Skip to content

U
U-Boot.Mirror

OS / U-Boot.Mirror

通知 1
Star 0
Fork 0
U
U-Boot.Mirror

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 01 9月, 2021 2 次提交
  3. 27 7月, 2021 1 次提交
  5. 28 6月, 2021 1 次提交
  7. 09 6月, 2021 1 次提交
  9. 12 5月, 2021 1 次提交
  11. 01 12月, 2020 1 次提交
  13. 10 10月, 2020 1 次提交
  15. 22 9月, 2020 1 次提交
  17. 17 9月, 2020 1 次提交
    • I
      colibri_vf: use preboot for fdtfile evaluation · 3ab2316a
      由 Igor Opaniuk 提交于 
      Enable and set preboot var with fdtfile evaluation.
preboot will be checked and run immediately before starting the
CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp.
entering interactive mode.

This provides possibility to use different boot cmds in interactive mode
without manual setting fdtfile value, as it it's already evaluated
before entering interactive mode.

Fixes: 304042c1("colibri_vf: set fdtfile for distroboot")
Signed-off-by: NIgor Opaniuk <igor.opaniuk@toradex.com>
      3ab2316a
  19. 24 8月, 2020 1 次提交
  21. 11 8月, 2020 1 次提交
  23. 29 7月, 2020 1 次提交
  25. 28 7月, 2020 1 次提交
  27. 22 6月, 2020 1 次提交
  29. 09 5月, 2020 1 次提交
  31. 07 2月, 2020 1 次提交
  33. 23 1月, 2020 1 次提交
  35. 06 12月, 2019 1 次提交
  37. 05 12月, 2019 4 次提交
  39. 04 12月, 2019 2 次提交
  41. 21 11月, 2019 2 次提交
    • T
      env: Finish migration of common ENV options · a09fea1d
      由 Tom Rini 提交于 
      - In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
      a09fea1d
    • T
      env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol · 8d8ee47e
      由 Tom Rini 提交于 
      Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NTom Rini <trini@konsulko.com>
      8d8ee47e
  43. 23 9月, 2019 1 次提交
  45. 14 8月, 2019 1 次提交
  47. 29 7月, 2019 1 次提交
  49. 23 6月, 2019 1 次提交
  51. 11 6月, 2019 1 次提交
  53. 15 5月, 2019 1 次提交
    • J
      net: phy: micrel: Allow KSZ8xxx and KSZ90x1 to be used together · 77b508d3
      由 James Byrne 提交于 
      Commit d397f7c4 ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.

This commit contains the following changes:

- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.
Signed-off-by: NJames Byrne <james.byrne@origamienergy.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
      77b508d3
  55. 30 4月, 2019 1 次提交
  57. 14 4月, 2019 5 次提交
  59. 09 1月, 2019 1 次提交