- Provide a default Kconfig value of the default script
- Largely continue to define this via the board Kconfig file
- For the boards that select a script based on defconfig rather than
  TARGET, keep this within the defconfig.
Signed-off-by: NTom Rini <trini@konsulko.com>

Now that we have consistent usage, migrate this symbol to Kconfig.
Signed-off-by: NTom Rini <trini@konsulko.com>
Reviewed-by: NRick Chen <rick@andestech.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

TFTP transfer size can be used to re-size the TFTP progress bar on
single line based on the server reported file size. The support for
this has been around from 2019, but it was never converted to proper
Kconfig.

While adding this new Kconfig, enable it by default for OMAP2+ and K3
devices also.
Signed-off-by: NTero Kristo <kristo@kernel.org>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

The Toradex product is called colibri-imx8x consisting of SoM with
i.MX8QXP and i.MX8DX SoCs.
Signed-off-by: NPhilippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: NIgor Opaniuk <igor.opaniuk@toradex.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_SYS_MMC_ENV_DEV
   CONFIG_SYS_MMC_ENV_PART

Note that with this conversion we now have consistent behavior with
respect to ensuring that we have always selected the correct MMC
device and hardware partition.
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_ENV_OVERWRITE
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Rerun migration, remove some comments]
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

This got dropped by a global 'make savedefconfig' resync as
required patches are still in flight.
Signed-off-by: NMax Krummenacher <max.krummenacher@toradex.com>

Move below defines which are used by mtest utility to Kconfig.
CONFIG_SYS_MEMTEST_START
CONFIG_SYS_MEMTEST_END
Signed-off-by: NAshok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
[trini: Fix kmcoge5ne board, re-run migration as well]
Signed-off-by: NTom Rini <trini@konsulko.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: NTom Rini <trini@konsulko.com>
Acked-by: NJoe Hershberger <joe.hershberger@ni.com>
Reviewed-by: NSimon Goldschmidt <simon.k.r.goldschmidt@gmail.com>

Today in initr_reloc_global_data() we use some non-obvious tests to
determine if we need to relocate the env_addr within gd or not.  In
order to facilitate migration of other symbols to Kconfig we need to
introduce a new symbol for this particular use case.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: NTom Rini <trini@konsulko.com>

Migrate all of the existing OS support options that are under
CONFIG_BOOTM_* to Kconfig.
Signed-off-by: NTom Rini <trini@konsulko.com>

This converts the following to Kconfig:
   CONFIG_FSL_USDHC
Signed-off-by: NAdam Ford <aford173@gmail.com>
[trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list]
Signed-off-by: NTom Rini <trini@konsulko.com>

Converted to use fsl_esdhc_imx for i.MX platforms.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Tested-by: NSteffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>
Reviewed-by: NMartyn Welch <martyn.welch@collabora.com>
Acked-by: NJason Liu <Jason.hui.liu@nxp.com>

Moved CONFIG_FSL_ESDHC from header files to defconfig files.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Tested-by: NSteffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: NPeng Fan <peng.fan@nxp.com>
Reviewed-by: NLukasz Majewski <lukma@denx.de>
Reviewed-by: NMartyn Welch <martyn.welch@collabora.com>
Acked-by: NJason Liu <Jason.hui.liu@nxp.com>

Rsync all defconfig files using moveconfig.py
Signed-off-by: NTom Rini <trini@konsulko.com>

Convert CONFIG_TFTP_BLOCKSIZE to Kconfig, update defconfigs,
headers and whitelist.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>

Convert CONFIG_IP_DEFRAG to Kconfig, update defconfigs, headers
and whitelist. This patch is a follow-up on a patch by Christian
Gmeiner with the added config/header/whitelist updates.
Signed-off-by: NMarek Vasut <marek.vasut+renesas@gmail.com>
Reported-by: NChristian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>

This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB
IT V1.0B module. Unlike the V1.0A early access samples exclusively
booting from SD card, they are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.

Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet
- GPIOs
- I2C

Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
Signed-off-by: NMarcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: NIgor Opaniuk <igor.opaniuk@toradex.com>