard <patrice.chotard@st.com> Acked-by: NPatrick Delaunay <patrick.delaunay@st.com>
-
由 Patrice Chotard 提交于
Network support was never added on this board, disable CONFIG_NET flag to avoid following warning: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: NPatrice Chotard <patrice.chotard@st.com> Acked-by: NPatrick Delaunay <patrick.delaunay@st.com>
-
由 Patrice Chotard 提交于
Network support was never added on this board, disable CONFIG_NET flag to avoid following warning: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: NPatrice Chotard <patrice.chotard@st.com> Acked-by: NPatrick Delaunay <patrick.delaunay@st.com>
-
由 Patrice Chotard 提交于
Network support was never added on this board, disable CONFIG_NET flag to avoid following warning: ===================== WARNING ====================== This board does not use CONFIG_DM_ETH (Driver Model for Ethernet drivers). Please update the board to use CONFIG_DM_ETH before the v2020.07 release. Failure to update by the deadline may result in board removal. See doc/driver-model/migration.rst for more info. ==================================================== Signed-off-by: NPatrice Chotard <patrice.chotard@st.com> Acked-by: NPatrick Delaunay <patrick.delaunay@st.com>
-
- 21 10月, 2019 13 次提交
-
-
由 Patrick Delaunay 提交于
Correct the name of the define used CONFIG_IS_ENABLED which is not aligned with Kconfig name: CONFIG_$(SPL_)PINCONF_RECURSIVE. The recursive calls is conditional only for UCLASS_PINCONFIG "pinconfig" driver. It is always needed to call pinctrl_post_bind for UCLASS_PINCTRL "pinctrl", the test CONFIG_IS_ENABLED(PINCONF_RECURSIVE) need to be removed for this driver. This correct a regression introduced because the same patch is applied twice times in u-boot-dm branch: - commit e878b53a ("dm: pinctrl: introduce PINCONF_RECURSIVE option") - commit c20851b3 ("dm: pinctrl: introduce PINCONF_RECURSIVE option") Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
-
由 Patrick Delaunay 提交于
Remove the duplicated configs introduced when the same patch is applied twice times: - commit e878b53a ("dm: pinctrl: introduce PINCONF_RECURSIVE option") - commit c20851b3 ("dm: pinctrl: introduce PINCONF_RECURSIVE option") Signed-off-by: NPatrick Delaunay <patrick.delaunay@st.com>
-
由 Biwen Li 提交于
To allow OCRAM to be used as wakeup source in deep sleep, do not power it down. Signed-off-by: NBiwen Li <biwen.li@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Biwen Li 提交于
The patch adds an errata ID A-008646 for workaround to provide more information by errata ID. Signed-off-by: NBiwen Li <biwen.li@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Wasim Khan 提交于
LX2160A/LX2120A/LX2080A SVR value should be 0x873600/0x873620/0x873602 Previous values were valid only if CAN fuse is blown. Signed-off-by: NWasim Khan <wasim.khan@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Yuantian Tang 提交于
ls1028a has 4 personalities: ls1028a, ls1027a, ls1017a and ls1018a. Both ls1027a and ls1017a personalities are lower functionality version which doesn't support the multimedia subsystems, like LCD, GPU. To disable multimedia feature on non-multimedia version, set the status property to disabled in dts nodes. Signed-off-by: NTang Yuantian <andy.tang@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Udit Agarwal 提交于
Adds sec_init call to initialise the job ring parameters for secure boot operations. Signed-off-by: NUdit Agarwal <udit.agarwal@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Kuldeep Singh 提交于
This configuration enables picking the environment from flash before DDR init. Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Biwen Li 提交于
The patch corrects endianness of register SCFG_SPARECR8 read in_le32 -> in_be32 Signed-off-by: NBiwen Li <biwen.li@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Ran Wang 提交于
Program register bit of SCFG_SNPCNFGCR_USBxRDSNP and SCFG_SNPCNFGCR_USBxWRSNP(x = 1, 2, 3) to drive USBx read/write snoop signal on LS1043A and LS1046A. Signed-off-by: NRan Wang <ran.wang_1@nxp.com> Reviewed-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Kuldeep Singh 提交于
Update SCFG_QSPI_CLKSEL value : 0xC -> 0x5 which means ClusterPLL/16 Signed-off-by: NAshish Kumar <Ashish.kumar@nxp.com> Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Kuldeep Singh 提交于
CONFIG_ENV_ADDR config option enables picking the environment from flash before DDR init. Signed-off-by: NAshish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: NKuldeep Singh <kuldeep.singh@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
由 Yuantian Tang 提交于
Add LS1027A, LS1018A and LS1017A personalities support to LS1028A SoC family. LS1028A is the prime personality of LS1028A SoC family. LS1027A is a lower funtionality version of QorIQ LS1028A which does not support the multimedia subsystems, such as LCD controller, GPU, and eDP PHY. The QorIQ LS1018A and LS1017A SoCs are single 64-bit Arm A72 core, low power versions of the QorIQ LS1028A and LS1027A SoCs respectively. Signed-off-by: NTang Yuantian <andy.tang@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com>
-
- 19 10月, 2019 4 次提交
-
-
由 Anatolij Gustschin 提交于
Loading U-Boot on i.MX8QXP MEK board is broken since recent changes in spl_mmc: U-Boot SPL 2019.10-00162-gff5bd397e4 (Oct 18 2019 - 15:50:45 +0200) Normal Boot WDT: Not found! Trying to boot from MMC2_2 Load image from MMC/SD 0x46400 spl: mmc partition switch failed SPL: failed to boot from all boot devices ### ERROR ### Please RESET the board ### The newly added CONFIG_SYS_MMCSD_RAW_MODE_EMMC_BOOT_PARTITION option is selected automatically and overrides the EXT_CSC_PART_CONFIG configurations with default value, always selecting the eMMC boot partition 1. Boards which place U-Boot image in other partitions became not bootable. Fix this by making the eMMC HW boot partition selection optional. Fixes: 17241ea0 (spl: mmc: Add option to set eMMC HW boot partition) Reviewed-by: NLukasz Majewski <lukma@denx.de> Signed-off-by: NAnatolij Gustschin <agust@denx.de>
-
https://gitlab.denx.de/u-boot/custodians/u-boot-efi由 Tom Rini 提交于
Pull request for UEFI sub-system for efi-2020-01-rc1 (2) Install the simple file protocol only if there is a file system on the partition. Enable CONFIG_CMD_NVEDIT_EFI on QEMU.
-
https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic由 Tom Rini 提交于
- document alternative libretech-cc installation methods, including upstream TF-A and opensource tools - add HDMI/CVBS display support for Amlogic G12A SoCs and SEI510 board - add support for Amlogic A311D based Khadas VIM3 - add support for Amlogic S905X3 based SEI610 board, targeting Android support like SEI510
-
https://gitlab.denx.de/u-boot/custodians/u-boot-riscv由 Tom Rini 提交于
- Support sifive DM based gpio driver for FU540-SoC. - Align boot image header with Linux v5.3
-
- 18 10月, 2019 11 次提交
-
-
由 Guillaume La Roque 提交于
Add separate config file to handle the different eMMC size on the sei610 board. Signed-off-by: NGuillaume La Roque <glaroque@baylibre.com> Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Guillaume La Roque 提交于
Move android generic config and boot sequence in meson64_android header and fix size of userdata to use all eMMC on SEI510. Signed-off-by: NGuillaume La Roque <glaroque@baylibre.com> Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Neil Armstrong 提交于
Add support for the customer board SEI610 manufactured by SEI Robotics with the following specifications: - Amlogic S905X3 ARM Cortex-A55 quad-core SoC - 2GB DDR4 SDRAM - 10/100 Ethernet (Internal PHY) - 1 x USB 3.0 Host - 1 x USB Type-C DRD - 1 x FTDI USB Serial Debug Interface - eMMC - SDcard - Infrared receiver - SDIO WiFi Module Like it's SEI510 counterpart, the boot flow is designed to boot Android AOSP built for the Yukawa Android device. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Neil Armstrong 提交于
Rename meson-g12a-u-boot.dtsi into meson-g12-common-u-boot.dtsi to match the new DT architecture and add meson-sm1-sei610-u-boot.dtsi to handle the U-Boot specific DT for graphics. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Neil Armstrong 提交于
The GX VPU Power Domain driver has been replaced by the Everything-Else Power Domain driver for G12A and SM1. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Neil Armstrong 提交于
Based on the 54ecb8f7028c ("Linux 5.4-rc1") Everything-Else power domain driver for Amlogic SoCs. This driver handles the VPU Power domain and other domains from the Everything-Else part of the SM1 and G12A SoCs. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Neil Armstrong 提交于
Import the Amlogic SM1 DT and the SEI610 board DT from [1] [1] da0c9ea146cb ("Linux 5.4-rc2") Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Neil Armstrong 提交于
The SM1 clock controller is almost identical to the G12A and so far the differences don't matter. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Neil Armstrong 提交于
Add support for mmc-pwrseq-emmc in the meson-gx mmc driver to support enabling the eMMC. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Neil Armstrong 提交于
Add the missing IDs to detect the SM1 S905X3 SoC. Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-
由 Andreas Färber 提交于
Values imported from Linux driver, but in correct numeric order. Khadas VIM3 prints: Amlogic Meson G12B (A311D) Revision 29:b (10:2) Cc: Christian Hewitt <christianshewitt@gmail.com> Signed-off-by: NAndreas Färber <afaerber@suse.de> Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
-