- 11 9月, 2017 8 次提交
-
-
由 Udit Agarwal 提交于
Adds header address for PPA to be validated during ESBC phase for ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It must be initialized before the PPA. Signed-off-by: NUdit Agarwal <udit.agarwal@nxp.com> [YS: revised commit message] Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Sumit Garg 提交于
Unify memory map for Layerscape based platforms. This patch includes changes in bootscript, bootscript header and PPA header addresses change as per unified memory map. Signed-off-by: NSumit Garg <sumit.garg@nxp.com> Tested-by: NVinitha Pillai <vinitha.pillai@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Zhao Qiang 提交于
QE_IRAM_READY should be set only after successfully uploading the firmware. Signed-off-by: NZhao Qiang <qiang.zhao@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Ashish Kumar 提交于
CoreLink Cache Coherent Interconnect (CCI) provides full cache coherency between two clusters of multi-core CPUs and I/O coherency for devices and I/O masters. This patch add new config option SYS_FSL_HAS_CCI400 and moves existing register space definaton of CCI-400 bus to fsl_immap to be shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET in Kconfig. Signed-off-by: NAshish Kumar <Ashish.Kumar@nxp.com> Signed-off-by: NPrabhakar Kushwaha <prabhakar.kushwaha@nxp.com> [YS: revised commit message, squashed patches for armv8 and armv7] Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Bin Meng 提交于
At present the IDE device number is initialized to -1, which means we cannot type "ide read" command before setting the device number via "ide device #". For convenience, let's set the first device as the default one. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
When there is no CDROM inserted, the block size is zero hence there is no need to create a BLK device for it. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
This converts the IDE driver to driver model so that block read and write are fully functional. Fixes: b7c6baef ("x86: Convert MMC to driver model") Reported-by: NHeinrich Schuchardt <xypron.glpk@gmx.de> Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Tested-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Bin Meng 提交于
So far these are using magic numbers. Replace them with macros. Signed-off-by: NBin Meng <bmeng.cn@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
- 09 9月, 2017 2 次提交
-
-
由 Tom Rini 提交于
This board does dwc3 gadget, not host, so we cannot have host support or we will fail to link. Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Tom Rini 提交于
The underlying implementation for ENV_AES has security complications and is not recommended for use. Please see CVE-2017-3225 and CVE-2017-3226 for more details. Mark this as deprecated now and delete this in the medium term if no one comes forward to re-work the support. Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 08 9月, 2017 16 次提交
-
-
由 Chris Packham 提交于
A number of the config options for USB networking have been migrated to Kconfig. Update README.usb to reflect this. Signed-off-by: NChris Packham <judge.packham@gmail.com>
-
由 Chris Packham 提交于
This migrates ASIX, ASIX88179, MCS7830, RTL8152 and SMSC95XX to Kconfig. Update defconfigs. Signed-off-by: NChris Packham <judge.packham@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Chris Packham 提交于
CONFIG_USB_HOST_ETHER is the framework that the drivers are dependent on USB_HOST_ETHER. Use this as a menu and move the existing LAN75XX and LAN78XX options under new menu. Finally update the defconfigs that need CONFIG_USB_HOST_ETHER. Signed-off-by: NChris Packham <judge.packham@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Chris Packham 提交于
This is not a valid option. Drop it. Signed-off-by: NChris Packham <judge.packham@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Chris Packham 提交于
This is not a valid option. Drop it. Signed-off-by: NChris Packham <judge.packham@gmail.com> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Nobuhiro Iwamatsu 提交于
The correct name is 'gd->fdt_blob', not 'gd->blob'. Signed-off-by: NNobuhiro Iwamatsu <iwamatsu@nigauri.org> CC: Simon Glass <sjg@chromium.org> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Tom Rini 提交于
Rsync all defconfig files using moveconfig.py Signed-off-by: NTom Rini <trini@konsulko.com>
-
由 Kever Yang 提交于
With Makefiles testing for $(SPL_TPL_)SYSRESET, we need SPL_SYSRESET for do_reset() in SPL for Rockchip SoCs. References: 87c16d49 "drivers: spl: consistently use the $(SPL_TPL_) macro" Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Kever Yang 提交于
syscon id table need a dummy member as NULL ending, or else system will panic while try to match a compatible in this table as a list. Signed-off-by: NKever Yang <kever.yang@rock-chips.com> Acked-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com> Reviewed-by: NPhilipp Tomsich <philipp.tomsich@theobroma-systems.com>
-
由 Marek Vasut 提交于
Disable CONFIG_ARCH_FIXUP_FDT_MEMORY to prevent U-Boot from modifying the memory {} nodes in the DT passed to the Linux kernel. The R8A779x DT contains multiple memory {} nodes, while U-Boot only modifies the first one and stuffs all the memory entries into it, which is wrong. Disabling CONFIG_ARCH_FIXUP_FDT_MEMORY is the least intrusive way to fix the issue this close to the release, while the real fix is to extend the fdt_fixup_memory_banks() to handle multiple memory nodes in DT. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
由 Marek Vasut 提交于
On RCar M3 and on RCar H3 newer than and not including ES1.0, the SD clock must be divided by 4 rather than 2 because a hardware workaround present only in the H3 ES1.0 has been removed from these chips. U-Boot currently only supports M3 and H3 ES 2.0 and newer, so configure the SD pre-divider to 4 to prevent SD instability. Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-
-
由 Heinrich Schuchardt 提交于
%s/Desriptor/Descriptor/g Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Madalin Bucur 提交于
Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> Acked-by: NYork Sun <york.sun@nxp.com>
-
由 Tom Rini 提交于
In the general case, CONFIG_NFS_READ_SIZE is unchanged from the default of 1024. There are in fact no in-tree users that increase this size. Adjust the comment to reflect what could be done in the future in conjunction with CONFIG_IP_DEFRAG. Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: NTom Rini <trini@konsulko.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
-
由 Madalin Bucur 提交于
The old logic always enabled the TX-delay when the phy-mode was set to PHY_INTERFACE_MODE_RGMII. With this patch we enable the TX delay for PHY_INTERFACE_MODE_RGMII_ID and PHY_INTERFACE_MODE_RGMII_TXID and disable it for PHY_INTERFACE_MODE_RGMII. Based on a similar change made in the Linux Realtek PHY driver by Martin Blumenstingl <martin.blumenstingl@googlemail.com>. Signed-off-by: NMadalin Bucur <madalin.bucur@nxp.com> Acked-by: NJoe Hershberger <joe.hershberger@ni.com> Acked-by: NYork Sun <york.sun@nxp.com>
-
- 07 9月, 2017 8 次提交
-
-
由 Kever Yang 提交于
Delete one redundant 'which' for SPL_ATF_SUPPORT description. Signed-off-by: NKever Yang <kever.yang@rock-chips.com>
-
由 Heinrich Schuchardt 提交于
Remove a comment line refering to a non-existent file. Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Heinrich Schuchardt 提交于
The inline documentation of vsprintf mentions a parameter size which does not exist in the function declaration. int vsprintf(char *buf, const char *fmt, va_list args); Signed-off-by: NHeinrich Schuchardt <xypron.glpk@gmx.de>
-
由 Paul Barker 提交于
This reverts commit 25877d4e. This is a workaround for Raspberry Pi boot failures seen when passing on the device tree provided by the Raspberry Pi firmware at boot. Without CONFIG_OF_EMBED, we just get stuck at "Starting kernel ..." when we try to boot Linux with this device tree. Signed-off-by: NPaul Barker <pbarker@toganlabs.com> Cc: Simon Glass <sjg@chromium.org> Tested-by: NJonathan Gray <jsg@jsg.id.au> Reviewed-by: NSimon Glass <sjg@chromium.org>
-
由 Bin Meng 提交于
Some files are generated during libfdt build. Ignore them. This was wrongly put in the .gitignore in the root directory before. Now let's remove entries there and put them in the right place. Fixes: 34e2c285 ("gitignore: add intermediates from libfdt build") Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Bin Meng 提交于
These are currently out of alphabetical order. Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
-
由 Alison Chaiken 提交于
Signed-off-by: NAlison Chaiken <alison@she-devel.com>
-
由 Bin Meng 提交于
Change to use 'debug' to output the error message if it fails to read the driver descriptor block. Signed-off-by: NBin Meng <bmeng.cn@gmail.com>
-
- 06 9月, 2017 4 次提交
-
-
由 Simon Glass 提交于
The target is not currently mentioned anywhere. Add it to the help so people can find it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This was broken by the recent environment refactoring. Specifically: $ make environ scripts/Makefile.build:59: tools/environ/Makefile: No such file or directory make[1]: *** No rule to make target 'tools/environ/Makefile'. Stop. make: *** [Makefile:1469: environ] Error 2 Fix this by updating the Makefile and adjusting the #include filesnames in two C files. Fixes: ec74f5f9 (Makefile: Rename 'env' target to 'environ') Reported-by: NMåns Rullgård <mans@mansr.com> Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Sam Protsenko 提交于
Since commit 842778a0 ("usb: gadget: g_dnl: only set iSerialNumber if we have a serial#") "fastboot devices" stopped to show correct device serial number for TI boards, showing this line instead: ???????????? fastboot This is because serial# env variable could be set after g_dnl gadget was initialized (e.g. by using env_set() in the board file). To fix this, let's update internal serial number variable (g_dnl_serial) when "serial#" env var is changed. Signed-off-by: NSam Protsenko <semen.protsenko@linaro.org> Cc: Felipe Balbi <felipe.balbi@linux.intel.com> Tested-by: NHeiko Schocher <hs@denx.de> Acked-by: NŁukasz Majewski <lukma@denx.de> Reviewed-by: NMarek Vasut <marex@denx.de>
-
由 Tom Rini 提交于
With the move of environment code from common/ to env/ a number of changes needed to be made to various make targets. We missed updating some of the files required for out of tree builds of the tools. Correct the 'environ' target to know that we need to work under tools/env/ still (not tools/environ/) and then update the wrappers in env_attr.c and env_flags.c to point to the new correct file. Reported-by: NPeter Robinson <pbrobinson@gmail.com> Tested-by: NPeter Robinson <pbrobinson@gmail.com> Signed-off-by: NTom Rini <trini@konsulko.com>
-
- 05 9月, 2017 2 次提交
-
-