- 02 6月, 2017 2 次提交
-
-
由 Bogdan Purcareata 提交于
Previous to MC v10.x, port mac address was specified via DPL. Since newer MC versions are compatible with old style DPLs, make the u-boot env mac addresses visible there. This applies only to DPLs that have an older version. DPLs use 32 bit values for specifying MAC addresses. U-boot environment variables take precedence over the MAC addresses already visible in the DPL/DPC. Signed-off-by: NBogdan Purcareata <bogdan.purcareata@nxp.com> Signed-off-by: NHeinz Wrobel <heinz.wrobel@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Bogdan Purcareata 提交于
DPAA2 platforms boot the Management Complex based on the u-boot env variable "mcinitcmd". Instead of doing this step on each platform individually, define a single mc_env_boot function in the MC driver, since it's semantically tied to it. Call the function in a per-board reset_phy hook, as it gets called at a later moment, when all board PHY devices have been initialized. Signed-off-by: NBogdan Purcareata <bogdan.purcareata@nxp.com> Signed-off-by: NHeinz Wrobel <heinz.wrobel@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 26 5月, 2017 2 次提交
-
-
-
git://git.denx.de/u-boot-nds32由 Tom Rini 提交于
Move FTMAC100 to where it should be, alphabetically in drivers/net/Kconfig Signed-off-by: NTom Rini <trini@konsulko.com> Conflicts: drivers/net/Kconfig
-
- 24 5月, 2017 17 次提交
-
-
-
由 Udit Agarwal 提交于
This patch adjusts memory map for secure boot headers on LS2080AQDS and LS2080ARDB platforms. Secure boot headers are placed on NOR flash at offset 0x00600000. Signed-off-by: NUdit Agarwal <udit.agarwal@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Santan Kumar 提交于
This patch adjusts memory map for images on LS2080ARDB and LS2080AQDS NOR flash as below Image Flash Offset RCW+PBI 0x00000000 Boot firmware (U-Boot) 0x00100000 Boot firmware Environment 0x00300000 PPA firmware 0x00400000 PHY firmware 0x00980000 DPAA2 MC 0x00A00000 DPAA2 DPL 0x00D00000 DPAA2 DPC 0x00E00000 Kernel.itb 0x01000000 Signed-off-by: NSantan Kumar <santan.kumar@nxp.com> Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Alison Wang 提交于
This patch is to adjust the memory mapping for FLash/SD card on LS1046AQDS and LS1046ARDB, such as FMAN firmware load address, U-Boot start address on serial flash and environment address. Signed-off-by: NAlison Wang <alison.wang@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Alison Wang 提交于
This patch is to adjust the memory mapping for FLash/SD card on LS1043AQDS and LS1043ARDB, such as PPA firmware load address, FMAN firmware load address, QE firmware load address, U-Boot start address on serial flash and environment address. Signed-off-by: NAlison Wang <alison.wang@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Alison Wang 提交于
This patch is to adjust the memory mapping for FLash/SD card on LS1021AQDS and LS1021ATWR, such as U-Boot start address on serial Flash, QE firmware load address and environment address. Signed-off-by: NAlison Wang <alison.wang@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Priyanka Jain 提交于
LS2081ARDB board is similar to LS2080ARDB board with few differences It hosts LS2081A SoC Default boot source is QSPI-boot It does not have IFC interface RTC and QSPI flash device are different It provides QIXIS access via I2C Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com> Signed-off-by: NSantan Kumar <santan.kumar@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Priyanka Jain 提交于
The QorIQ LS2081A SoC has eight 64-bit ARM v8 Cortex A72 cores and is built on layerscape architecture. It is 40-pin derivative of LS2084A (non-AIOP personality of LS2088A). So feature-wise it is same as LS2084A. LS2041A is a 4-core personality of LS2081A. Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com> Signed-off-by: NSantan Kumar <santan.kumar@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Priyanka Jain 提交于
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC. LS2088ARDB RevF Board has limitation that QIXIS can not be accessed. CONFIG_FSL_QIXIS is not enabled. Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com> Signed-off-by: NSuresh Gupta <suresh.gupta@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Priyanka Jain 提交于
Update QIXIS related code to be executed only if CONFIG_FSL_QIXIS flag is enabled. In case QIXIS code is not enabled, use default sysclk value as 100MHz per board documentation. Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Yogesh Gaur 提交于
Earlier when MC is loaded but DPL is not deployed results in FDT fix-up code execution hangs. For this case now print message on console and return success instead of return -ENODEV. This update allows fdt fixup to continue execution. Signed-off-by: NYogesh Gaur <yogeshnarayan.gaur@nxp.com> Signed-off-by: NPriyanka Jain <Priyanka.jain@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 York Sun 提交于
This allows using PCIe NIC without enabling DPAA FMan. Signed-off-by: NYork Sun <york.sun@nxp.com> CC: Mingkai Hu <mingkai.hu@nxp.com> Acked-by: NMingkai Hu <mingkai.hu@nxp.com>
-
由 York Sun 提交于
This allows using PCIe NIC without enabling DPAA FMan. Signed-off-by: NYork Sun <york.sun@nxp.com> CC: Mingkai Hu <mingkai.hu@nxp.com> Acked-by: NMingkai Hu <mingkai.hu@nxp.com>
-
由 Suresh Gupta 提交于
LS1012AFRDM, LS1012ARDB, LS1012AQDS all have S25FS512S flash of 64MB size. Signed-off-by: NSuresh Gupta <suresh.gupta@nxp.com>
-
由 Suresh Gupta 提交于
ls1012ardb, ls1046ardb, ls2080ardb have S25FS512S flash which does not support Bank Address Register commands. Signed-off-by: NSuresh Gupta <suresh.gupta@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Priyanka Jain 提交于
LS2080ARDB/LS2088ARDB RevF board has smart voltage translator which needs to be programmed to enable high speed SD interface by setting GPIO4_10 output to zero. Signed-off-by: NPriyanka Jain <priyanka.jain@nxp.com> Signed-off-by: NSantan Kumar <santan.kumar@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
由 Hou Zhiqiang 提交于
Signed-off-by: NHou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: NYork Sun <york.sun@nxp.com>
-
- 23 5月, 2017 19 次提交
-
-
由 rick 提交于
Support Andestech eth ftmac100 device tree flow on AG101P/AE3XX platform. Verification: Boot linux kernel via dhcp and bootm ok. NDS32 # setenv bootm_size 0x2000000;setenv fdt_high 0x1f00000; NDS32 # dhcp 0x600000 10.0.4.97:boomimage-310y-ae300-spi.bin BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 DHCP client bound to address 10.0.4.178 (4899 ms) Using mac@e0100000 device TFTP from server 10.0.4.97; our IP address is 10.0.4.178 Filename 'boomimage-310y-ae300-spi.bin'. Load address: 0x600000 Loading: ################################################################# ################################################################# ################################################################# ... ... ################################### 233.4 KiB/s done Bytes transferred = 13872076 (d3abcc hex) NDS32 # dhcp 0x2000000 10.0.4.97:ae300.dtb BOOTP broadcast 1 BOOTP broadcast 2 BOOTP broadcast 3 BOOTP broadcast 4 DHCP client bound to address 10.0.4.178 (4592 ms) Using mac@e0100000 device TFTP from server 10.0.4.97; our IP address is 10.0.4.178 Filename 'ae300.dtb'. Load address: 0x2000000 Loading: # 82 KiB/s done Bytes transferred = 2378 (94a hex) NDS32 # bootm 0x600000 - 0x2000000 Image Name: Created: 2017-03-22 6:52:03 UTC Image Type: NDS32 Linux Kernel Image (uncompressed) Data Size: 13872012 Bytes = 13.2 MiB Load Address: 0000c000 Entry Point: 0000c000 Verifying Checksum ... OK Booting using the fdt blob at 0x2000000 Loading Kernel Image ... OK Loading Device Tree to 01efc000, end 01eff949 ... OK Linux version 3.10.102-20375-gb0034c1-dirty (rick@app09) (gcc version 4.9.3 (2016-07-06_nds32le-linux-glibc-v3_experimental) ) #293 PREEMPT Wed Mar 22 14:49:28 CST 2017 CPU: NDS32 N13, AndesCore ID(wb), CPU_VER 0x0d11103f(id 13, rev 17, cfg 4159) ... ... Signed-off-by: Nrick <rick@andestech.com>
-
由 Tom Rini 提交于
In situations like an autobuilder we are likely to not have bl31.bin present and thus would fail to build and propagate the error upwards. Instead, print a big warning to stderr so that human will see that something is wrong but complete the build. Cc: Maxime Ripard <maxime.ripard@free-electrons.com> Reviewed-by: NAndre Przywara <andre.przywara@arm.com> Reviewed-by: NSimon Glass <sjg@chromium.org> Signed-off-by: NTom Rini <trini@konsulko.com>
-
git://git.denx.de/u-boot-sunxi由 Tom Rini 提交于
trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't get Kconfig errors on platforms without SPL, ie sandbox (without SPL). Signed-off-by: NTom Rini <trini@konsulko.com>
-
-
-
由 Lothar Waßmann 提交于
The original commit for the MCF54418TWR ColdFire development board support defined a 'CONFIG_SYS_FAULT_ECCONFIG_SYS_NO_FLASHHO_LINK_DOWN' which obviously has a rogue 'CONFIG_SYS_NO_FLASH' embedded in the intended 'CONFIG_SYS_FAULT_ECHO_LINK_DOWN' define. Signed-off-by: NLothar Waßmann <LW@KARO-electronics.de>
-
由 Simon Glass 提交于
Enable this option by default on sandbox to increase build coverage. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_LZMADEC Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_LZMA Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This is not used in U-Boot. Drop it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_KGDB Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_IRQ Signed-off-by: NSimon Glass <sjg@chromium.org> Reviewed-by: NTom Rini <trini@konsulko.com>
-
由 Simon Glass 提交于
Rather than using CMD_JFFS2 for both the filesystem and its command, we should have a separate option for each. This allows us to enable JFFS2 support without the command, if desired, which reduces U-Boot's size slightly. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_JFFS2 Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_IOTRACE Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_IOLOOP Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This converts the following to Kconfig: CONFIG_CMD_IO Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This option is not used in U-Boot. Drop it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-
由 Simon Glass 提交于
This option is not used in U-Boot. Drop it. Signed-off-by: NSimon Glass <sjg@chromium.org>
-